• Korean Journal of Applied Biomechanics
• /
• v.25 no.1
• /
• pp.29-37
• /
• 2015

Objective : The purpose of this study was to investigate the biomechanical properties of shock absorption strategy and postural stability during the drop landing for each types. Methods : The motions were captured with Vicon Motion Capture System, with the fourteen infra-red cameras (100Hz) and synchronized with GRF(ground reaction force) data(1000Hz). Ten male soccer players performed a drop landing with single-leg and bi-legs on the 30cm height box. Dependent variables were the CoM trajectory and the Joint Moment. Statistical computations were performed using the paired t-test and ANOVA with Turkey HSD as post-hoc. Results : The dominant leg was confirmed to show a significant difference between the left leg and right leg as the inverted pendulum model during Drop Landing(Phase 1 & Phase 2). One-leg drop landing type had the higher CoM displacement, the peak of joint moment with the shock absorption than Bi-leg landing type. As a lower extremity joint kinetics analysis, the knee joint showed a function of shock absorption in the anterior-posterior, and the hip joint showed a function of the stability and shock absorption in the medial-lateral directions. Conclusion : These findings indicate that the instant equilibrium of posture balance(phase 1) was assessed by the passive phase as Class 1 leverage on the effect of the stability of shock absorption(phase 2) assessed by the active phase on the effect of Class 2 leverage. Application : This study shows that the cause of musculo-skeletal injuries estimated to be focused on the passive phase of landing and this findings could help the prevention of lower damage from loads involving landing related to the game of sports.

• Journal of the Korean Arthroscopy Society
• /
• v.2 no.1
• /
• pp.85-92
• /
• 1998

Various methods for fixation of graft have been widely used for reconstruction of anterior cruciate ligament. However, the biomechanical strength of each fixation techniques are not fully understood. The purpose of this study is to compare the pull out strength of different fixation techniques which is probably the most important factor for the success at the initial stage of healing. Biomechanical test was carried out to measure and compare the pull out tensile strength of five different fixation techniques in 35 pig(Yorkshire) knees. ANOVA and Duncan multiple comparison test was applied for statistical analysis. In the two fixation techniques with bone patellar tendon bone graft, the mean maximum tensile strength was $1333.4{\pm}148.5N$ with titanium interference screw, while it was $1310.1{\pm}168.9N$ with biodegradable interference screw. The failure mode were pulled out of bone plugs from the femoral tunnel in majority cases. In the fixations with hamstring tendon, the mean maximum tensile strength were $1405.9{\pm}135.1N$ with SemiFix screw, $820.3{\pm}104.5N$ with biodegradable interference screw, and $682.1{\pm}54.2N$ with Endobutton. The mode of failure was variable in each technique. The tendon was pulled out from the tunnel in biodegradable interference screw fixation, the screw was bent in the SemiFix system, and the polyester tape were ruptured or the buttons were pulled into tunnel in Endobutton fixation. The mean maximum tensile strength of two interference screws with bone patellar tendon bone was statistically comparable to that of SemiFix with hamstring tendon. However biodegradable interference screw and Endobutton with hamstring tendon showed weaker maximum tensile strength than above three fixation techniques (P<0.05).

• Korean Journal of Applied Biomechanics
• /
• v.16 no.3
• /
• pp.53-63
• /
• 2006

The general objective of this study was to investigate biomechanical characteristics of bowling swing using three-dimensional cinematography. This study focused specifically on movements of the upper body segments during a bowling swing. Eight elite female bowling players participated in this study. Subjects performed bowling swing and their performance was sampled at 60 frame/sec using two high-speed video cameras with a synchronizer. After digitizing images from two cameras, the two-dimensional coordinates were used to produce three-dimensional coordinates of the 12 body segments (20 joint reference makers). The obtained three-dimensional coordinates were fed to a custom-written kinematic and kinetic analyses program (LabView 6.1, National Instrument, Austin, TX, USA). The analyses determined the linear and angular kinematic variables of the body segments with which joint force and torque of the lower and upper trunks and the shoulder were estimated based on the Newton-Euler equations. It was found that during the bowling swing the peak linear velocities of the body segments were reached in sequence the trunk, the shoulder, the elbow, the wrist, and the bowl. This result indicates that linear momentum of the lower body and the trunk transmits to the arm segment during the bowling swing. The joint torques of the torso and the arm occurred almost simultaneously, indicating that bowling swing seem to be a push-like motion, rather than a proximal-distal sequence motion in which many of throwing motions are categorized. The ultimate objective of the bowling swing is to release a heavy-weight bowl with power and consistency. Therefore, the bowling swing observed in this study well agrees with that bowlers use the stepping to increase the linear velocity of the bowl, the simple pendulum system and the push-like segmental motion in the torso and the arm segment to enhance the power at the release of the bowl.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.1072-1076
• /
• 2001

A biomechanical study was conducted in this study to investigate if in-line skating wrist guards can effectively reduce the impact forces so as to protect the wrist from fracture. The forearm specimens with and without wrist guards were dropped using a specially designed sled to simulate the impact on the wrist while falling. A force plate was used to measure the total impact force on the dropping weight whereas a load cell was attached to the proximal end of the specimen and used to quantify the impact transmitted through the wrist joint. From the non-destructive tests, mean peak force measured from a force plate showed no difference between the guarded and unguarded groups whereas mean impulse of the guarded group was significantly greater than that of the unguarded group (p<0.01). Comparing the peak force and impulse measured from the load cell, the peak force of the guarded group was significantly less than that of the unguarded group (p<0.001), while the impulse values were similar. When the specimens were dropped from a higher position (2.5ft ve. 1ft), all unguarded specimens had severe wrist fractures whereas fracture was found in three out of 5 guarded specimens. Comparison of mean peak forces and impulses showed as significant difference between the guarded and unguarded groups only in the mean impulse measured from the force plate. These results suggest that the wrist guard may protect the wrist by attenuating the peak force transmitted to radius and ulnar although it may not be effective when the wrist is subjected to an impact sufficiently large to cause fractures.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.957-966
• /
• 1996

An attempt was made to measure the availability of waste heat, released from the cooling system of a small engine, which can be utilized for grain drying. An engine powered flat-bed rough rice dryer was constructed and the performance of the dryer with available engine-waste heat was analyzed for 10 , 20, 30 and 40 cm rough rice bulk depths with a constant dryer base area of 0.81$m^2$/min. The waste heat was sufficient to increase the drying air temperature 7 to 12$^{\circ}C$ at an air flow rate of 8.8 to 5.7㎥/min, while the average ambient temperature and relative humidity were 24$^{\circ}C$ and 70%. The minimum energy requirement was 3.26 MJ/kg of water removed in drying a 40 cm deep grain bed in 14h. A forty to fifty centimeter deep grained seems to be optimum in order to avoid over-drying in the top layers. On the basis of minimum energy requirement (3.26 MJ/kg ) , an estimation was made that the waste heat harvest from an engine of a power range of 1 to 10.5PS can dry about 0.1 to 1 metric on of rough rice from 23% to 15% m.c. (w.b) in 12 h at an average ambient temperature and relative humidity of $25^{\circ}C$ and 80%, respectively. The engine-waste heated grain dryer can be used in the rural areas of non industrialized countries where electricity is not available.

• Journal of Biomedical Engineering Research
• /
• v.34 no.2
• /
• pp.80-90
• /
• 2013

Recently, functional insoles of wedge-type it is for the young to raise their height inserted between insole and heel cause foot pain and disease. Additionally, these have a problem with stability and excessively load-bearing during gait like high-heel shoes. In this study, we compared the changes in biomechanical characteristics of foot with different insole thickness then we will utilize for the development of the insole with the purpose of relieving the pain and disease. Subjects(male, n = 6) measured COP(center of pressure) and PCP(peak contact pressure) on the treadmill(140cm/s) using F-scan system and different insole thickness(0~50 mm) between sole and plantar surface during gait. Also, we computed changes of stresses at the foot using finite element model with various insole thickness during toe-off phase. COP moved anterior and medial direction and, PCP was increased at medial forefoot surface, $1^{st}$ and $2^{nd}$ metatarsophalangeal, ($9%{\uparrow}$) with thicker insoles and it was show sensitive increment as the insole thickness was increased from 40 mm to 50 mm. Change of the stress at the soft-tissue of plantar surface, $1^{st}$ metatarsal head represents rapid growth($36%{\uparrow}$). Also, lateral moments were increased over the 100% near the $1^{st}$ metatarsal as the insole thickness was increased from 0 mm to 30 mm. And it is show sensitive increment as the insole thickness changed 10 mm to 20 mm. As a result, it was expected that use of excessively thick insoles might cause unwanted foot pain at the forefoot region. Therefore, insole thickness under 30 mm was selected.

• Korean Journal of Applied Biomechanics
• /
• v.19 no.1
• /
• pp.87-98
• /
• 2009

This study was conducted to compare biomechanical differences in throwing movement between skilled and unskilled high school students using three-dimensional analysis system with a force platform. The findings indicated that skilled students showed shorter throwing time, faster horizontal speed of (1) the center of mass at heel contact of left foot, (2) the forearm throughout swing phase, (3) the hand after heel contact while unskilled students showed faster horizontal speed of, (1) the center of mass after heel contact and (2) the hand at heel contact of left foot. Skilled students showed greater (1) shoulder angle during throwing, (2) elbow angle after take off of foot, (3) peak vertical ground reaction force during throwing and (4) peak anterior-posterior ground reaction force at heel contact of right foot. While skilled students showed leaning backward of the trunk during throwing, unskilled students showed leaning forward during release phase with leaning backward before release.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1391-1398
• /
• 2011

Biomechanical analysis of arm motion during steering was performed using a motion analysis technique. Three-dimensional position data for each part of arm are fed into an interactive model combining a musculoskeletal arm model and the mechanical steering system to calculate joint angles and torques using inverse kinematic and dynamic analyses, respectively. The analysis shows that elbow pronation/supination, wrist flexion/extension, shoulder adduction/abduction, and shoulder flexion/extension have significant magnitudes. Sensitivity analysis of the arm joint motion with respect to seating posture and steering wheel configuration is carried out to investigate the qualitative influence of the seating posture and driver's seat configuration on the steering behavior.

• Proceedings of the KOSOMBE Conference
• /
• v.1995 no.05
• /
• pp.19-22
• /
• 1995

A biomechanical study was made to demonstrate the superior mechanical performance of the newly designed Miniplate staple to the conventional Coventry staple in high tibial osteotomy(HTO). Using twenty fresh porcine tibiae, the fixational strengh of the two different types of staple in HTO was compared. To minimize the error due to the specimen-to-specimen individuality, the bone mineral density of the tibiae was measured with a bone densitometry (Dual photon absorptionometer, Luner, USA) and those with $0.8\;{\sim}\;1.2\;gm/cm^2$ at the proximal tibia was used in the biomechanical test. Testing was performed on a material testing system (Autogram ET-5, Shimatzu, Japan) with aid of a commercial data processor (IBM 80386/ ASYST). Using two differant loading modes, 'pull-out' and 'push-out', the maximum resistant force required to release the staple from the substrate bone was recorded. In the pull-out test, ten non-osteotomized specimens were used and the staple was pullout by subjecting an axial tension on the head of the staple inserted. While in the pull-out test where ten tibiae osteotomized in the usual way of HTO were used, the staple was not directly loaded. In this testing, as a mimic condition of the natural knee, the distal part of the specimen tibia was pushed horizontally in order for the staple to be pulled out while the proximal tibia was fixed. The pull-out strength of Coventry staple and miniplate staple were found to be $27.88\;{\pm}\;5.12\;kgf$ and $182.47\;{\pm}\;32.75\;kgf$, respectively. The push-out strength of Coventry staple and miniplate staple were $18.40\;{\pm}\;4.47\;kgf$ and $119.95\;{\pm}\;19.06\;kgf$, respectively. The result revealed that miniplate staple had the pull-out/ push-out strength at least fivetimes higher than Coventry staple. Based on the measured data, it was believed that the newly designed miniplate staple could provide much better postoperative fixation in HTO. The postoerative application of long leg casting may not be needed after HTO surgery.

• Journal of the Ergonomics Society of Korea
• /
• v.33 no.1
• /
• pp.15-25
• /
• 2014

Objective: This study aims to analyze the factors that affect the ability to maintain dynamic sitting balance (DSB), biomechanical characteristics, and physical characteristics in spinal cord injuries (SCI) patients. Background: Virtual ski training systems, ski equipment, and training protocols for disabled skiers are being studied to spread awareness. However, few studies have been reported on the sitting balance ability associated with chair mono skiing. Method: A dynamic sitting balance border system was built to investigate the ability to maintain dynamic sitting balance in SCI patients. Trunk muscle activity was evaluated by electromyogram while conducting dynamic sitting balance tests. The trunk muscle strength was tested with a portable handheld dynamometer. Physical activity scores were measured with the physical activity recall assessment. Results: There were high levels of correlation between the ability to maintain DSB and trunk flexor strength, extensor strength, rotator strength, and physical activity score. However, height, weight, and injury level in SCI patients were not correlated with the ability to maintain DSB. Additionally, strong negative correlations were found between muscle activities of the external oblique and lumbar erector spinae muscles and the ability to perform the backward tilt test. Trunk extensor muscle activity during the ball lifting test was significantly higher than in other tests. Conclusion: The results indicate that improving trunk muscle strength and physical activity can increase the ability to maintain DSB. Application: The findings of a close relationship between trunk strength, physical activity, and the ability to maintain DSB need to be reflected in the chair mono ski training program.