• 한국재료학회지
• /
• 제31권7호
• /
• pp.397-402
• /
• 2021

In this study, binderless-WC, WC-6 wt%Co, WC-6wt% 1 and 2.5 B₄C materials are fabricated by spark plasma sintering process (SPS process). Each fabricated WC material is almost completely dense, with a relative density up to 99.5 % after the simultaneous application of pressure of 60 MPa. The WC added Co and Co-B₄C materials resulted in crystalline growth. The WC with HCP crystal structure has respective interfacial energy (basal facet direction: 1.07 ~ 1.34 J·m^-2, prismatic direction: 1.43 ~ 3.02 J·m^-2) that depends on the grain growth direction. It is confirmed that the continuous grain growth, biased by the basal facet, which has relatively low energy, is promoted at the WC/Co interface. As abnormal grain growth takes place, the grain size increases more than twice from 0.37 to 0.8 um. It is found through analysis that the hardness property also greatly decreases from about 2661.4 to 1721.4 kg/mm², along with the grain growth.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2003년도 international symposium on advanced powder metallurgy
• /
• pp.43-43
• /
• 2003

• Nuclear Engineering and Technology
• /
• 제52권6호
• /
• pp.1243-1251
• /
• 2020

Irradiation-induced damage of binderless nanoporous-isotropic graphite (NPIG) prepared by isostatic pressing of mesophase carbon microspheres for molten salt reactor was investigated by 3.0 MeV He⁺ irradiation at room temperature and high temperature of 600 ℃, and IG-110 was used as the comparation. SEM, TEM, X-ray diffraction and Raman spectrum are used to characterize the irradiation effect and the influence of temperature on graphite radiation damage. After irradiation at room temperature, the surface morphology is rougher, the increase of defect clusters makes atom flour bend, the layer spacing increases, and the catalytic graphitization phenomenon of NPIG is observed. However, the density of defects in high temperature environment decreases and other changes are not obvious. Mechanical properties also change due to changes in defects. In addition, SEM and Raman spectra of the cross section show that cracks appear in the depth range of the maximum irradiation dose, and the defect density increases with the increase of irradiation dose.

• 자원리싸이클링
• /
• 제18권1호
• /
• pp.38-43
• /
• 2009

본 고에서는 현행 고순도 폴리실리콘 제조공정에서 부산물로 발생하고 있는 실리콘 미세분말을 경제적인 가격에 태양전지급 원료로 재이용하고자 실리콘 미세분말의 무점결제 성형공정에 대한 연구를 수행하였다. 폴리실리콘 미세분말의 평균 크기는 $7.8{\mu}m$였으며, 주요 불순물은 표면 산화물과 수분이었다. 표면 산화물을 제거하기 위한 HF수용액-에탄올 혼합용액을 이용한 전처리공정을 행함으로써 폴리실리콘 분말의 성형성 그리고 성형체의 밀도 및 강도를 향상시킬 수 있었다. 진공 중에서 성형하는 경우 성형체 회수율이 20%증가하였다. 폴리실리콘 미세 분말은 공정 부산물 상태에서는 태양전지용 원료로 사용되기에 적합한 순도가 아니었지만, 건식 열처리를 행함으로써 태양전지급 이상의 순도를 확보할 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제46권2호
• /
• pp.132-142
• /
• 2018

An elephant digests only around 30~45% of what it consumes; therefore the undigested material mainly passes as intact fibres. Elephant food is usually composed of grass, leaves, twigs, bark, fruit and seed pods. This research aimed to utilize the elephant dung fibers as material for composite board and citric acid as a bonding agent. Citric acid contents in this research were set at 0 wt% (binderless composite board), 10 wt%, 20 wt%, and 30 wt% based on dry weight particles, while the target density was set at $0.8g/cm^3$. Pressing temperatures were set at $180^{\circ}C$ and $200^{\circ}C$ with the pressing time was 10 minutes. Physical and mechanical properties tests were then performed according to Japanese Industrial Standard A 5905. The result showed that elephant dung fibers could be used as potential materials for composite board. Addition of citric acid and pressing temperature significantly increased the quality of composite board. Infrared analysis indicated that the presence of ester linkages much higher with the increasing of citric acid content and pressing temperature. The optimum properties of composite board made from elephant dung fibers could be achieved at pressing temperature of $200^{\circ}C$ and a citric acid content of 20 wt%.