• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2002년도 추계학술발표회
• /
• pp.187-190
• /
• 2002

Reductive dechlorination of endosulfans was studied with zero valent metals (ZVMs) and bimetals in aqueous batch reactors. The effect of surfactants was evaluated. Endosulfan was successfully dechlorinated with zero valent iron. However, a bimetal, palladium coated iron (Pd/Fe) showed a highly enhanced reactivity for both endosulfan I and II indicating palladium act as a dechlorination catalyst on the iron. The effect of surfactants on degradation with ZVM has been very controvertible. Variable concentration of a nonionic surfactant, Triton X-100 and an anionic surfactant, SDS were added into the reactor with ZVM. The reaction rates of endosulfan were increased with both surfactants. In the case of Triton X-100, the reaction rate was increased with the increasing surfactant concentration up to 400 mg/L. Addition of small amount of surfactant under the CMC, the reaction rate was increased. However, the enhancing effect was diminished when a higher concentration of surfactant (1,000 mg/L) was used. Current study implicate that the surfactant adsorbed on the metal surface might increase the surface concentration of endosulfan resulting in the increased reaction rate. However, partitioning of endosulfan into the micelle formed at the high concentration of surfactant diminish the enhancing effect by reducing the contact chance between target compound and the metal surface.

• 한국전기전자재료학회논문지
• /
• 제19권3호
• /
• pp.250-254
• /
• 2006

Hetero-junction sheet actuator composed of carbon nanotubes and $V_{2}O_5$ nanowires were demonstrated in a bimetal configuration. The successive filtration of $V_{2}O_5$ nanowire solution followed by carbon nanotube dispersed water solution in the same way produced a dark-gray colored sheet. A significant actuation was observed in sodium chloride electrolyte solution with a bending direction to the carbon nanotube side at the positive bias voltage against the copper counter-electrode. As the frequency of the applied voltage increased, the amplitudes decreased, indicating a rather slow response of the hetero-film actuator in the electrolyte solution. The hybrid structure enabled an easy fabrication of the film actuator with the enhanced efficiencies.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.40-48
• /
• 2001

An ultrasonic test method, as a nondestructive test is applied to ensure the clad interface quality assessment. According to the reference codes and standards, not only korea Industrial Standard(KS) but also American Society for Testing and Materials (ASTM) Standard, ultrasonic examination procedures use the pulse-echo, A-scan, back reflection signal drop method and/or side drilled reference hole used to establish the acceptance criteria of clad material test. But the variety of bonding materials and sizes makes it difficult to produce the reference blocks, or thus the criteria. In order to overcome these practical difficulties, new ultrasonic testing criterion is suggested. In this new method, the theoretical interface reflection signal amplitude level is calculated and suggested as an acceptance criteria with the back reflection signal set to 100% FSH(Full Screen Height) which is based on acoustic impedance mismatch at the clad interface for the explosive clad ultrasonic inspection. Applicability of suggested criterion, for the explosive clad Fe-Naval Brass with different bonding quality is confirmed to the pre-existed KS and ASTM specifications and verified by using SEM (Seanning Electron Microscope) micrograph. The results obtained by the suggested method is more conservative than the results according to the KS B 0234 and ASTM A 578 specifications The suggested method could be applicable to any other combination of explosive clad ultrasonic inspection.

• 공업화학
• /
• 제18권5호
• /
• pp.459-466
• /
• 2007

본 연구에서는 다양한 금속들이 담지된 H형 베타 제올라이트(BEA)를 황성분 함유 부취제 제거용 흡착제로 활용하였다. 단일 금속이 담지되거나 또는 두 종류의 금속이 복합적으로 함유된 여러 종류의 흡착제를 사용하여 연속적인 흡착층에서 THT와 TBM 부취제에 대한 개별적 혹은 경쟁적인 흡착 특성을 평가하였다. 순수한 H형 BEA 제올라이트는 TBM 화합물에 대하여 가장 높은 흡착능력을 나타내었으며, THT 부취제는 Fe, Pd 금속 및 ZnO를 함유한 HBEA상에서 더 많은 양으로 흡착 제거되었다. 복합금속함유 흡착제의 경우에는 Cu-Zn/HBEA와 Fe-Mo/HBEA가 TBM 부취제에 대하여 더 높은 흡착용량을 나타내었다.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.31-37
• /
• 2016

In the steam system, a stream trap valve discharges a condensate and a non-condensable gas. It also prevents stream from being leaked. The free float stream trap valve is a mechanical type of stream trap. The valve is opened when a hallow ball is floated due to the density of the condensate through the condensate flows into the valve. On the other hand, when the flow of the condensate is completed, the valve is closed as the float subsides due to the weight of the structure and the stream is blocked. In addition, the bimetal lifts the hallow ball, which discharges the non-condensable gas. In this study, the performance of the properties of the free float stream trap valve, the method of support for three points, and the orifice design are researched. Moreover, the condensate discharge capacity of the free float stream trap valve is calculated from the experiment.

• 한국수소및신에너지학회논문집
• /
• 제30권6호
• /
• pp.549-555
• /
• 2019

Electrocatalysis of oxygen reduction reaction (ORR) using Pt nanoparticles or bimetal on carabon was studied. Currently, the best catalyst is platinum, which is a limited resource and expensive to commercialize. In this paper, we investigated the cheaper and more active electrocatalysts by making Pt nanoparticles and adding 3D transition metal such as copper. Electrocatalysts were obtained by chemical reduction based on ethylene glycol solutions. Elemental analysis and particle size were confirmed by XRD and TEM. The electrochemical surface area (ECSA) and activity of the catalyst were determined by electrochemical techniques such as cyclic voltammetry and linear sweep voltammetry method. The commercialized Pt support on carbon (Pt/C, JM), synthesis Pt/C and synthesis Pt3Cu1 alloy nanoparticles supported on carbon were compared. We confirmed that the synthesized Pt3-Cu1/C has high electrochemical performance than commercial Pt/C. It is expected to develop an electrocatalyst with high activity at low price by increasing the oxygen reduction reaction rate of the fuel cell.

• 대한금속재료학회지
• /
• 제47권8호
• /
• pp.461-465
• /
• 2009

We study the diffusion of Ag based bimetallic nanoclusters supported on graphite. Using a molecular dynamics simulation, we reveal that the Ag clusters show rapid diffusion because of their hexagonal bottom layer. In order to decrease the rate of diffusion, we added Pt and Ni to distort the structure of the alloy cluster (i.e., the alloying method). We expected Pt to provide a stronger force on Ag atoms, and Ni to shorten the bond length and thereby change the structure of Ag cluster. However, the attempt was unsuccessful, because Pt and Ni atoms formed cores inside the Ag clusters. We therefore designed a collision system where large Ag clusters collide with small Pt or Ni clusters. Upon collision with Pt clusters, the diffusion showed little change, because Pt atoms are substituted at the Ag atomic site and form a perfectly ordered structure. The collision with Ni, however, deforms the bottom layer as well as the overall cluster structure and decreases diffusion. This outcome appoints toward the possibility of further application to the manufacture of durable nanocatalysts.

• 소성∙가공
• /
• 제16권7호
• /
• pp.530-537
• /
• 2007

This paper is concerned with the analysis of plastic deformation of bimetal co-extrusion process. Two sets of material combination have been adopted for analysis, i.e. combinations of Cu/Al and Fe/Al. In the first set of material combination, the selected materials are AA 1100 aluminum alloy as hard material and CDA 110 as soft one. This type of material selection is to examine the effect of hard core and soft sleeve and vice versa on the deformation pattern in terms of plastic zone and velocity discontinuity along the contact surface between construction materials. Four different cases of co-extrusion process in terms of material combination and interference bonding were simulated to investigate the effect of material arrangement between core and sleeve, and of bonding on the plastic zones and velocity discontinuity. In the other set of material combination, model materials used as core and sleeve were AA 1100 and AISI 1010, which are relatively soft and hard, respectively. Process parameters except diameter ratio of core to sleeve material such as semi-die angle, reduction in area in global sense and die comer radius have been set constant throughout the simulation to concentrate our effort on the analysis of influence of diameter ratio on deformation behavior such as deformation zone, surface expansion, exit velocity discontinuity between composite materials, and extrusion forces.

• 한국전자통신학회논문지
• /
• 제10권8호
• /
• pp.921-926
• /
• 2015

멀티 콘센트의 과전류로 인한 과열을 방지하기 위한 보호방식으로는 주로 금속바이메탈 방식, 스위칭회로 방식, 마이크로컨트롤러(MCU)를 이용한 과전류 정밀제어 방식 등이 사용되어 오고 있다. 하지만 이러한 방식들은 보호회로가 과전류가 흐르는 전선에 병렬접속 함으로써 2차 화재의 위험이 있을 수 있으며 입력전압의 비선형 왜곡에 취약한 단점을 가지고 있다. 또한 기존의 방식들은 제품의 단가가 비교적 크게 올라가므로 충분한 시장성을 확보하기가 쉽지 않다. 본 논문에서는 이러한 문제를 해결하고자 과전류가 흐르는 전선에 비접촉식 관통형 변류기를 설계하고 변류기의 2차 유도전류를 이용하여 과전류를 감지하여 사용자가 과전류 상황을 인지할 수 있도록 LED 및 부저 회로를 통하여 시각 및 청각적 신호를 전달하는 기능을 구현한다. 실험 결과들로부터 제안된 회로는 매우 경제적이고 간단하면서도 안정적으로 동작함을 확인 할 수 있다.

• 한국가스학회지
• /
• 제5권1호
• /
• pp.15-20
• /
• 2001

저온 마이크로웨이브 플라즈마와 촉매반응에 의한 메탄올 활성화하여 C2+ 화합물과 수소로 전환하는 반응을 고찰하였다. 금속 촉매인 Fe, Ni과 귀금속 촉매인 Pt, Pd 계열의 촉매로 본 실험을 수행하였다 메탄의 유속이 $20ml\;min^{-1}$일때 플라즈마의 출력이 증가할수록 C2+ 생성물은 29에서 $42\%$로 증가하였으며 동시에 메탄의 커플링 반응에서 발생하는 수소는 0.6에서 0.65 몰분율을 나타내었다. 촉매는 플라즈마 영역 후단에 위치하였을 때, C2+ 생성물이 일정한 수율을 나타내는 반면 에틸렌과 아세틸렌의 선택도는 향상되었다. 플라즈마 반응후 ECR 전기장과 Pd-Ni 이원촉매를 위치했을 때 최고의 C2+ 수율은 $64\%$로 관찰되었다.