• Journal of Sensor Science and Technology
• /
• v.21 no.3
• /
• pp.198-203
• /
• 2012

In this paper, the driving information system of the bicycle has been studied by using the 3-axis acceleration sensor. The sensor module composed of 3-axis acceleration sensor and MCU(Microcontroller Unit) was mounted onto the handle of bicycle and the experiments were conducted on the flatland, uphill and downhill of bicycle road. Three axis acceleration values were converted to the pitch and roll angles, then four major compensation methods have been applied to achieve meaningful data for driving information system. The experimental results of pitch angles showed 2.46, -1.26, 7.79 degrees in case of flatland, uphill, downhill, respectively. When the steering handle turned to the left direction, roll angles showed -29.35, -41.67, -36.98 degrees at each road condition. With the right-turn, roll angles presented 20.05, 33.75, 24.44 degrees in case of flatland, uphill, and downhill, respectively. The pitch angle has been increased more than 40 degrees at stop mode. By using the change of pitch and roll angles, we could obtain the driving information system of bicycle successfully.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.6
• /
• pp.532-539
• /
• 2012

This paper proposes a balancing and driving control system for a bicycle robot. A reaction wheel pendulum control method is adopted to maintain the balance while the bicycle robot is driving. For the driving control, PID control algorithm with a variable gain adjustment has been developed in this paper, where the gains are heuristically adjusted during the experiments. To measure the angles of the wheels the encoders are used. For the balancing control, a roll controller is designed with a non-model based algorithm to make the shortest cycle. The tilt angle is measured by the fusion of the acceleration and gyroscope sensors, which is used to generate the control input of the roll controller to make the tilt angle zero. The performance of the designed control system has been verified through the real experiments with the developed bicycle robot.

• International Journal of Highway Engineering
• /
• v.14 no.4
• /
• pp.103-111
• /
• 2012

PURPOSES : Effective speed management is necessary for preventing traffic crashes on the road. Speed hump is known as an effective tool for managing speed. Unlike existing studies which are mainly focused on humps for vehicles, this study proposed a novel method to determine design parameters for bicycle speed humps based on a multi-criteria decision making process. METHODS : Three objectives including the effectiveness of speed reduction, bicycle safety, and user's comfortability were incorporated into the proposed evaluation framework for determining design parameters. A multi-criteria value function was also derived and utilized as a part of the proposed method. RESULTS : Extensive simulations and statistical tests show that an integrated bike-box way is identified as the best in terms of operational efficiency and safety. CONCLUSIONS : It is expected that the outcomes of this study can be a valuable precursor for developing design guidelines for bicycle road and facility.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1103-1108
• /
• 2007

This paper describes a robust model-based roll state estimator for application to the detection of impending vehicle rollover. The roll state estimator is based on a 2-D bicycle model and a roll model to estimate the maneuver-induced vehicle roll motion. The measurement signals are lateral acceleration, yaw rate, steering angle, and vehicle speed. Vehicle mass is adapted to obtain robust performance of the estimator. Computer simulation is conducted to evaluate the proposed roll state estimator by using a validated vehicle simulator. It is shown that the roll state estimator shows robust performance without exact vehicle mass information.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1132-1137
• /
• 2007

This paper describes a Unified Chassis Control (UCC) strategy to prevent vehicle rollover by integrating individual modular chassis control systems such as Electronic Stability Control (ESC) and Continuous Damping Control (CDC). The UCC threshold is determined from a rollover index computed by estimated roll angle, roll rate and measured lateral acceleration. A direct yaw moment control method is used to design the ESC based on a 2-D bicycle model. Similarly, the CDC is designed based on a 2-D roll model using a direct roll moment control method. The performance of the proposed UCC scheme is investigated and compared to that of modular chassis controllers through computer simulations using a validated vehicle simulator. It is shown that the proposed the UCC can lead to improvements in vehicle stability and efficient actuation of chassis control systems.

• International Journal of Automotive Technology
• /
• v.7 no.7
• /
• pp.821-826
• /
• 2006

This paper describes a rollover index (RI)-based rollover mitigation control (RMC) system. A rollover index which indicates an impending rollover has been developed by a roll dynamics phase plane analysis. The rollover index is calculated using the roll angle, the roll rate, the lateral acceleration and time to wheel lift (TTWL). A differential braking control law based on a 2-D bicycle model has been designed using the direct yaw control (DYC) method. An RMC threshold has been determined from the rollover index. The performance of the RMC scheme and the effectiveness of the proposed rollover index are illustrated using a vehicle simulator.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1126-1131
• /
• 2007

This paper presents unified chassis control (UCC) to improve the vehicle lateral stability. The unified chassis control implies combined control of active front steering (AFS), electronic stability control (ESC) and continuous damping control (CDC). A direct yaw moment controller based on a 2-D bicycle model is designed by using sliding mode control law. A direct roll moment controller based on a 2-D roll model is designed. The computed direct yaw moment and the direct roll moment are generated by AFS, ESP and CDC control modules respectively. A control authority of the AFS and the ESC is determined by tire slip angle. Computer simulation is conducted to evaluate the proposed integrated chassis controller by using the Matlab, simulink and the validated vehicle simulator. From the simulation results, it is shown that the proposed unified chassis control can provide with improved performance over the modular chassis control.