• Structural Engineering and Mechanics
• /
• v.61 no.1
• /
• pp.161-169
• /
• 2017

This study aimed to develop a simple and effective method to facilitate the experimental research on mechanical properties of masonry under biaxial compressive stress. A series of tests on full-scale brick masonry panels under biaxial compression have been performed in limited principal stress ratios oriented at various angles to the bed joints. Failure modes of tested panels were observed and failure features were analyzed to reveal the mechanical behavior of masonry under biaxial compression. Based on the experimental data, the failure curve in terms of two orthotropic principal stresses has been presented and the failure criterion of brick masonry in the form of the tensor polynomial has been established, which indicate that the anisotropy for masonry is closely related to the difference of applied stress as well as the orientation of bed joints. Further, compared with previous failure curves and criteria for masonry, it can be found that the relative strength of mortar and block has a considerable effect on the degree of anisotropy for masonry. The test results demonstrate the validity of the proposed experimental method for the approximation of masonry failure under biaxial compressive stress and provide valuable information used to establish experimentally based methodologies for the improvement of masonry failure criteria.

• Journal of the Korean Magnetics Society
• /
• v.21 no.1
• /
• pp.10-14
• /
• 2011

We have measured the ferromagnetic resonance (FMR) signal in as deposited and $400^{\circ}C$ annealed CoFeB/MgO thin film to investigate the annealing effect on magnetic anisotropies and FMR linewidth (${\Delta}H_{PP}$). The uniaxial anisotropy field ($H_{K1}$) was only observed in the as deposited sample. Whereas, in the $400^{\circ}C$ annealed sample, the biaxial anisotropy field ($H_{K2}$) was additionally observed in accompany with uniaxial anisotropy field ($H_{K1}$). The appearance of biaxial anisotropy fields was originated from the crystalline growth of bcc CoFeB(001) from the MgO(001) interface and by the B diffusion during thermal annealing. Also, the ${\Delta}H_{PP}$ of $400^{\circ}C$ annealed sample was increased compared with that of as deposited sample, which was due to the broad distribution of the magnetization axis by the biaxial anisotropy.

• Computers and Concrete
• /
• v.5 no.4
• /
• pp.417-434
• /
• 2008

This paper deals with damage induced anisotropy modeling for concrete-like materials. A thermodynamics based constitutive relationship is presented coupling anisotropic damage and elasticity, the main idea of the model being that damage anisotropy is responsible for the dissymmetry tension/compression. A strain written damage criterion is considered (Mazars criterion extended to anisotropy in the initial model). The biaxial behavior of a family of anisotropic damage model is analyzed through the effects of yield surface modifications by the introduction of new equivalent strains.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.3
• /
• pp.209-212
• /
• 2012

In this paper, we have studied on the optimal design of the optical compensation film for the TN-LCDs. To have wide viewing angle panels, several methods such as multi-domain method, optical path method, and phase compensation method have been proposed. Among these methods, this paper focused on the phase compensation method. In the phase compensation method, the phase retardation generated from the optical birefringence for the off-axis incident is compensated by using optical films with refractive anisotropy. To compensate the phase retardation of the TN-LCDs, we have proposed design concept for the biaxial optical films and analyzed the optical performance for the proposed structures. The calculation of the dynamic motion of the liquid crystals was based on the Ericksen-Leslie theory and the optical performance of the TN-LCD was calculated from the Extended Jones Matrix Method. From the results, we have confirmed that the optical characteristics of the TN-LCDs with the biaxial films have been improved considerably compared with the TN-LCDs compensated by the combination of the uniaxial films.

• Journal of the Korean Magnetics Society
• /
• v.18 no.4
• /
• pp.147-153
• /
• 2008

It has been well-known that the Fe/GaAs heterostructure has a small lattice mismatch of 1.4% between Fe and GaAs, and the Fe layer is grown epitaxially on the the GaAs substrate. There are rich physics are observed in the GaAs/Fe interface, and the spininjection is actively studied due to its potential applications for spintronics devices. We fabricated Fe wedge layer in the thickness range $0{\sim}3.4$ nm on the GaAs(100) surface with 5-nm thick Au capping layer. The magnetic anisotropy of the Fe/GaAs system was investigated by employing Brillouin light scattering(BLS) measurements in this study. The spin wave excitation of Fe layer was studied as the function of intensity and the in-plane angle of external magnetic field, and thickness of Fe layer. Also these various dependences were analyzed with analytic expression of spin wave surface mode in order to determine the magnetic anisotropies. It has been found that the GaAs/Fe/Au system has additional uniaxial magnetic anisotropy, while the bulk Fe has biaxial anisotropy. The uniaxial anisotropy shows increasing dependency respected to decreasing thickness of Fe layer while biaxial anisotropy is reduced with Fe film thickness. This result allows the analysis that the uniaxial anisotropy is originated from interface between GaAs surface and Fe layer.

• Applied Science and Convergence Technology
• /
• v.23 no.5
• /
• pp.273-278
• /
• 2014

Using ab initio calculations, the effects of uniaxial, biaxial, and hydrostatic strains on the magnetocrystalline anisotropy of $L1_0$-orderd FePt and CoPt alloys were systematically investigated. Interestingly, the rates and the signs of magnetocrystalline anisotropy changes of FePt and CoPt were determined by the directions and dimensions of strains. The calculation results are consistent with the previous experimental observations and are expected to provide directions to tailor magnetic properties of various types of $L1_0$-ordered FePt and CoPt systems.

• Journal of the Korean Magnetics Society
• /
• v.21 no.3
• /
• pp.83-87
• /
• 2011

We have analyzed the torque signals measured in synthetic antiferromagnetic (SAF) coupled CoFeB/Ru/CoFeB thin film, which signals were drastically changed at flopping field ($H_F$) and saturation field ($H_s$). The minimum value of negative uniaxial anisotropy constant ($-\;K_1$) was appeared at HF. The $-\;K_1$ was due to the zero net magnetization by the antiferromagnetic coupling between two ferromagnetic layers. Whereas, the biaxial anisotropy constant (K2) was induced in the field range of $H_F$ < H < $H_s$. The induced $K_2$ was originated from deviation angles between magnetization directions of two ferromagnetic layers. And at H > $H_s$, intrinsic uniaxial anisotropy constant of CoFeB layer was observed. These change of the anisotropy constant with magnetic field was explained by the magnetization process of two ferromagnetic layers based on Stoner-Wohlfarth model calculation for SAF thin film.

• Journal of the Korea Concrete Institute
• /
• v.15 no.1
• /
• pp.125-133
• /
• 2003

• Journal of Powder Materials
• /
• v.18 no.2
• /
• pp.168-171
• /
• 2011

We investigate grain growth behavior of poly-crystalline Mg sheet having strong basal fiber texture using phase field model for grain growth and micro-elasticity. Strong initial basal texture was maintained when external load was not imposed, but was weaken when external biaxial strain was imposed. Elastic interaction between elastic anisotropy of Mg grain and external load is the reason why texture evolution occurs.

• Tunnel and Underground Space
• /
• v.12 no.4
• /
• pp.237-247
• /
• 2002

A total of 18 stress measurements were performed in the rock and rock-like blocks in the laboratory to estimate the influence of anisotropy in rock. Full scale overcoring equipment, which consists of a coring machine and a biaxial loading system by flat jacks, was developed to simulate the in-situ rock stress condition in the laboratory By comparing the isotropic analysis with the anisotropic analysis in measuring the stress, conclusions have been drawn as to the influence of anisotropy. The maximum difference between the isotropic and the anisotropic analysis was 34% and it was shown that the stress measurement considering the anisotropy was needed. To confirm the validity of the observed data, a diagnostic analysis of stress relief curve by overcoring was conducted using the three dimensional finite difference program, FLAC 3D.