• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.102-103
• /
• 1994

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.2
• /
• pp.222-227
• /
• 2009

The bias characteristics due to the changes of temperature and temperature gradient of fiber coil are investigated in fiber-optic gyroscope. The bias performance is degraded with the changes of temperature and temperature gradient of fiber coil. The temperature compensation using both the temperature-dependent bias measurement and the temperature-induced error model of fiber-optic gyroscope improves the bias stability about 3 times as much as the uncompensated original case, which leads to very stable bias performance over the temperature range from $-35^{\circ}C$ to $+77^{\circ}C$.

• ETRI Journal
• /
• v.31 no.1
• /
• pp.62-64
• /
• 2009

We report on the bias stability characteristics of transparent ZnO thin film transistors (TFTs) under visible light illumination. The transfer curve shows virtually no change under positive gate bias stress with light illumination, while it shows dramatic negative shifts under negative gate bias stress. The major mechanism of the bias stability under visible illumination of our ZnO TFTs is thought to be the charge trapping of photo-generated holes at the gate insulator and/or insulator/channel interface.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.177-181
• /
• 2009

Compositional gradient CrNx coatings were fabricated using arc ion plating in Ar/$N_2$ gaseous mixture by gradually increasing $N_2$ flux rate from 0 to 120 SCCM. The effect of negative substrate bias on the film microstructure and mechanical properties were systematically investigated with XRD, GDOES, and SEM. The results show that substrate bias has an important influence on film growth and microstructure of gradient CrNx coatings. The coatings mainly crystallized in the mixture of hexagonal $Cr_{2}N$ and fcc CrN phases. By increasing substrate bias, film microstructure evolved from an apparent columnar structure to an equiaxed one. With increasing substrate bias, deposition rate first increased, and then decreased. The maximum of deposition rate was 15 nm/min obtained at a bias of -50V.

• The Korean Journal of Ceramics
• /
• v.3 no.1
• /
• pp.13-17
• /
• 1997

It is identified that the diamond films grown o bias-treated (100) silicon showed different surface morphologies and film textures according to the initial applied dc bias voltage at the same growth condition. The highly oriented diamond film (HODF) was successfully grown on -200 V bias-treated silicon substrate in which the heteroepitaxial relation of $(100)_{dimond}//(100)_{si}\; and\; [110]_{diamond}//[110]_{si}$ was identified. On the contrary, the heteroepitaxial relation was considerably disturbed in the samples bias-voltage was a key factor in growing the highly oriented diamond film on (100) silicon substrate. Considering the experimental results, we proposed a new model about heteroepitaxial diamond growth on silicon, in which 9 diamond unit cell are matched with 4 silicon cells and the bond covalency of both atoms is satisfied via the intermediate layer at the interface as well.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1263-1268
• /
• 2008

In this paper, the low noise power amplifier for GaAs FET ATF-10136 is designed and fabricated with active bias circuit and self bias circuit. To supply most suitable voltage and current, active bias circuit is designed. Active biasing offers the advantage that variations in the pinch-off voltage($V_p$) and saturated drain current($I_{DSS}$) will not necessitate a change in either the source or drain resistor value for a given bias condition. The active bias network automatically sets a gate-source voltage($V_{gs}$) for the desired drain voltage and drain current. Using resistive decoupling circuits, a signal at low frequency is dissipated by a resistor. This design method increases the stability of the LNA, suitable for input stage matching and gate source bias. The LNA is fabricated on FR-4 substrate with active and self bias circuit, and integrated in aluminum housing. As a results, the characteristics of the active and self bias circuit LNA implemented more than 13 dB and 14 dB in gain, lower than 1 dB and 1.1 dB in noise figure, 1.7 and 1.8 input VSWR at normalized frequency $1.4{\sim}1.6$, respectively.

• Journal of Advanced Navigation Technology
• /
• v.13 no.3
• /
• pp.358-364
• /
• 2009

This paper shows some variable bias techniques which can improve the power added efficiency(PAE) for the designed power amplifier. Some simulations have been done to get the effect of the bias change, and variable bias is adopted to get the higher efficiency for dual mode amplifier which generates two different output power levels. With drain bias change and a fixed gate bias, the amplifier shows PAE improvement compared to the fixed bias amplifier. In addition, this paper analyzed nonlinear distortion of the power amplifier and has used the digital predistortion which can result in 10dB ACPR improvement for the dual band amplifier.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.1-6
• /
• 2007

A drain bias switching technique is presented to enhance power added efficiency for WiBro and wireless LAN dual band and dual mode transmitter. Some simulations have been done to predict the effect of drain and gate bias change, and bias switching is proposed to get the higher efficiency for dual mode transmitter which generates different output power for different applications. With drain bias switching and simulated optimum fixed gate bias, the amplifier shows dramatic PAE improvement compared to the amplifier without bias switching. The drain and gate bias switching technique will be useful for multi mode communication system with various functions.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.1
• /
• pp.6-11
• /
• 2004

The characteristics of interface layer and the effect of bias voltages on the nucleation density and heteroepitaxial growth of diamond films were studied in the hot filament CVD diamond process. Diamond films were deposited on a high speed steel (SKH-51) substrate by bias-assisted hot filament CVD technique with a titanium interlayer. The bias applied for enhancing the emission of electrons from the filament increased the nucleation density and achieving heteroepitaxial growth of CVD diamond. Diamond films obtained at a gas pressure of 20 torr; a bias voltage of 200 V and a substrate temperature of $700^{\circ}C$. Titanium was a suitable element as an interlayer for the diamond deposition on steel because it has high diffusivity of Fe and C as a carbide forming element.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.1
• /
• pp.5-12
• /
• 2004

The enhancement of adhesion for Cu film on polycarbonate (PC) surface with the $Ar/O_2$ gas plasma treatment and dc-bias sputtering was studied. The plasma treatment with this reactive mixture changes the chemical property of PC surface into hydrophllic one, which is shown by the variation of contact angle with surface modification. The micro surface roughness that also gives the high adhesive environment is increased by the $Ar/O_2$ gas plasma treatment. These results were observed distinctly from the atomic force microscopy (AFM). The negative substrate dc-bias effect for the Cu adhesion on PC was also investifated. Accelerated $Ar^{+}$ lons in sheath area of anode bombard the bare surface of PC during initial stage of dc bias sputtering. PC substrate. therefore, has severe roughen and hydrophilic surface due to the physical etching process with more activated functional group. As dc-bias sputtering process proceeds, morphology of Cu film shows better step coverage and dense layer. The results of peel test show the evidence of superiority of bias sputtering for the adhesion between metal Cu and PC.C.