• Journal of the Korean Wood Science and Technology
• /
• 제27권4호
• /
• pp.20-29
• /
• 1999

Temperature has important effect on mechanical properties of wood. These effect needs to be understood and taken into account in the structural use of wood. Furthermore, the effect of cooling after exposing to high temperature must be explained. In this study, the effect of temperature, exposure time, specific gravity, and cooling on bending properties were investigated. The boundary temperatures at which bending MOE and MOR reduced rapidly were approximately $200^{\circ}C$ and $150^{\circ}C$, respectively. This boundary temperature was nearly constant with independence of species(specific gravity), exposure time, and cooling. Above the boundary temperature, the effect of exposure time was increased with temperature and the reduction of bending MOE and MOR for Japanese Larch with relatively higher specific gravity was smaller than that of Hem-fir. The recovery of bending MOE and MOR after cooling was also more significant above the boundary temperature than below. The degree of cooling effect was larger for MOR than MOE. Consequently, bending properties of wood in elevated temperatures should be considered in terms of the boundary temperature, $200^{\circ}C$ for bending MOE, $150^{\circ}C$ for MOR, and these boundary temperatures must be considered an important factor. Furthermore, to evaluate the safety of structure, the recovery after cooling should be considered.

• 한국의류산업학회지
• /
• 제6권4호
• /
• pp.497-502
• /
• 2004

The mechanical properties of jean slacks to the type of cutting lines in knee region and the bending time, after doing bending 0 times, 500 times, and 1500 times, the effects of whether or not cutting line, the fabric direction of the cutting area, and the number of cutting lines were investigated for tensile, shearing, compression, and mixing value of mechanical properties. The results are as follows: EM to bending times were larger in order of weft

• 대한물리의학회지
• /
• 제9권4호
• /
• pp.425-432
• /
• 2014

PURPOSE: The purpose of this study was to investigate that the differences in sternocleidomastoid muscle activity, neck rotation angle, neck lateral bending angle and neck lateral bending onset time between conditions with and without visual biofeedback during neck rotation. METHODS: Ten male and four female adults with condition of forward head posture were recruited in this study. Subjects conducted to left and right maximal neck rotation under the conditions with and without visual biofeedback. During neck rotation, kinematic data of neck rotation, neck lateral bending movement, and electromyography activities of bilateral sternocleidomastold muscles were collected. Differences in dependent variables between conditions with and without visual biofeedback were analyzed using paired t-test. RESULTS: There were significant decreases in lateral bending angle, while lateral bending movement onset time was delayed significantly when applying visual biofeedback (p<.05). However, there were no significant differences in the activation of left and right sternocleidomastoid muscles and neck rotation angle between conditions with and without visual biofeedback (p>.05). CONCLUSION: These findings suggest that visual biofeedback may be effective for axial rotation of cervical spine during neck rotation in adults with forward head posture.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.62-68
• /
• 2000

In order to automate straightening process of deflected beams an adaptive three-point bending controller is studies which estimates and controls springback of beams under three-point bending. An analytical load-deflection model for three-point bending of beams with circular cross sections is derived nondimensionally. In spite of variation of material and process parameters this model can be applied to springback estimation by measuring real-time values of reactive load and deflection of the beam. A hydraulic punch stroke controller is designed to take real-time controls of the permanent deflection of the beam. The validity of the proposed system is verified through experiments.

• 한국해양공학회지
• /
• 제15권2호
• /
• pp.124-129
• /
• 2001

The research on anticorrosive of valve for ship, waterworks, and drainage system is very important. The purpose of this paper is to develop the metal/polyurethan adhesive technique at insider of the value to prevent corrosion in the value. It is performed to the bending strength test by using metal /polyurethan in the metals (SB41, Al6061). It is investigated to the effects of bending strength on curing temperature, preheating time and curing time, and to the fracture mechanism of metal/polyurethan adhensived specimen. As a results, we find that the bending strength is the highest at curing temperature of 11$0^{\circ}C$ and the curing time is 60 minutes in metal/polyurethan adhesive specimen.

• Design & Manufacturing
• /
• 제15권3호
• /
• pp.19-25
• /
• 2021

The bending process of a press die is to bend a flat blank to the required angle. There are V-bending, U-bending, Z-bending, O-bending etc. for bending processing, and the basic principle of calculating the unfolding length of die processing is used as the neutral plane length. Since the constant of the length value of the neutral surface is different depending on the type of bending, it is impossible to accurately calculate it. In particular, Z-bending processing is performed twice, and it is set on the upper and lower surfaces of the blank, and bending processing occurs at the same time as the upward and downward bending, and the elongation of the material occurs and the material increases. It is not possible to check with the calculated value, and it occurs in many cases where the mold is modified after start-up. This study aims to minimize die modification by developing a formula to calculate the development length of Z-bend.

• 펄프종이기술
• /
• 제36권2호
• /
• pp.39-46
• /
• 2004

In this paper, the effects of roll diameter and storage time in roll form, bending method and relative humidity on curl in copy paper and inkjet coated papers are investigated. In copy paper, more MD curl is showed at smaller roll diameter and the extension of bending time. However CD curl is hardly influenced by roll diameter and bending time. At high relative humidity, especially CD curl largely reduces. All inkjet coated papers without the primary or the secondary back coating during papermaking show the increase in MD curl and slight decrease in CD curl by MD bending regardless of the winding methods(TSO, TSI). The water spray as back coating results in the remarkable reduction of CD curl regardless of the winding methods. Drying on flat dryer after spraying the moisture on back side display the most excellent effect on the reduction of CD curl.

• 대한기계학회논문집A
• /
• 제25권7호
• /
• pp.1125-1130
• /
• 2001

Dynamic behaviors of an automatic dynamic balancer are analyzed by a theoretical approach. Using the polar coordinates, the non-linear equations of motion for an automatic dynamic balancer equipped in a rotor with the bending flexibility are derived from Lagrange equation. Based on the non-linear equation, the stability analysis is performed by using the perturbation method. The stability results are verified by computing dynamic response. The time responses are computed from the non-linear equations by using a time integration method. We also investigate the effect of the bending flexibility on the dynamics of the automatic dynamic balancer.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.629-634
• /
• 2000

Dynamic behavior of an automatic dynamic balancer is analyzed by a theoretical approach. Using Lagrange's equation, we derive the non-linear equations of motion for an automatic dynamic balancer equipped in a rotor with the bending flexibility with respect to the rectangular coordinate. Considering the rotor bending flexibility we analyze out-of-plane vibrations as well as in-plane vibrations of the automatic dynamic balaner. The time responses are computed from the non-linear equations by using a time integration method. We also investigate the effect of rotor flexibility on the behavior of the automatic dynamic balancer

• Current Optics and Photonics
• /
• 제1권6호
• /
• pp.618-625
• /
• 2017

In the present research, a new bending system using a segmented vacuum chuck for Stressed Mirror Polishing (SMP) is developed. SMP is a special fabrication method for thin aspheric mirrors, where simple flat or spherical fabrication is applied while a mirror blank is deflected. Since a mirror blank is usually glued to a bending fixture in the conventional SMP process, there are drawbacks such as long curing time, inconvenience of mirror replacement, risk of mirror breakage, and stress concentration near the glued area. To resolve the drawbacks, a new bending system is designed to effectively hold a mirror blank by vacuum. For the developed bending system, the optimal bending load to achieve the designated mirror deflection is found by finite element analysis and an optimization algorithm. With the measurement results of the deflected mirror surfaces with the optimal bending loads, the feasibility of the developed bending system is investigated. As a result, it is shown that the bending system is appropriate for the SMP process.