• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.46-57
• /
• 2006

To estimate nondestructively strength performances of laminated woods, 3-ply parallel- and cross-laminated wood specimens exposed under atmosphere conditions after bending creep test were prepared for this study. The effects of density of species, arrangement of laminae and lamination types on dynamic MOE obtained by flexural vibration were investigated, and regression analyses were conducted in order to estimate static bending strength and bending creep performances. Dynamic MOE of parallel-laminated woods showed 1.0~1.2 times higher values than static bending MOE, and those of cross-laminated woods showed 1.0~1.4 times higher values than static bending MOE. The degree of anisotropy of dynamic MOE perpendicular to the grain of face laminae versus that parallel to the grain of face laminae was markedly decreased by cross-laminating. There were strong correlations between dynamic MOE by flexural vibration and static bending MOE (correlation coefficient r = 0.919~0.972) or bending MOR (correlation coefficient r = 0.811~0.947) of 3-ply laminated woods, and the correlation coefficient were higher in parallel-laminated woods than in cross-laminated woods. It indicated that static bending strength performances were able to be estimated from dynamic MOE by flexural vibration. Also, close correlations between the reciprocal of dynamic MOE by flexural vibration and initial compliance at 0.008 h of 3-ply laminated woods were found (correlation coefficient r = 0.873~0.991). However, the correlation coefficient between the reciprocal of dynamic MOE and creep compliance at 168 h of 3-ply laminated woods was considerably lower than those between dynamic MOE and initial compliance, and it was hard to estimate creep compliance with a high accuracy from dynamic MOE due to the variation of creep deformation.

• Journal of the Korean Wood Science and Technology
• /
• 제40권5호
• /
• pp.303-310
• /
• 2012

Heat treatment improves dimensional stability and sound absorption properties of wood. However, mechanical properties of wood can be deteriorated during the heat treatment. The effect of heat treatment on the bending strength and hardness of wood for Korean paulownia, Pinus densiflora, Lidiodendron tulipifera and Betula costata were measured. The heat treatment temperature has been investigated at $175^{\circ}C$ and $200^{\circ}C$, respectively. The results showed that the weight and density of wood decreased after heat treatment. It was found that the density by heat treatment was lower at $200^{\circ}C$ than that at $175^{\circ}C$. And, MOE increased with the reduced density. On the contrary, MOR and hardness decreased. In all conditions, It was found that there was a high correlation of 1% level between bending modulus of elasticity and modulus of rupture.

• 한국가구학회지
• /
• 제19권5호
• /
• pp.350-357
• /
• 2008

This research investigates the bending properties to predict the work-energy to maximum load and impact bending energy from static bending and impact bending test. Specimens were prepared from lumber made of thinning crop-trees. Matched specimens were used for MC 12% and green moisture specimens to measure the effect of moisture content on the absorbed energy from static and impact bending tests. The bending properties such as MOE, MOR, etc. is a good predictor to investigate the work-energy and work-energy per unit volume from static bending and impact bending test. The impact bending energy is increased with increasing moisture content. However, the work to maximum load from static bending test is increasing with increasing the MC only for higher density species.

• Journal of the Korean Wood Science and Technology
• /
• 제42권6호
• /
• pp.723-731
• /
• 2014

공진주파수 모드를 이용하는 비파괴 평가기술법을 거대억새 파티클 보드를 페놀수지로 함침한 후 탄화온도별(600, 800, 1000, $1200^{\circ}C$)로 제조한 세라믹에 적용하였다. 동적 탄성계수와 정적 휨 탄성계수는 탄화온도가 증가할수록 증가하였다. 휨 강도에 대한 동적 탄성계수 및 정적 휨 탄성계수는 밀접한 상관관계를 나타내었다. 그러나 휨 강도에 대한 상관관계에서 정적 탄성계수 보다 동적 탄성계수가 더 밀접한 상관관계를 나타내었다. 따라서 공진 주파수 모드를 사용하는 동적 탄성계수측정법으로 소성온도에 따라 제조된 거대억대 파티클보드의 휨 강도를 예측하는 비파괴 평가 방법으로 유용할 것으로 판단된다.

• 한국가구학회지
• /
• 제20권4호
• /
• pp.281-289
• /
• 2009

This research examined the technical feasibility of composite that had two layers of fiberglass reinforcement to enhance the load carrying capacity of lumber. Specimens were prepared from standard lumber made of thinning crop trees such as Larix kaempferi, Pinus koraiensis, and P. rigida. Results indicated that bending properties, hardness, and wood screw withdrawal load of low density lumber from the P. koraiensis increased as the number of layers of fiberglass reinforcement increased. Composite produced by VARTM method showed the MOE increased in all specimens, while the MOR differed on the location, whether the 2-layers of FRP is put on tensile zone or compressive zone. The MOR of high density lumber from Larix kaempferi and P. rigida decreased when they placed into tensile zone, but low density lumber from P. koraiensis increased in same location. The bending toughness only increased high density lumber of Larix kaempferi as the number of layers of fiberglass reinforcement increased. The technique developed by this study may increase an opportunity to use small diameter log with low density for commercial purposes.

• Journal of the Korean Wood Science and Technology
• /
• 제32권3호
• /
• pp.59-65
• /
• 2004

This paper reports the mechanical properties of bending, compression and hardness of woodceramics manufactured at different carbonizing temperatures (600℃, 800℃, 1000℃, 1200℃ and 1500℃) in a vacuum sintering furnace using sawdust boards of Pinus densiflora, Pinus koraiensis and Larix kaemferi. The highest values of bending MOR (MOR_b) were 104 kgf/cm² (1200℃), 91 kgf/cm² (1500℃) and 86 kgf/cm² (1500℃), the highest values of compression strength were 152 kgf/cm²(1200℃)), 160 kgf/cm²(1000℃) and 189 kgf/cm²(1000℃), the highest values of hardness were 2.00 kgf/mm²(800℃), 2.01 kgf/mm² (1200℃) and 2.28 kgf/mm² (1000℃) in P. densifora, L. kaemferi and P. koraiensis, respectively. The carbonizing temperature of 600℃ was not proper to the mechanical properties for three kinds of sawdust boards and the highest values of mechanical properties were different from the kinds of mechanical properties and species of sawdust boards. Therefore, it is necessary to manufacture woodceramics at a proper temperature for particular species of sawdust boards to obtain good mechanical properties.

• Journal of the Korean Wood Science and Technology
• /
• 제19권3호
• /
• pp.53-61
• /
• 1991

Mechanical properties of composite panel made with 3mm thick Apitong(Dipterocarpus grandiflorus) veneer on each face of particleboard core of 4 different specific gravity were determined. The results obtained were as follows: 1. Measured MOR and MOE increased with an increased in specific gravity of particleboard core. 2. Test results showed that the difference in bending properties between flatwise bending and edgewise bending was present. The average MOE value of flatwise loading was higer than that of epdgewise loading. But it was shown reverse tendency in MoR and MOE. 3. The delamination between face veneer and core particle was found in flatwise bending but nell in edgewise. 4. These composite panel could be substituted for plywood and other panel materials in furniture making as considered suitable allowable stress and bending strength.

• 한국가구학회지
• /
• 제18권1호
• /
• pp.20-30
• /
• 2007

This experiment was carried out to investigate the effects of number and location of finger joints on the bending strength of glue-laminated lumbers. Urea resin adhesives were used in this experiment and the resin content was 70% for cold pressing. The lamina were edge-jointed and end-jointed. The specimen were composed of one or three layers. The obtained results are summarized as follows; The effects of finger joints on the decrease of bending strength of glue laminated woods were different according to the number and location of finger joints. The decrease of MOR was highest on the middle position of laminated woods. The effects of several arrangements of finger joints on the bending strength of glue laminated woods showed on Figure 7 and 8. The variance of thickness-laminating on the bending strength of glue laminated woods were larger than those of width-laminating.

• Journal of the Korean Wood Science and Technology
• /
• 제28권3호
• /
• pp.1-8
• /
• 2000

본 연구는 미이용 자원인 소경목(小經木) 조생수(早生樹) 등의 저질원료로부터 고성능을 지니는 구조용 보드를 제조하는 기술을 개발하는 것을 목적으로 하여 할렬 스트랜드 (S)/파티클(P) 복합체의 층구조와 S와 P의 혼합비율을 바꾼 단면구성에 따른 기초적 물성을 검토했다. 그 결과 스트랜드층을 포함하고 있는 SP 복합체의 경우, 전체적으로 휨성능(MOR, MOE)이 매우 높았다. 또 S단층 보드는 현저한 이방성을 나타내었지만 층구조가 PB에 가까워질수록 이방성은 감소하여, 7층 구조의 복합체는 이방성이 적었으며 특히 SP7은 직교방향도 휨강도가 높았다. 습윤시 휨강도 성능도 같은 경향을 나타내었다. 박리강도(IB)는 PB가 가장 높았고, 스트랜드층을 가진 복합체는 거의 같은 값을 나타내었다. 두께팽창율(TS) 은 PB가 가장 적은 값을 나타내었으며, 표층이 P층인 구조가 S표층구조보다 적은 경향을 나타내었다. 복합체의 표면특성은 표층 엘리먼트의 영향을 받아, 적고 미세한 엘리먼트인 P표층의 복합체가 크고 두꺼운 S표층 복합체보다 양호하였다. S와 P의 혼합비율의 영향은, SP비(比)를 증가시켜도 강도물성(MOR, MOE, IB)은 향상되지 않으며, 오히려 저하되는 것도 있었다. 두께팽창율(TS)은 SP 비(比) 1:1 이상의 복합체에서는 S만으로 제조한 보드와 같은 정도의 값을 나타내었다.

• 한국가구학회지
• /
• 제11권2호
• /
• pp.7-12
• /
• 2000

This paper describes the bending strength properties of laminated woods which had three kinds of specimens according to finger length-12, 4.5 mm and butt joint and the acoustic emissions (AEs) generated during the test. 3-ply laminated wood beams were tension side layers (lower layers) composed of one middle lamina and two side-jointed laminae, with one butt joint ($_1BJ$), one finger joint (12mm, $_1FJ_{12}$) or one finger joint (4.5mm, $_1FJ_{4.5}$) in the middle lamina of tension side layer. And 3-ply laminated wood beams were tension side layers (lower layers) also composed of one lamina, with one butt joint (BJ), one finger joint (12mm, $FJ_{12}$) or one finger joint (4.5mm, $FJ_{4.5}$/) in tension side layer. Cryptomelia pieces were cut for butt and two finger types and glued with resorcinol-phenol resin adhesive. The results were as follows It was not effective in the bending modulus of elasicity (MOE) with IFJL type and had no difference from finger length. The bending modulus of rupture (MOR) of laminated wood beams including finger joint was the same values as that including butt feint and had no difference from finger length. It was effective in MOE with FJL type and had no difference from finger length. The effect of finger joint on MOR was much higher than that of butt joint but had no difference from finger length. The AE generation time of IFJL type was earlier than that of the control wood and the number of AE count was much more than that of the control wood. However, the AE generation time of FJL type was earlier than that of the control wood and the number of U count was much fewer than that of the control wood.