• 설비공학논문집
• /
• 제14권12호
• /
• pp.1056-1062
• /
• 2002

This paper reports the characteristics of the three dimensional turbulent flow in the 180 degree bends with decreasing cross-sectional area by numerical method. Calculated pressure and velocity, Reynolds stress distributions are compared to the experimental data. Turbulence model employed are low Reynolds number k-epsilon model and algebraic stress model. The results show that the main vortex generated from the inlet part of the bend maintained to outlet of the bend because of the contraction of cross-sectional area. The rate of increase of turbulent kinetic energy through the bend are lower than that of mean flow. Secondary flow strength of the flow is lower about 60% than that of square duct flow.

• 설비공학논문집
• /
• 제16권9호
• /
• pp.804-810
• /
• 2004

This paper reports the characteristics of the three dimensional turbulent flow by numerical method in the 180 degree bends with increasing cross-sectional area. Calculated pressure and velocity, Reynolds stress distributions are compared to the experimental data. Turbulence model employed are low Reynolds number $textsc{k}$-$\varepsilon$ model and algebraic stress model(ASM). The results show that the main vortex generated from the inlet part of the bend maintained to outlet of the bend and vortices are continually developed at the inner wall region. The distribution of turbulent kinetic energy along the bend are increase up to 120$^{\circ}$ because of increment of cross-sectional area. Secondary flow strength of the flow is lower about 60% than that of square duct flow.

• KCI Concrete Journal
• /
• 제11권3호
• /
• pp.211-221
• /
• 1999

A method to determine the fracture energy of concrete is investigated. The fracture energy may be calculated from the area under the complete load-deflection curve which can be obtained from a stable three-point bend test. Several series of concrete beams have been tested. The Present experimental study indicates that the fracture energy decreases as the initial notch-to-beam depth ratio increases Some problems to be observed to employ the three-point bend method are discussed. The appropriate ratio of initial notch-to-beam depth to determine the fracture energy of concrete is found to be 0.5. It is also found that the influence of the self-weight of a beam to the fracture energy is very small A simple and accurate formula to predict the fracture energy of concrete is proposed.

• 한국지진공학회논문집
• /
• 제20권6호
• /
• pp.351-360
• /
• 2016

In regions of low-to-moderate seismicity, various types of lap splices are used for longitudinal reinforcement of columns at the plastic hinge zones. The seismic performance of such lap spliced columns, such as strength, deformation capacity, and energy dissipation, is affected by material strengths, longitudinal re-bar size, confinement of hoops, lap splice location, and lap splice length. In the present study, cyclic loading tests were performed for columns using three types of lap splices (bottom offset bar splice, top offset bar splice, and splice without offset bend). Lap splice length($40d_b$ and $50d_b$) was also considered as test parameters. Ties with 90-degree end hooks were provided in the lap splice length. The test results showed that strength, deformation capacity, and energy dissipation of columns significantly differed depending on the details and the length of lap splices. The bottom offset bar splice showed high ductility and energy dissipation but low strength; on the other hand, the top offset bar splice and the splice without offset bend showed high strength but moderate ductility and energy dissipation.

• 한국분말재료학회지
• /
• 제4권3호
• /
• pp.222-229
• /
• 1997

A P/M high speed steel of ASP 30 grade was austenitized, gas quenched and tempered at various conditional. The mechanical properties such as hardness, bend strength and fracture toughness were evaluated after heat treatment. The microstructure and the type and volume fraction of carbides were analyzed by an optical microscope, image analyzer and XRD. The primary carbides after the heat treatment were MC and $M_6C$ type. The volume of the total carbide varied from 10 to 15% depending on the austenitizing and tempering temperature. The tempering temperature for maximum hardness was at around 52$0^{\circ}C$. But the maximum bend strength was obtained at about 55$0^{\circ}C$. The fracture toughness was largely affected by the presence of retained austenite after gas quenching and secondary hardening during tempering.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 춘계학술발표 개요집
• /
• pp.137-138
• /
• 1995

• 콘크리트학회논문집
• /
• 제20권5호
• /
• pp.635-642
• /
• 2008

건설구조물에서 보통철근의 부식을 방지하기 위하여 에폭시 도장 철근이 널리 사용되고 있다. 그러나 에폭시 도장철근은 성능과 코스트 면에서 불리하며, 특히 취성적이고, 부착성 및 현장 가공성 등의 취약점 때문에 현장에서 사용상의 제약을 받고 있다. 본 연구는 에폭시 도장 철근을 대체할 수 있는 도장재료로서 유기계 폴리머와 시멘트의 무기계를 혼합한 하이브리드 (hybrid)형 폴리머 시멘트 슬러리를 개발하기 위한 것으로서, 특히 인장특성과 접착성에 관한 연구이다. 폴리머 시멘트 슬러리는 4종류의 폴리머 디스퍼션과 혼화재로서 플라이애쉬와 실리카퓸을 혼입하여 제작되었으며, 도장두께, 인장특성, 접착성 및 내굴곡성 시험을 실시하였다. 연구결과, 폴리머 시멘트 슬러리의 점도는 폴리머 디스퍼션의 종류에 따라 크게 영향을 받았으며, 플라이애쉬를 혼입함에 따라 약간 감소하였다. 또한 폴리머-결합재비 100%에서 폴리머 시멘트 슬러리의 적정 도장두께가 확보되었으며, 도장두께는 물-결합재비와 폴리머-결합재비에 의해 다양화 할 수 있었다. 철근의 도장을 위한 적정 도장 두께는 부착강도, 접착성 및 내굴곡성을 고려할 때, 보통 $150{\sim}250{\pm}50{\mu}m$ 범위였다. 본 연구에서 폴리머 시멘트 슬러리의 인장특성 및 접착성, 그리고 도장강의 내굴곡성은 양호하게 평가되어, 향후 에폭시 도장철근을 대체할 수 있는 재료로 사용가능성을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.327-329
• /
• 2006

In this paper, the cutting qualities by laser dicing and fracture strength of a silicon die is investigated. Laser micromachining is the non-contact process using thermal ablation and evaporation mechanisms. By these mechanisms, debris is generated and stick on the surface of wafer, which is the problem to apply laser dicing to semiconductor manufacture process. Unlike mechanical sawing using diamond blade, chipping on the surface and crack on the back side of wafer isn't made by laser dicing. Die strength by laser dicing is measured via the three-point bend test and is compared with the die strength by mechanical sawing. As a results, die strength by laser dicing shows a decrease of 50% in compared with die strength by mechanical sawing.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.877-880
• /
• 2006

The stochastic nature of the tensile strength of concrete is investigated theoretically and experimentally. The tensile strength of concrete was modeled by a theory based on the failure probability of a crack arbitrarily oriented within a concrete body. According to this model, the stochastic nature of the tensile strength depend on the current stress state. This aspect was checked experimentally using a classical three point bend specimen and a rectangular plate specimen loaded at the center. It has been known that the biaxial strength is no different from the uniaxial strength. However, if the region where the tensile strength is constant gets small, the biaxial tensile strength increases and its stochastical variation decreases.

• Computers and Concrete
• /
• 제20권1호
• /
• pp.39-47
• /
• 2017

In this paper, mode I fracture toughness of rock was determined by direct and indirect methods using Particle Flow Code simulation. Direct methods are compaction tension (CT) test and hollow centre cracked quadratic sample (HCCQS). Indirect methods are notched Brazilian disk (NBD) specimen, the semi-circular bend (SCB) specimen, hollow centre cracked disc (HCCD), the single edge-notched round bar in bending (SENRBB) specimen and edge notched disk (END). It was determined that which one of indirect fracture toughness values is close to direct one. For this purpose, initially calibration of PFC was undertaken with respect to data obtained from Brazilian laboratory tests to ensure the conformity of the simulated numerical models response. Furthermore, the simulated models in five introduced indirect tests were cross checked with the results from direct tests. By using numerical testing, the failure process was visually observed. Discrete element simulations demonstrated that the macro fractures in models are caused by microscopic tensile breakages on large numbers of bonded discs. Mode I fracture toughness of rock in direct test was less than other tests results. Fracture toughness resulted from semi-circular bend specimen test was close to direct test results. Therefore semi-circular bend specimen can be a proper test for determination of Mode I fracture toughness of rock in absence of direct test.