• Nuclear Engineering and Technology
• /
• 제49권1호
• /
• pp.254-266
• /
• 2017

Finite-element analysis based on elastic-perfectly plastic material was conducted to examine the influence of structural deformations on collapse loads of circumferential through-wall critically cracked $90^{\circ}$ pipe bends undergoing in-plane closing bending and internal pressure. The critical crack is defined for a through-wall circumferential crack at the extrados with a subtended angle below which there is no weakening effect on collapse moment of elbows subjected to in-plane closing bending. Elliptical and semioval cross sections were postulated at the bend regions and compared. Twice-elastic-slope method was utilized to obtain the collapse loads. Structural deformations, namely, ovality and thinning, were each varied from 0% to 20% in steps of 5% and the normalized internal pressure was varied from 0.2 to 0.6. Results indicate that elliptic cross sections were suitable for pipe ratios 5 and 10, whereas for pipe ratio 20, semioval cross sections gave satisfactory solutions. The effect of ovality on collapse loads is significant, although it cancelled out at a certain value of applied internal pressure. Thinning had a negligible effect on collapse loads of bends with crack geometries considered.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.414-414
• /
• 2007

In this study, Liquid Crystal (LC) alignment and tilt angle generation in Nematic Liquid Crystal (NLC) with negative dielectric anisotropy on the homeotropic PI surface with new ion beam exposure are reported. Also. high density of ion beam energy (DuoPIGatron type Ar ion gun) is used in this study. The tilt angle of NLC on the homeotropic Polyimide (PI) surface for all incident angles is measured about 38 degree and this has a stabilization trend. And the good LC alignment of NLC on the PI surface with ion beam exposure of $45^{\circ}$ incident angle was observed. Also the tilt angle of NLC on the homeotropic PI surface with ion beam exposure of $45^{\circ}$ had a tendency to decrease as ion beam energy density increase. The tilt angle could be controlled from verticality to horizontality. Also, the LC aligning capabilities of NLC on the homeotropic PI surface according to ion beam energy has the goodness in case of more than 1500 eV. Finally. the superior LC alignment thermal stability on the homeotropic PI surface with ion beam exposure can be achieved. For OCB(Optically Compensated Bend) mode driving, we can need pretilt angles control for fast response time. In this study, We success pretilt angles control. Consequently, this result can be applied for OCB mode.

• 한국운동역학회지
• /
• 제21권1호
• /
• pp.39-46
• /
• 2011

The purpose of this study was to examine differences between players who bend the left elbow and those who stretch it during the forward swing from BST to BC in a 2-handed backhand stroke among outstanding high school tennis players, and to assess the detailed 3D rotational kinematic characteristics of the shoulder and the hip. Statistically significant differences were observed between groups in the longitudinal axis rotation angle of the shoulder and the angle between the shoulder and the arm at BST, and in the side to side movement of the shoulder, the up and down movement of the hip, the side tilt angular velocity of the shoulder, the side tilt angular velocity of the hip, and the front tilt angular velocity of the hip at BC. The difference in the longitudinal axis rotation angle of the shoulder between the 2 groups suggests a difference in the flexibility of the joint in the shoulder arm racquet system. The longitudinal axis rotation angular velocity of the shoulder reached its peak at 75 % of the duration of the analyzed segment and then decreased little by little until BC. This time is considered the stage for increasing the angular velocity of the upper arm, the forearm, the hand and then the racquet, which are more distal segments than the shoulder.

• 한국기계가공학회지
• /
• 제12권6호
• /
• pp.77-83
• /
• 2013

Orthodontics is a branch of dentistry that is concerned with the study and treatment of malocclusion, which may result from tooth irregularities, disproportionate jaw relationships, or both. Orthodontic devices consist of brackets, archwire connected to each bracket, and bends and hooks for auxiliary functions. Basically, orthodontics involves the interaction of brackets and archwire. It should be noted that uncontrolled tipping can occur due to unwanted movement of the teeth. The bending of an archwire can control the angle of an archwire and the rotation of a tooth. In this study, we predict the relationship between the bending angle of an archwire and the rotation of a tooth using the Kriging interpolation method. Also, we calculate the angle of an archwire that occurs at the minimum value of tooth rotation.

• 대한토목학회논문집
• /
• 제26권5B호
• /
• pp.469-479
• /
• 2006

본 연구에서는 사행수로에서 주 흐름과 이차류의 특성을 정량적으로 분석하고자 중심각이 $150^{\circ}$이고 사행도 1.52인 S자형 사행수로에서 실험을 수행하였다. 평균수심과 유량을 달리하여 다양한 실험 조건 하에서 수행한 실험을 통해 다중 만곡부를 갖는 사행수로에서 이차류의 공간적 변화양상을 관찰하였다. 실험결과, 주 흐름은 실험조건에 관계없이 직선구간에서 좌우 대칭적인 유속분포를 보였고, 만곡부에서는 내안쪽에 최대유속이 발생하고 외안쪽에 최소유속이 발생하는 현상을 발견 할 수 있었다. 이렇게 주 흐름이 최단노선을 따라 발생하는 현상은 기존 연구자들의 결과와 일치하는 것이다. 이차류의 거동은 첫번째 만곡부보다 두 번째 만곡부에서 더욱 활발하게 발달하고 외안 회전류가 뚜렷히 나타남을 발견하였다. 이차류의 강도는 직선구간에서는 낮게 나타나고 만곡부에서는 증가하는 주기적인 현상을 보였으며, 만곡부의 이차류 강도가 직선구간보다 2~3배 크게 나타났다. 또한, 두 번째 만곡부에서 이차류 강도의 최대값이 발생했다. 주 흐름방향의 난류 강도와 Reynolds 전단응력을 분석한 결과, 주 흐름 난류 강도는 주 흐름의 유속편차가 클수록 증가하는 것으로 나타났고 Reynolds 전단응력은 주 흐름방향 유속의 편차가 크게 벌어지는 동시에 이차류가 활발히 생성되는 지점에서 크게 나타나는 경향을 보였다.

• 대한인간공학회지
• /
• 제27권2호
• /
• pp.49-57
• /
• 2008

This study aims to investigate the effect of handle angles of pliers on performance, wrist motion and subjective rating of satisfaction. An experiment was conducted, in which handle angle of pliers was used as independent variable and 14 subjects participated. Based on the literature survey, plier handles angled at 0$^{\circ}$, 10$^{\circ}$, 20$^{\circ}$, 30$^{\circ}$ and 40$^{\circ}$ were adopted in the experiment. The subjects were instructed to bend iron plates by 90$^{\circ}$ and to cut wires as soon as possible. The results revealed that 1) handle angles of pliers have significant effect on wrist motion and satisfaction(p<0.0001); 2) handle angles of pliers did not affect performance of completing tasks irrespective of types of tasks done in the study; 3) in the initial stage of windup, plier with handle angled at 20$^{\circ}$ produced the least wrist motion of deviation in task of bending iron plates, while plier with handle angled at 40$^{\circ}$ did in task of cutting wires; 4) degree of satisfaction was maximized when handle of pliers was bent by 20$^{\circ}$ in both tasks. On the basis of the results, it is recommended that handle of pliers be bent by 20-30$^{\circ}$ for reducing musculoskeletal disorders related to pliers.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2000년도 춘계학술대회 논문집(Proceeding of the KOSME 2000 Spring Annual Meeting)
• /
• pp.127-133
• /
• 2000

In the present study flow characteristics of turbulent pulsating flow in a square-sectional 180。 curved duct are investigated experimentally. in order to measure axial velocity and secondary flow distributions experimental studies for air flow are conducted in a square-sectional $180^{\circ}$ curved duct by using the LDV system with the data acquisition and the processing system of the Rotating Machinery Resolver (RMR) and the PHASE software. The experiment is conducted on seven sections form the inlet(${\phi}=180^{\circ}$) at $30^{\circ}$ intervals of the duct. The results obtained from the experimentation are summarized as follows : In the axial velocity distributions of turbulent pulsating flow when the ratio of velocity amplitude(A1) is less than one there is hardly any velocity change in the section except near the wall and any change in axial velocity distribution along the phase. The secondary flow of turbulent pulsating flow has a positive value at the vend angle of $150^{\circ}$ without regard to the ratio of velocity amplitude. The dimensionless value of secondary flow becomes gradually weak and approaches zero in the region of bend angle $180^{\circ}$ without regard to the ratio of velocity amplitude.

• 한국CDE학회논문집
• /
• 제10권1호
• /
• pp.40-48
• /
• 2005

A hydraulic hose is an important part of the hydraulic system which transmits power using pressurized fluids. It allows relative motion between components at each end of the hose assembly, and it is much easier to route a hose assembly than it is to bend and install a rigid tubing assembly. Unnecessary loads, which drop the hose's pressure capability and shorten service life, depend on a hose-routing. Therefore, the Hydraulic system designers must be aware to consider unnecessary load does not affect the here. For this consideration in an early stage of the design process, CAD system must support the hose assembly routing design function which is to generate routing path and design fitting angle properly. This paper proposes 2 methods. One is to generate curves that are similar to routing paths of the real hose assembly using the energy minimization method and the optimization method. The other is to design fitting angles that are important design elements of a hose assembly using the Parallel Transport Frame. To implement the proposed methods above, commercial CAD software, CATIA has been integrated with our program.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.424-425
• /
• 2007

We have studied the optically compensated splay mode using reactive mesogen (RM) monomer to reduce setting voltage and phase transition time from initial bend to splay state. When the OCS cell has low pretilt angle close to $45^{\circ}C$, OCS state can be formed easily. The low pretilt angle was formed through the polymerization of UV curable reactive RM monomer at the surfaces. In this way, reorientation of the LC is well defined and thus the device shows better performances in setting voltage and phase transition time.

• 국제물리치료학회지
• /
• 제7권2호
• /
• pp.1041-1045
• /
• 2016

The aim of this study was to investigate the effect of Maitland mobilization and Kaltenborn-Evjenth mobilization on the SLR angle. Subjects randomly divided into Kaltenborn-Evjenth group(n=8) and Maitland group(n=7). The mean height, age, body weight was $176.00{\pm}5.10cm$, $22.75{\pm}1.83years$, $72.63{\pm}10.65kg$ respectively in Kaltenborn-Evjenth group. The mean height, age, body weight was $175.00{\pm}5.60cm$, $22.29{\pm}3.68years$, $78.00{\pm}12.36kg$ respectively in Maitland group. Hip joint accessary movements with Grade III or IV were applied depend on the patient's condition to the restricted direction for 1 minute each set, and performed 5 set in a Maitland group. Hip joint anteroposterior gliding with Grade III were applied 60 for 1 minutes each set, and performed 5 set in a Kaltenborn-Evjenth group. The angle of first pain was referred to as P1 and subjects were pointed out that they could not bend the knee anymore, then examiner measure SLR angle. The SLR was significantly increased in the Maitland group compared to the Kaltenborn-Evjenth group after intervention(p<.05). In a within group difference, SLR significantly increased in the both groups(p<.05). These results indicated that Maitland mobilization could be recommended the excellent technique to increase the hip flexion in patient with hip hypo-mobility.