• 한국수자원학회논문집
• /
• 제49권6호
• /
• pp.529-536
• /
• 2016

본 연구는 급경사 자갈하상 만곡수로의 이동상 수리실험을 이용하여 만곡부 최대세굴심 산정공식들의 적용성을 평가하였다. 평균입경 43mm의 하천자갈을 $90^{\circ}$ 만곡 급경사 개수로에 포설하고 유량과 하상경사에 따른 만곡부의 최대세굴심을 조사하고 세굴심 공식으로 산정한 최대세굴심과 비교하였다. 자갈하상 만곡부 국부세굴은 유입부의 하상경사 0.02이상 $F_r$ 0.95이상에서 발생하였다. 이 수로에서 Lacey공식과 Zeller공식을 제외한 기존 세굴심 산정공식들은 최대세굴심을 과대 추정하는 것으로 나타났다. 하상재료를 고려한 Lacey공식과 접근경사와 만곡도를 반영한 Zeller공식은 급경사 자갈하상 만곡부의 최대세굴심 평가에 적용될 수 있는 것으로 판단된다.

• 한국추진공학회지
• /
• 제9권1호
• /
• pp.53-60
• /
• 2005

소형위성 발사체 추진제 공급계 배관의 구부러짐으로 인하여 배관내부의 추진제 유동은 불균일하며 이는 터보펌프 전단의 블레이드의 파괴 및 후단의 가압된 추진제의 불안정성을 야기시킨다. 따라서 추진제의 효율적인 공급을 위하여 vane이 장착된 곡관 배관이 필요하며 내부에서의 유동장을 수치해석으로 규명하여 그 문제점을 해결할 수 있는 지 연구하였다. 따라서, 본 연구에서는 각각 90도와 45도로 구부러진 3인치 산화제 배관과 2.5인치 연료 배관의 구부러진 부분에는 $0\sim3$개의 vane을 등 간격으로 설치하였다. 3차원 Navier-Stokes 방정식을 풀기 위하여 상용코드를 이용하였으며, 곡관 배관 설계를 평가하기 위하여 각 90, 45도의 vane이 설치되지 않은 곡관과 $1\sim3$개의 vane이 장착된 곡관을 비교하였다. vane의 개수에 의한 배관 설계의 영향을 알아보기 위하여 90, 45도의 곡관에 vane이 0, 1, 2, 3개가 등 간격으로 장착이 되었을 때의 결과를 비교하였다. 배관내의 유동 균일성과 차압을 알기 위하여 속도크기와 압력분포를 계산하였다. vane이 많을수록 곡관의 각도가 클수록 곡관을 지난 유동은 더 균일해졌으나 배관 차압은 더 증가하였다.

• 대한토목학회논문집
• /
• 제39권2호
• /
• pp.297-306
• /
• 2019

개수로 만곡부에서 흐름은 원심력이 작용하기 때문에 횡방향 수면경사가 나타나고 유심선은 만곡 외측으로 치우친다. 수중 수제는 만곡부의 다양한 공학적인 문제를 해결하는 데 사용될 수 있다. 수중 수제가 흐름방향과 이루는 입사각과 수제 열 간격이 만곡부의 하상변동과 편수위에 미치는 영향을 파악하기 위해서 $90^{\circ}$만곡 직사각형 단면 수로에 잔자갈을 깔고 이동상 수리실험을 하였다. 만곡부에 수중 수제를 설치하면 최대 세굴심은 증가하나 균일한 둔각으로 수제를 설치하면 세굴을 줄일 수 있다. 수제를 설치한 만곡부에 수제설치 기준하상의 형성유량과 같은 유량이 흐를 경우 최대 세굴이 발생하는 위치가 하류로 이동하고 편수위는 증가한다. 그 유량보다 작으면 최대 세굴심의 위치가 상류로 이동하며 편수위는 감소한다. 만곡부에서 수중 수제는 입사각, 유량, 수제 열 간격의 상호작용에 따라 하상변동과 편수위에 대한 영향이 다르다.

• 한국전자파학회지:전자파기술
• /
• 제6권3호
• /
• pp.80-90
• /
• 1995

마이크로스트립 단일선로, 직각벤드 및 결합선로의 산란행렬을 multipart r$\xi$twork model을 이용하여 1-18GHz 범위에서 계산했다. 단일선로는 평면형 도파관 모텔을 이용하여 해석했다. 직각벤드의 경우는 두개 의 사각형 부분으로 나누어져 각 부분은 단일선로와 같은 방법으로 해석되며, 각 부분의 임피던스 행렬은segmentation 방볍을 이용하여 연결된다. 결합선로 사이의 전자계 결합의 해석에는 Green 함수를 이용하는 기 존의 방법보다 계산시간이 적게 소요되는 새로운 방법이 이용되었다 상기의 세가지 구조에 대한 수치해석 결 과는 SuperCompact의 결과와 잘 일치하며, 이는 상기의 방법이 복잡한 단일 및 결합선로 불연속구조의 해석에 유용하게 사용될 수 있음을 보여준다

• 대한의용생체공학회:의공학회지
• /
• 제31권6호
• /
• pp.472-480
• /
• 2010

Mechanically deformed cartilage undergoes a temperature dependent phase transformation resulting in reshaping of cartilage. Laser-assisted cartilage reshaping (LCR) is recently introduced to recreate the underlying cartilage framework in structures such as ear, larynx, trachea, and nose. However, this procedure has not been fully supported by confirmed efficacy because of the lack of scientific research and its safety issues. The purpose of this study is to evaluate current laser sources to determine optimal laser wavelength for LCR using mathematical simulations and investigate optical, thermo-mechanical, and backscattering properties of cartilage after laser irradiation. The results showed that 1444 nm wavelength was effective for reshaping of cartilage with minimal thermal damage in the surrounded tissues by monte carlo simulations. Analysis of bend angle changes, thermo-mechanical characteristics, and backscattered properties may be useful to better identify the biophysical transformation responsible for stress relaxation in cartilage and develop an optical feedback control methodologies.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 제5회 박판성형 SYMPOSIUM
• /
• pp.45-48
• /
• 2006

Recently, the use of tubular hydroforming technology has seen increased usage and increased consideration for wide range of tubular automotive applications. In manufacturing hydroformed parts, bending and pre-forming operations are often required prior to the hydroforming process. Higher bending quality of bent tubes is crucial for the successful hydroforming operation because most of plastic strains and wall thinning at the extrados of bend area occur in the bending operation. Springback is also observed due to elastic recovery of tube material after bending. Proper correction of springback is required not only to well place the bent tube into a hydroforming die cavity but also to avoid pinching when the upper die is brought down to closing position. Therefore, prediction of springback at early development stage is one of the key factors to produce high quality hydroformed parts. In this study, a variety of bending experiments has been carried out to investigate springback amount under change in bending angle and material boosting. Throughout the experimental approach, springback characteristics of bent tubes are quantified according to the change in various bending parameters, and a mathematical model to predict correction amount of springback to a given bend angle is found.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.15-23
• /
• 2000

In the present study, flow characteristics of turbulent pulsating flow in the square-sectional $180^{\circ}$curved duct are investigated experimentally. In order to measure axial direction velocity and secondary flow distributions, experimental studies for air flow are conducted in the square-sectional $180^{\circ}$curved duct by using the LDV system with the data acquisition and the processing system of the Rotating Machinery Resolver (RMR) and the PHASE software. The experiment is conducted on seven sections form the inlet($\phi=0^{\circ}$) to the outlet($\phi=180^{\circ}$) at $30^{\circ}$intervals of the duct. The results obtained from the experimentation are summarized as follows : In the axial direction velocity distributions of turbulent pulsating flow, when the ratio of velocity amplitude (A1) is less than one, there is hardly any velocity change in the section except near the wall and in axial velocity distribution along the phase. The secondary flow of turbulent pulsating flow has a positive value at the bend angle of $150^{\circ}$regardless of the ratio of velocity amplitude. The dimensionless value of secondary flow becomes gradually weak and approaches zero in the region of bend angle $180^{\circ}$without regard to the ratio of velocity amplitude.

• 소성∙가공
• /
• 제29권5호
• /
• pp.282-289
• /
• 2020

Flexible roll forming is an advanced sheet-metal-forming process that allows the production of parts with various cross-sections. During the flexible process, material is subjected to three-dimensional deformation such as transverse bending, inhomogeneous elongations, or contraction. Because of the effects of process variables on the quality of the roll-formed products, the approaches used to investigate the roll-forming process have been largely dependent on experience and trial- and-error methods. Web-warping is one of the major shape defects encountered in flexible roll forming. In this study, an SVR model was developed to predict the web-warping during the flexible roll forming process. In the development of the SVR model, three process parameters, namely the forming-roll speed condition, leveling-roll height, and bend angle were considered as the model inputs, and the web-warping height was used as the response variable for three blank shapes; rectangular, concave, and convex shape. MATLAB software was used to train the SVR model and optimize three hyperparameters (λ, ε, and γ). To evaluate the SVR model performance, the statistical analysis was carried out based on the three indicators: the root-mean-square error, mean absolute error, and relative root-mean-square error.

• 대한기계학회논문집A
• /
• 제21권11호
• /
• pp.1885-1895
• /
• 1997

As track density needs to increase to the order of 10, 000 tpi, the suspension has become a critical component in hard disk drives. One of the main obstacles to attain high track density is the structural resonances of the suspension in lateral direction. We investigate the suspension dynamics through the experimental modal analysis and the finite element method. An LDV (Laser Doppler Vibrometer) is employed to measure the response of the suspension which is excited by a shaker and an inpulse hammer for the free condition and the loaded condition, respectively. After comparing the experimental and numerical results, we study how the initial geometry of the bend region affects the suspension dynamics. It is found that the natural frequency of the sway mode decreases as the bend ratio and the bend angle increase. The shape of torsional mode changes as the mass of a slider increases, resulting in a local decrease in the natural frequency.

• Nuclear Engineering and Technology
• /
• 제40권1호
• /
• pp.37-48
• /
• 2008

Flow fields inside feeder pipes have been simulated numerically using a CFD (computational fluid dynamics) code to calculate the shear stress distribution, which is the most important factor in predicting the local regions of feeder pipes highly susceptible to FAC (flow-accelerated corrosion)-induced wall thinning. The CFD approach, with schemes used in this study, to simulate the flow situations inside the CANDU feeder pipes has been verified as it showed a good agreement between the investigation results for the failed feedwater pipe at Surry unit 2 plant in the U.S. and the CFD calculation. Sensitivity studies of the three geometrical parameters, such as angle of the first and second bends, length of the first span between the grayloc hub and the first bend, and length of the second span between the first and the second bends have been performed. CFD analysis reveals that the local regions of feeder pipes of Wolsung unit 1 in Korea, on which wall thickness measurements have been performed so far, are not coincident with the worst regions predicted by the present CFD analysis located in the connection region of straight and bend pipe near the inlet part of the bend intrados. Finally, based on the results of the present CFD analysis, a guide to the selection of the weakest local positions where the measurement of wall thickness should be performed with higher priority has been provided.