• Korean Journal of Optics and Photonics
• /
• v.15 no.5
• /
• pp.415-422
• /
• 2004

We propose and present a new multiplexed bend loss type single-mode fiber-optic sensor system for displacement measurement in order to measure the displacement of several mm of civil engineering structures such as bridges and buildings. We make a bend loss type fiber-optic sensor for measuring displacements using the signal difference between two reflection signals due to various bend losses generating at a pair of optical connectors by using the optical time domain reflectometer. And we fabricate a multiplexed bend loss type fiber-optic sensor detecting linear displacements of 4 measuring positions of an object by setting these new 4 fiber-optic sensors on a single mode fiber simultaneously. We find that the multiplexed fiber-optics displacement sensor has linearity of 0.9942, maximum displacement of 6 mm, and accuracy of 6% for 4 measuring points.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.1
• /
• pp.53-60
• /
• 2005

The use of pipe-bends brings about non-uniform flows at the exit of them due to the velocity difference between inner and outer flows inside the bend. These phenomena may cause turbopump of satellite launch vehicle to run off-design and reduce its efficiency, and also introduce unstable influx of propellants to engine manifold after passing through a turbopump. In order to improve the uniformity of flow at the bend exit, certain turning vanes are set up in the bend pipe normally. Correspondingly the design is an $90^{\circ}\;and\;45^{\circ}$ bend pipes that incorporate with the maximum three turning vanes. All designs were analyzed with numerical analysis by solving the Navier-Stokes equations in three dimensions in case of each respective fuel and oxidizer. Evaluations of the vaned pipe bends designs were accomplished by the velocity magnitude distributions and the predicted pressure drops. We could find that the more vaned bend pipe and larger angle pipe under consideration effectively, the more uniform velocity magnitude of the bend and pressure losses.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.23 no.4
• /
• pp.149-166
• /
• 2021

This study tried to suggest a drafting method to draft tight fit torso patterns suitable for adult males with a sway back somatotype and a bend forward somatotype by setting and distributing the ease through the completion of the somatic surface pattern using the 3D body surface segment method. It was intended to be presented as a drafting method. As for the research method, the suitability of the somatic surface patterns and the tight fit torso patterns were confirmed by the evaluation of virtual wear, and the patterns were modified and supplemented. The research results are as follows. In the first evaluation of the tight fit torso patterns, the average, for 55 evaluation items, was 3.92 points for the sway back somatotype and 3.89 points for the bend forward somatotype. In the second evaluation, the bend forward somatotype was 4.51 points and the sway back somatotype was 4.62 points. The chest circumference ease amount for the bend forward somatotype and the sway back somatotype are 6.5% (6.8 cm) and 7% (6.8 cm) of the chest circumference, respectively, and the distribution of the front and back ease is the same at 4:6 (2.72 cm:4.08 cm). The waist circumference ease amount is 6.5% (5.8cm) and 6.5% (5.6 cm) of the waist circumference dimensions, and the distribution of the front and backease are 5:5 (1.45 cm: 1.45 cm) and 4:6 (2.24 cm: 3.36 cm), respectively. The completed tight fit torso patterns were converted into institutional formulas and presented as a drafting method.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.496-500
• /
• 2009

Optically compensated bend liquid crystal display (OCB-LCD) has many application fields owing to its fast response time and wide viewing angle. However, in order to operate the OCB-LCD in bend state, this device needs quick transitions from the initial splay state to bend state. Unlike conventional approach using transient high voltage for the transition, the OCB-LCD with high surface tilt angle, which was achieved by polymerization of UV curable reactive mesogen monomer under certain voltage, was manufactured and the cell showed bend state initially. Electro-optic and electrical characteristics of the cell were analyzed. The cell shows a fast response time owing to high surface pretilt angle and very low residual DC less than 0.1 V although another polymer layer is formed above polymer alignment layers.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.1061-1062
• /
• 2012

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.194-195
• /
• 2002

We report a fast-switching polymer-stabilized bend nematic (PSBN) device. The morphology study reveal a templated polymer networks captures the orientation of the field deformed nematic host.

• Journal of the Korean Chemical Society
• /
• v.19 no.4
• /
• pp.269-279
• /
• 1975

Photosensitive properties of naphthoquinone-1,2-diazide-5-sulfonyl esters (PGND, BEND and PVAND) of polyglyceryl phthalate(PG), bisphenol A-epichlorohydrin condensate(BE) and polyvinyl alcohol(PVA) were investigated by the change of solubility before and after exposing to light. Various samples coated on glass or quartz plates were exposed to light under various conditions and steeped in aqueous alkali solution, and then the yield of residual film(W/W0) was determined. The yield of residual film, which was closely related to the sensitivity of the film, was affected by the degree of polymerization of the backbone resin, sensitizers and their concentration. In polymer homologs, the sensitivity was dependent on the degree of polymerization(the higher, the better). And also, it was most effective when 5 % of sensitizers to esters was used. The minimum exposed time was 0.6 min. for PGND-1, 1.0 min. for BEND-1, and 3.0 min. for PVAND-1. Most effective sensitizers for PGND, BEND and PVAND among those used here were benzanthrone, 5-nitroacenaphthene and picramide, respectively. The spectral sensitivities of PGND, BEND and PVAND were examined by comparing their spectrograms with UV-spectra in a solid state. Also, the sensitization and spectral sensitivity of the above polymers were studied. All the polymers containing the sensitizers showed optical sensitization. From the fact that in either case of sensitized or unsensitized sample, the ranges of absorption-maximum wave length were almost consistent with sensitivity maximum wave length, it was proved that the light absorbed by a sample served efficiently for photochemical reactions. Benzanthrone was found to be an excellent sensitizer for PGND.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.4
• /
• pp.1-10
• /
• 1990

RILEM proposed three point bend test to determine the fracture energy of concrete, but there is discrepancy between the theoritical and the experimental fracture energy of concrete by the influence of self-weight of concrete. This paper presents four point bend test using proving ring in order to take into account the influence of self-weight of concrete. The initial notch to beam depth ratio was varied from 0.2 to 0.6 in order to investigate the variation of fracture energy of concrete according to the variation of initial notch depth. The proposed four point bend test using proving ring was verified to be superior to three point bend test.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.3
• /
• pp.43-51
• /
• 2020

In this paper, the design of 64 array antennas applied to RWP (Radar Wind Profiler) was described. The design point of the antenna is to ensure isolation between each element and to match the vertical / horizontal radiation pattern. To this end, a single element of the array antenna was proposed as a Bend dipole type, and through simulation, When sequentially sending 5 beams including vertical, the east/west/south/north direction was ±20°, and it was confirmed that no Grating Lobe occurred when steering the beam. The 64 array antenna proposed in this paper was designed with performance equal to or higher than that of overseas products, and was confirmed to be applicable to RWP.

• Journal of the Korean Ceramic Society
• /
• v.31 no.2
• /
• pp.177-184
• /
• 1994

AlN-BN ceramics with BN contents in the range of 10 to 40 wt% were prepared by hot pressing using no additive, or 3 wt%, Y2O3 or CaO, which are common densification aids for AlN. And their machinability, bend strength, and microstructures were investigated. Both the main and radial cutting forces decreased with increasing BN content in all three kinds of samples. For the BN contents of 30 wt% or above, the cutting forces were lower than that of a mild steel tested at a same condition. Especially in the case of main forces, the values were less than a quarter of that of a mild steel, indicating excellent machinability. Bend strength (when the tensile surfaces of specimens were perpendicular to the hot pressing direction) also decreased with BN content mainly due to the much lower Young's modulus of BN compared to AlN. With the composition of 30 wt% BN at which the AlN-BN ceramics started to show better machinability than a mild steel, the bend strength was 150 to 160 MPa, which is greater than that of machinable glass-ceramics of a mica system. With tensile surfaces parallel to the hot pressing direction, however, the bend strength obtained for the samples processed with the sintering acids showed low values (about 40 MPa), since most BN particles had such orientation that their cleavage planes (i.e., basal planes) were perpendicular to the pressing direction.