• 한국강구조학회 논문집
• /
• 제14권1호
• /
• pp.113-120
• /
• 2002

프리캐스트 바닥판 합성형 교량의 전단연결부는 전단포켓과 베딩층이 존재하여 현장타설 강합성 교량과는 다른 구조적 특징을 갖고 있다. 따라서 프리캐스트 바닥판의 전단연결재 설계의 기초를 수립하기 위해서는 실험을 통한 연구가 수행되어야 한다. 프리캐스트 바닥판 합성형 교량의 전단연결재의 피로수명을 평가하기 위하여 베딩층의 두께를 변수로 한 전단연결재의 push-out 피로 시험을 수행하였다. push-out 피로 시험의 수행 결과, 전단연결재의 파괴모드를 확인하였고, 이를 통해 프리캐스트 바닥판 합성형 교량의 전단연결재의 피로수명 곡선식을 유도하였다.

• 한국의류학회지
• /
• 제17권3호
• /
• pp.470-474
• /
• 1993

This study carried out to get some fundamental data for designing lightweight bedding. In This study, the wool blanket, polyester/cotton blended blanket and down quilt were manufactured with a varied materials, structural factors such as yam count, fabric density respectivelyarn. And also, the thermal insulation value of the bedding were measured by warmth retaining tester. In addition, this paper examines the influence of varying materials, structural factors and blanket layers on the thermal insulation effect of the bedding. The main results obtained from this study are as follow : 1. The design of lightweight blankets make an attempting with a varying materials and structural factors such as yam count, fabric densityarn. 2. Almost, the design of lightweight blankets for polyester/cotton blended blanket and down quilt make an attempting without reduction in thermal insulation values. 3. The 6 layers of blanket have less thermal insulation value than the 6 times of blanket for under a layer have. About 27~32% decrease is observed in thermal insulation value of blanket for under 6 layer. 4. The thermal insulation value and areal weight of blankets have a positive relation between the thermal insulation value(Y) and areal weight(X) is based on the following equation. wool blanket : Y = 1.0850X + 0.4188 (r = 0.9992) PIC blended blanket : Y = 0.8845X + 0.3034 (r = 0.9999)

• 한국지반공학회지:지반
• /
• 제12권1호
• /
• pp.47-62
• /
• 1996

The bedding zone which influence directly to the safety of dam is supporting the face slab under hydraulic load in concrete faced rockfill dam. In case that leakage is developed due to various ruptured joint or cracks of face slab and etc., the bedding zone should limit the leakage by low permeability and keep the internal stability. In this study for the proper coefficient of permeability various properties, such as gradation, dry density, performance of embankment work and etc. were analysed. The results from the large scale test of permeability and density are summerized as follows : 1. Coefficient of permeability is decreased clearly by increase of dry density. 2. The particles smaller than the No.4 strive( p,) greatly influences the permeability under dry density of 2.24t 1 m3. 3. In case of C.40 and p,40%, even if dry density decreased to 2.0t/m3, the permeability coefficient is assumed to u x1-scm/s and internal stability is abtained. 4. Generally in dam construction since dry density and uniformity coefficient of bedding zone were higher than 2.2t/m3 and 50 respectively p, of 30~40% is assumed to be suitable and permeability coefficient of below 1$\times$10-3cm l s is expectable.

• 지구물리와물리탐사
• /
• 제7권1호
• /
• pp.25-32
• /
• 2004

We have carried out laboratory measurements of P-wave velocity and deformation strain during $CO_2$ injection into a porous sandstone sample, in dry and water-saturated conditions. The rock sample was cylindrical, with the axis normal to the bedding plane, and fluid injection was performed from one end. Using a piezoelectric transducer array system, we mapped fluid movement during injection of distilled water into dry sandstone, and of gaseous, liquid, and supercritical $CO_2$ into a water-saturated sample. The velocity changes caused by water injection ranged from $5.61\;to\;7.52\%$. The velocity changes caused by $CO_2$ injection are typically about $-6\%$, and about $-10\%$ for injection of supercritical $CO_2$, Such changes in velocity show that the seismic method may be useful in mapping $CO_2$ movement in the subsurface. Strain normal to the bedding plane was greater than strain parallel to the bedding plane during $CO_2$ injection; injection of supercritical $CO_2$ showed a particularly strong effect. Strain changes suggest the possibility of monitoring rock mass deformation by using borehole tiltmeters at geological sequestration sites. We also found differences associated with $CO_2$ phases in velocity and strain changes during injection.

• Structural Engineering and Mechanics
• /
• 제68권5호
• /
• pp.537-547
• /
• 2018

This research presents the effect of anisotropy of the hollow disc mode under Brazilian test using PFC3D. The Brazilian tensile strength test was performed on the hollow disc specimens containing the bedding layers and then these specimens were numerically modeled by using the two dimensional discrete element code (PFC3D) to calibrate this computer code for the simulation of the cracks propagation and cracks coalescence in the anisotropic bedded rocks. The thickness of each layer within the specimens varied as 5 mm, 10 mm and 20 mm and the layers angles were changed as $0^{\circ}$, $25^{\circ}$, $50^{\circ}$, $75^{\circ}$ and $90^{\circ}$. The diameter of internal hole was taken as 15 mm and the loading rate during the testing process kept as 0.016 mm/s. It has been shown that for layers angles below $25^{\circ}$ the tensile cracks produce in between the layers and extend toward the model boundary till interact and break the specimen. The failure process of the specimen may enhance as the layer angle increases so that the Brazilian tensile strength reaches to its minimum value when the bedding layers is between $50^{\circ}$ and $75^{\circ}$ but its value reaches to maximum at a layer angle of $90^{\circ}$. The number of tensile cracks decreases as the layers thickness increases and with increasing the layers angle, less layer mobilize in the failure process.

• 한국의류산업학회지
• /
• 제20권5호
• /
• pp.592-599
• /
• 2018

The purpose of this study is to investigate consumer needs, image sensibility and preference of bedding fabric according to size and spacing of dot pattern. 18 kinds of dot pattern fabrics were designed with different diameters(6, 8, 10cm) and distances(4, 7, 10cm) in regular arrangement of diamond figure. The subjects were 162 male and female university students. The data were analyzed by SPSS 24.0. Fabrics were assessed subjectively using a 5-point scale 17 consumer needs and 33 sensory descriptors. The most consumer's needs for bedding fabric was shown to be functionality of bedding including hygiene, touch, warmth, ease of washing and management, air permeability, and hygroscopicity. The other parameters of consumer's needs were shown to be physical property and design parameter. The results of analysis of the dimension of image sensibility for fabrics with different size and spacing of dots are derived from six factors including joyfulness, coziness, uniqueness, charm, femininity, and complexity. As a result of analysis of preference with fabric kinds, there was a significant difference in preference with fabrics. The preferred fabrics were characterized by the pattern and the base fabric being striking three-dimensionally with 1/3 twill and 3/1 twill fabric. Sensory descriptors related to joyful image and unique image were analyzed as evaluation terms that can distinguish the preferences of fabrics. Correlation analysis showed the fabrics are preferred as the difference in luminance and reflectance between the base and pattern of the fabric become larger and the spacing of patterns become closer.

• 한국염색가공학회지
• /
• 제29권4호
• /
• pp.231-238
• /
• 2017

There are many kinds of elements and processes for the development of high quality bedding products like fiber, high-temperature heat treatment, dyeing process, tenter drying with softening agent and multiple final finishing. Especially we examined the mechanical characteristic properties of fabrics according to different yarn types. The critical physical properties of the yarn consisting the pile knitted fabrics were obtained for the development of the hi-grade bedding items. The material property and the exhaustion behaviour of the developed pile knitted fabrics composing of different yarns were measured and observed. The physical properties of the developed fabric were evaluated through the material property analysis of the yarn, the physical nature of the pile knitted fabrics and the data of the exhaustion performance; tensile strength, tensile elongation, tearing strength, cross section of yarn types, dyeing properties etc. And then high-class of bedding items were knitted using the double raschel machine to make the pile knitted fabrics.

• 터널과지하공간
• /
• 제23권3호
• /
• pp.228-240
• /
• 2013

퇴적암에서 나타나는 이방성은 층리에 의한 영향이 크며, 암석의 수리적 특성에도 영향을 주게 된다. 본 연구에서는 층리가 발달한 다공질 사암을 대상으로, 층리구조에 의해 발생한 공극구조 이방성이 사암의 수리 이방성에 미치는 영향을 분석하였다. 사암의 공극구조 이방성 파악을 위해 X-ray CT(computed tomography)를 이용하여 내부 공극률의 변화양상을 분석하였다. 층리방향에 따른 수리이방성은 층리면과 수평면이 이루는 각도를 $0^{\circ}$에서 $90^{\circ}$까지 $15^{\circ}$간격으로 코어링한 샘플을 제작하여 투수실험을 통해 파악하였다. 투수실험 결과 층리면과 투수방향이 수직인 경우 투수율이 가장 작은 값을 나타낸 반면, 층리면과 투수방향이 평행일 때 가장 높은 투수율을 나타내었으며, 평균 수리이등방비($k_{90^{\circ}}/k_{0^{\circ}}$)가 1.8로 층리에 따른 수리 이방성이 확연하게 나타났다. 또한, 이러한 사암의 수리이방특성은 층리에 의해 공극특성이 서로 다른 층상구조가 형성되기 때문임을 확인하였다.

• 한국축산시설환경학회지
• /
• 제6권3호
• /
• pp.133-140
• /
• 2000

This study was carried out to determine a suitable mixing rate to utilize the PDF as a bedding materials at the pigpens and investigate the effect of substitute processed dustproof fly-ash(PDF) on the odor. In proportion to the increase of substitute rate of the PDF, the utilizable period was extended, and there was a little change of the moisture in the bedding materials. At all the treatment of PDF, there was the significant effect on the maggots and parasites but it didn\`t hinder in the biodegradation. According to highly mixing rate, PDF decreased in the noxious gas ($NH_3$ and $H_2$S) emission. In conclusion, the mixing rate of 30% or above this substituted level will increase replacement terms, and reduce the sawdust cost and the pollutions of breed pigs.

• 터널과지하공간
• /
• 제27권1호
• /
• pp.26-38
• /
• 2017

본 연구는 유 가스 저류층의 암석 투과도 분석을 위해 다양한 층리를 가진 암석과 치밀사암(tight sandstone)을 이용하여 실제 현장의 응력조건을 고려한 암석 투과도를 연구하였다. 다양한 층리를 고려하기 위하여 수평/수직 층리(horizontal & vertical bedding) 및 층리가 존재하지 않는(non-bedding) 암석 시료를 사용하였으며, 균열이 존재하는 저류층의 암석 투과도를 연구하고자 인공균열을 생성시킨 치밀사암을 사용하였다. 실제 심도에서 암석이 받는 유효응력(effective stress)을 암석 투과도 실험에 구현하기 위해 삼축 압력셀을 이용하여 심도별 암석투과도 실험을 수행하였다. 암석 시료에 가해지는 유효응력 및 공극압으로 구분하여 응력조건을 고려하였다. 실험은 두 가지 형태의 응력 해방조건을 고려하여 실시하였다. 또한 암석 투과도 개선을 위한 균열 지지제(proppant)를 주입해 응력조건별 균열 암석 투과도 변화 양상을 분석하였다. 실험결과, 층리 암석투과도에서는 층리가 존재하지 않는 암석 시료가 응력에 가장 민감하게 반응하였으며, 균열 암석 투과도에서는 균열 지지제 주입 유무에 따라 암석 투과도 값이 크게 달라지는 것을 확인 할 수 있었다.