• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.135-138
• /
• 2003

Recently, sandwich structures have been widely employed in load bearing structures due to their high specific stiffness and high specific strength. Some sandwich structures are subjected to not only static loads but also impact loads which might induce failure of structures at far less load than expected. Since sandwich structures can fail in various modes, estimation of the impact energy absorption is difficult. In this work, the impact failure modes and the impact energy absorption characteristics of the sandwich beams were predicted by the FE analysis and confirmed by the impact test. From the analytic and experimental results, the impact failure mode map was constructed with respect to non-dimensional parameters.

• Journal of Mechanical Science and Technology
• /
• v.17 no.5
• /
• pp.668-678
• /
• 2003

For the purpose to facilitate development of high-speed spindle units (SUs) running on rolling bearings, we have developed a beam element model, algorithms, and software for computer analysis of thermal characteristics of SUs. The thermal model incorporates a model of heat generation in rolling bearings, a model of heat transfer from bearings, and models for estimation of temperature and temperature deformations of SU elements. We have carried out experimental test and made quantitative evaluation of the effect of operation conditions on friction and thermal characteristics of the SUs of grinding and turning machines of typical structures. It is found out that the operation conditions make stronger effect on SU temperatures when rpm increases. A comparison between the results of analysis and experiment proves their good mutual correspondence and allows us to recommend application of the models and software developed for design and research of high-speed SUs running on rolling bearings.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.231-235
• /
• 1999

Cooling characteristics of cooling jacket for spindle system with built-in motor are studied. for the analysis, three dimensional model for the cooling jacket is built by using finite volume method. The three dimensional model includes the estimation on the amount of heat generation of bearing and built-in motor and the thermal characteristic values such as heat transfer coefficients on the boundary. The temperature distributions and the cooling characteristics are analyzed by using the commercial software FLUENT. Numerical results show that stream-wise cross section area and flow rate are important factors for cooling characteristics of cooling jacket. Cooling performance of cooling jacket is good in condition that stream-wise cross section's horizontal length is close to its vertical one and flow rate is high. This results show that heat transfer is dominated by velocity profile and heat transfer area.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.691-696
• /
• 2000

Cooling characteristics of cooling jacket for spindle system with built-in motor are studied. Three dimensional model was selected for the analysis of the helical-type cooling jacket. This model includes the estimation on the amount of heat generation from bearing and built-in motor and the thermal characteristic values such as heat flux on the boundary. The temperature distributions are analyzed and the cooling by Nusselt number and total heat transfer coefficient. Numerical results show that stream-wise cross section area and flow rate are important factors for cooling characteristics of cooling jacket.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.4
• /
• pp.694-699
• /
• 2011

A closed-form technique is presented for estimating a single source location from a set of noisy time delay measurements between distributed sensors. The localization formula is derived from nonlinear least squares minimization over the unknowns of target range and bearing in polar coordinates. Computer simulation results are provided for the purpose of performance analysis. Constrained least squares minimization method with prior source location information is also discussed.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.15-17
• /
• 2002

자기 베어링을 구동하는 코일은 회전축의 위치 정보를 가지고 있다 따라서 코일의 인덕턴스를 알 수 있으면 위치 센서를 쓰지 않고도 회전축의 위치를 알아낼 수 있다. 본 논문에서는 코일에 고주파 신호를 주입하여 인덕턴스를 알아내고, 이를 통해 회전축의 위치를 추정하는 방법을 제안하고. 실험을 통해 이를 검증한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.985-988
• /
• 2002

The Spindle-]fearing System is very important unit for geometrical accuracy in machine tools. To improve effectively the weak point of spindle system, it is necessary that the contribution ratio of spindle core parts to static and dynamic stiffness is clarified. In this paper, static contribution ratio of core parts is calculated by overlapping static deformation of basic spindle design with one flexible parts. The dynamic contribution ratio for natural frequency and dynamic deformation at spindle end is obtained by calculating correlation between original and basic spindle deformation, by curve fitting with regressive method. It is proved the validity of estimation result is correct.

• International Journal of Automotive Technology
• /
• v.7 no.6
• /
• pp.757-762
• /
• 2006

Reliability of automotive parts has been one of the most interesting fields in the automotive industry. Especially, a small DC motor was issued because of the increasing adoption for passengers' safety and convenience. For several years, small DC motors have been studied and some problems of a life test method were found out. The field condition was not considered enough in the old life test method. It also needed a lot of test time. For precise life estimation and accelerated life test, new life test procedure was developed based on measured field condition. The vibration condition on vehicle and latent force on fan motor shaft were measured and correlated with each other. We converted the acceleration data into the load data and calculated the equivalent load from integrated value. We found the relationship which can be used for accelerated life test without changing the severity by using different loading factors.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.3-6
• /
• 1988

The UCERSS algorithm is an extended MUSIC which is used to estimate incident angles of multiple wide band signals. The purpose of this paper is to extend the UCERSS in order to estimate the direction of arrivals of multiple wide band signals in multipath environment. The modifications of the UCERSS result in the wide band spatial smoothing and the UNSS approaches. Computer simulation results indicate that the performances of the UNSS are superior to those of the UCERSS and the wide band spatial smoothing method.

• Architectural research
• /
• v.3 no.1
• /
• pp.61-70
• /
• 2001

The paper is intended to propose design strength of slender steel reinforced beam-columns by using the modified superposed method. The design of composite members is carried out by a superposed strength method in AIJ (Architectural Institute of Japan) design method. The bearing capacities of the steel part and the concrete part have to be determined separately and then added to a combined capacity. Authors have proposed a new superposed method in a modified form for the slender composite beam-columns and reinforced column. The modified superposed method is adopted for the slender steel reinforced beam-columns. Validation of the modified superposed method is undertaken by comparison with analytical results calculated assuming a sine curve deflected shape of the beam-columns, and with the test results conducted in Japan.