• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.376-381
• /
• 2004

A rig was constructed to test the performance characteristics and compare the hydraulic forces exerted on a centrifugal type artificial heart impeller. A conventional shaft. seal and bearing system. while driven by a small electric motor. supported the impeller which was separated from the pump casing by a six degree of freedom force transducer (JR3 Ine). Radial (x. y) and axial (z) hydraulic forces were recorded and compared. At physiological operating conditions. the results indicate that the double entry/exit centrifugal pump encounters a smaller radial force and significantly reduced axial thrust. These experimental results are valuable in the design of a magnetic bearing system to suspend the impeller of a centrifugal artificial heart pump. This experimental technique may also be applied to evaluate the required capacity and predict the lifetime of contact bearings in marine pumps.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.7 s.238
• /
• pp.955-963
• /
• 2005

This research investigates dynamic characteristics of a linear motion (LM) guide through a experimental result and theoretical analysis. The stiffness in the LM guide is determined by the preloading due to the minus clearance between the ball bearing and the contact surface and it can be derived by Hertzian contact theory and the nonlinear motion of equation. The vibration analysis is performed using Lagrange equations and its result agrees with the experiment result. Using the sensitivity analysis on design parameters such as the contact angles of ball bearings and the eccentricity of mass center, the variation of the natural frequencies can be predicted.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.3
• /
• pp.44-51
• /
• 1997

Unsteady-state temperature distributions and thermal deformations of the spindle of a high precision lathe are studied in this paper. Three dimensional model is built for analysis, and the amount of heat generation of bearing and the thermal characteristic values including heat transfer coefficient are estimated. Temperature distributions and thermal deformations of a model are analyzed using the finite element method and the thermal boundary values. Numerical results are compared with the measured data. The results show that the thermal deformations and the temperature distributions of the dpindle of a high precision lathe can be reasonably estimated using the three dimensional model and the finite element method.

• Tribology and Lubricants
• /
• v.18 no.1
• /
• pp.42-48
• /
• 2002

Experiments were conducted to determine the structural dynamic characteristics of bump foil bearing. The housing of the bearing on the journal was driven by two shakers which were used to simulate dynamic forces acting on the bump foil strips. Three different bump foils(Cu-coated bump, silicon bump, viscoelastic bump) are tested and the dynamic coefficients of three bump foils compared, based on the experimental measurements for a wide range of operating conditions. From the test results, the high damping coefficients of viscoelastic bump are achieved and the possibility of the super-bending-critical operation is suggested.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.03a
• /
• pp.9-16
• /
• 1995

The thermal deformation of machine tool spindle influences the performance of the manufacturing systems for precision products. In this research thermal analysis of a high speed machine tool spindle with the rolling bearing and the built-in motor is carried out using Finite Difference Method. The thermal boundary conditions describing the hear generation in the bearing and built-in motor are considered in the simulation. And various convective boundary conditions are assumed with the empirical formula in the references. From the simulation results the characteristics of each element affecting the dynamic thermal behaviour of the machine tool spindle systems have been clarified. This model can be well applied to the future development of the high speed spindle systems.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.282-289
• /
• 2001

Experiments were conducted to determine the structural dynamic characteristics of bump foil bearing. The housing of the bearing on the journal was driven by two shakers which were used to simulate dynamic forces acting on the bump foil strips. Three different bump foils(Cu-coated bump, silicon bump, viscoelastic bump) are tested and the dynamic coefficients of three bump foils compared, based on the experimental measurements for a wide range of operating conditions. From the test results, the high damping coefficients of viscoelastic bump are achieved and the possibility of the super-bending-critical operation is suggested.

• Tribology and Lubricants
• /
• v.18 no.5
• /
• pp.333-338
• /
• 2002

Results of theoretical investigations on acoustical properties of hydrodynamic journal bearings are presented. Nonlinear analysis including rotor imbalance is performed for a rotor-bearing system in order to obtain acoustical properties of hydrodynamic journal bearings. Furthermore, a cavitation algorithm, implementing the Jakobsson-Floberg-Olsson boundary condition, is adopted to predict cavitation regions in a fluid film. Acoustical properties of hydrodynamic journal bearings are identified through frequency analysis of oil pressure fluctuation calculated from the nonlinear transient analysis. The results show that the acoustical frequency spectra of the fluid film are pure tone spectra, containing the frequency of the shaft rotation and its super-harmonics. The analysis also shows that super-harmonics are predominant at the neighborhood of the fluid film reformation and rupture regions.

• Tribology and Lubricants
• /
• v.12 no.2
• /
• pp.20-31
• /
• 1996

Pressures in compression pockets consists of two identical spiral scrolls are influenced by gas flow resistance in discharge process and leakages in radial and tangential directions between two scroll wraps. In this paper, considering geometrical characteristics of these members, flow resistance and refrigerant gas leakage losses, pressure variations in compression pockets are calculated. For a scroll compressor model with fixed crank mechanism, acting load on crankshaft is analyzed. And, for a vertical type crankshaft-journal bearing system used in scroll compressor, nonlinear transient response is calculated including nonlinear fluid film reaction forces of journal bearings.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.11-15
• /
• 2002

This paper presents the thermal characteristic analysis of a high-speed HMC with spindle speed of 50,000rpm. The spindle is supported by two radial and axial magnetic bearings. and the built-in motor is located between the axial and rear radial magnetic bearings. The X-axis and Y-axis feeding systems are composed of linear motor and linear motion guides, and the Z-axis feeding system is composed of servo-motor, ballscrew and linear motion guide. The thermal analysis model of high-speed HMC is constructed by the finite element method, and the thermal characteristics in the design stage are estimated based on the temperature distribution and thermal deformation under the conditions related to the heat generation of built-in motor, magnetic bearings, linear motors, servo-motor, ballscrew, and so on.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.1
• /
• pp.27-33
• /
• 1996

Metallographic observation was carried out by scanning and transmission electron microscopy to evaluate microstructural characteristics of partially austenitized and isothermally transformed 1.0C-1.5Cr bearing steel. It was observed that lower bainite formed in the local region of specimen partially austenitized and isothermally held at $250^{\circ}C$ for 1/3 hr and formed in almost all area of the specimen isothermally held at $250^{\circ}C$ for 2 hrs. Lower bainitic carbides with midrib was also observed in the specimen partially austenitized and isothermally held at $250^{\circ}C$ for 4 hrs. Midrib was nearly carbide-free region and thicker in the vicinity of spherical carbides than the other region. Lengthening speed of lower bainitic carbides was remarkabey increased at isothermal holding time ranging from 2 hrs to 4 hrs.