• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.2
• /
• pp.198-205
• /
• 2001

Recently, almost all hard disk drives employ the rotary actuator system. The performance of an HDD depends on the accuracy and speed of tracking motion. We study the dynamics of head-suspension assembly during track seek. We develop the numerical analysis program to study the dynamic characteristics of HDD suspension system considering the air bearing effects. The track seek simulation by using the developed program helps to estimate the effect of the suspension vibration on the air bearing dynamics. We calculate the behaviour of the air bearing for the given track seek profile and calculate the positioning error during track seek process due to the lateral deflection of the suspension.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.97-98
• /
• 2014

Vibration signal has been widely utilized in the diagnostics of rotating mechanical system. Diagnostics systems in rotating machinery are depends on the vibration data which are acquired from the system. However, the characteristics of acquired data can be vary according to the position of anomaly installed or the position of data acquired. In this research, the coordinate transform of journal bearing vibration signal was proposed to overcome the limitation mentioned above. Journal bearing systems are equipped two gap sensors with ninety degree angles, and it can enable to generate coordinate transformed signals in arbitrary angle domain. More abundant information for each normal or anomaly conditions are obtained from coordinate transformation than only the data of the existing measuring position, then we have developed a reliable and robust diagnosis algorithm for journal bearing system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.888-891
• /
• 2002

This paper presents the lubrication characteristics of a disk type wavy thrust bearing. The hydrodynamic pressure distributions in the fluid film are numerically solved the Reynolds equation and then the bearing load capacity and friction forces acting on the disk are calculated. Especially the effects of number and amplitude of the circumferential waves are investigated for tilted operating conditions. The results showed that the load capacity increases with wave amplitude and optimum wave number exists for given design conditions. Therefore the results can be applied to enhance the lubrication performance of thrust bearing adopted in the scroll compressor.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1729-1734
• /
• 2008

This study developed a new separated shperical bridge bearing that can be used for replacement of existing bridge bearings without crushing bearing-concrete. The separated spherical bearing have the upper and lower sole plate connected by bolts to the upper plate under bridge-girders and the lower plate on bearing-concrete. The targets of the separated spherical bearing are the maximum 3 mm of up-lifting height during replacement and the maximum required time of 30 minutes. Four separated spherical bearings are manufactured and replaced the existing bearings of a railway bridge in service and the replacing tests was performed. The number of the tests is two and the target of maximum 3 mm and 30 minutes was satisfied.

• Journal of the Korea Concrete Institute
• /
• v.24 no.2
• /
• pp.129-136
• /
• 2012

Compression splices are required for all compression members in almost all of the floors in high-rise buildings. Therefore, a clear understanding of the behavior of compression splices can provide a rational design of compression splices. Tests of compression splices with bearing only and bond only cases were conducted to investigate the component resistance characteristics of compression splices. Test results showed that the circumferential tensile stresses induced by bearing and bond overlapped at the end of the splice length deterred bond and bearing splices from developing target splicing strength when both normal bond and bearing splices were used. In particular, the bearing strength was more significantly reduced than the bond strength since the bearing relied on the limited area near the end of the splice length. However, the strength of the normal splice was always higher than the strength of the bond only or the bearing only case. Consequently, the study results showed that splice strength in compression cannot be improved by means of removing bond or bearing. In addition, the bond strength in bond only splices was nearly same as the bond strength in tension splices and the strength increase of compression splice is attributed to end bearing only characteristic.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.82-86
• /
• 2002

The thermal characteristics of high-speed air spindle system with built-in motor are studied. Experiment and finite difference method analysis obtain temperature rise and temperature distribution of housing. For the analysis, air fluid film model is built and temperature rise and distribution in thermal steady state are computed for each rotational speed. Generally, it is said that the heat generation of air bearing is negligible. But the heat generation in air film by heat dissipation can not be negligible especially into high-speed region of the journal. In case that the heat generation of air spindle system is high, natural frequency of the spindle system becomes lower when the thermal state is in steady-state and it means the changes of air bearing stiffness due to the change of bearing clearance. It is shown that the temperature rise of air spindle system causes thermal expansion and induces the variation of bearing clearance. In consequence the stiffness of air bearing becomes smaller.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.91-93
• /
• 2011

This paper is presented for the performance of the Fluid Dynamic Bearing(FDB) by the groove design and the tooling condition. Recently, spindle motors which require smaller size, lower sound noise, lower vibration, and higher speed of the rotation have been placed in high value-added products including Digital Lightening Processors(DLP), Hard Disk Drives(HDD), and ODDs. The spindle motors using the sintered porous metal bearing have higher vibration and acoustic noise by dry contact and large tolerance of the bearing parts. The Fluid Dynamic Bearing (FDB) with grooves is appropriate for spindle motors adequate in regards to mechanical vibration and acoustic noise. The paper shows the performance comparisons of between sintered porous metal bearing and FDB, and each FDBs according to the tooling deviations of grooves by the Finite Element Analysis(FEA) of the mechanical field. This paper shows the methods to make the grooves, the groove's depth, and the prototype of the motor with the fluid dynamic bearing. The performance characteristics of the grooves with the FDB are verified by the experimental results.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.1955-1962
• /
• 2017

Induction motors are a workhorse for the industry. The condition monitoring and fault analysis are the main concern for the engineers. The bearing is one of the vital segment of the induction machine and the condition of the whole machine is decided based on the condition of the bearing. In the present paper, the vibration signal of the bearing has been used for the analysis. The first line of action is to perform a statistical analysis of the vibration signal which gives trends in signal. To get the location of a fault in the bearing the second action is to develop an index based on Wavelet Packet Transform node energy named as Bearing Damage Index (BDI). Further, Teager-Kaiser Energy Operator (TKEO) has been calculated from higher index value to get the envelope and finally Power Spectral Density (PSD) has been applied to identify the fault frequencies. A performance index has also been developed to compare the usefulness of the proposed method with other existing methods. The result shows that the strong amplitude of fault characteristics and its side bands help to decide the type of fault present in the recorded signal obtained from the bearing.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.3
• /
• pp.7-12
• /
• 2010

In the case of hydraulic piston motor, hydrostatic bearing is designed to be adapted the hydrostatic bearing for the relative lubrication in the structural design. It's available to make it highly efficient and that's why it's widely used. The thing which largely influence the high pressure, the high efficiency, and the life is the hydrostatic bearing between a shoe and a swash plate. In this study, with the most general "hydrostatic bearing shoe" that has one recess as the subject of this research, I designed and made the 4 kind of piston shoe that have different orifice diameter each other, and studied the features of the hydrostatic bearing by observing the change of the leakage flow rate, the torque and the volumetric efficiency through experiments on the changes of the pressure & the speed of the revolution. As a result, the bigger diameter of the orifice, the less torque. And with an increase of the orifice diameter under the high pressure, the leakage flow rate decreased remarkably. Also it was observed the leakage flow rate increased linearly according to the increase of the supply pressure.

• Journal of Mechanical Science and Technology
• /
• v.17 no.2
• /
• pp.246-253
• /
• 2003

The tribological mechanism between the valve plate and the cylinder block in oil hydraulic axial piston pumps plays an important role on high power density. In this study, the fluid film thickness between the valve plate and the cylinder block was measured with discharge pressure and rotational speed by use of a gap sensor, and a slip ring system in the operating period. To investigate the effect of the valve plate shapes, we designed two valve plates with different shapes . the first valve plate was without a bearing pad, while the second valve plate had a bearing pad. It was found that both valve plates behaved differently with respect to the fluid film thickness characteristics. The leakage flow rates and the shaft torque were also experimented in order to clarify the performance difference between the valve plate without a bearing pad and the valve plate with a bearing pad. From the results of this study, we found out that in the oil hydraulic axial piston pumps, the valve plate with a bearing pad showed better film thickness contours than the valve plate without a bearing pad.