• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.166-171
• /
• 2001

An electric drill is a handy tool used in a machine shop, which consists of motor, gear, bearing, shaft, and case, i.e., a gear driving system. Low level vibration and noise of the electric drill can bring the assurance of the quality and reliability of the machine. The vibration sources of the electric drill should be investigated for the reduction of the vibration and noise of the system. Through the experiments in a laboratory and the various signal processing procedure for the measured vibration and sound signals, the characteristics of the vibration and noise of the electric drill are investigated. And its propagation path is sought using partial coherence technique.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.593-598
• /
• 2008

In the present study, degradation characteristics of pumps in nuclear power plants were investigated to provide the information of degradation mechanism and stressors. The failure records of pumps for the periods 2000 to 2006 on INPO(Institute of Nuclear Power Operations) EPIX(Equipment Performance and Information Exchange System) DB were reviewed. The 1,834 failure records reveal that the critical areas of pump failures are bearing, mechanical seal, gasket/o-ring, shaft, impeller, coupling and packing. Based on the failure rate of critical areas, the important degradation mechanism and stressors were determined. Additionally, the relationship between degradation mechanism and stressors such as wear was examined. Finally, the monitoring parameters related to degradation and stressors were discussed for the future development of degradation evaluation and prognosis technology of pumps.

• Journal of the Korean Society for Railway
• /
• v.9 no.3 s.34
• /
• pp.298-304
• /
• 2006

An active application of concrete track is being expected for the future constructions of Korean railroad. For the successful concrete track construction and design in earthwork areas, the roadbed behavior should be reasonably estimated using the proper analysis method. In this paper, behaviors of concrete track on the reinforced roadbed constructed with the standard stiffness and depth were estimated thorough numerical analyses and field measurements. A three dimensional finite difference method was employed to model the concrete tracks and subground. The settlement and vertical pressures caused by train load were estimated by the numerical method and compared with the field measurement results. The bearing characteristics of roadbed were presented and the proper method for the analysis of concrete track was proposed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.49-58
• /
• 1998

An experimental study was performed to discover the effect of adsorbed moisture on the rolling resistance behavior of pure silver coated 52100 bearing steel. Plasma surface modifications were performed on the silver coated specimen to change the wetting characteristics. Experiments using a thrust ball beating-typed roiling test-rig were performed under vacuum, dry air and various tmmidity conditions. Results showed that the changes in the wetting characteristics influenced remarkably on the silver particle agglomeration and resulted in the different behavior of rolling resistance with humidity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.8
• /
• pp.885-893
• /
• 2006

A dynamic model of turbo air compressor having multi-helical gear pairs is developed by transfer matrix method. The model accounts for the shaft and bearing flexibilities, gyroscopic effects and the force couplings among the transverse, torsion, and axial motions due to gearing. The program which can be used to analyze and predict the vibrational characteristics by the mass unbalance of the rotors and gear transmission error of turbo compressor is developed with this system model We expect this developed program to contribute the reduction of the vibration/noise on turbo compressor in the field of both design and manufacturing and can be used as a basic sub-program for CAD/CAM of low-noised gear teeth also.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.193-197
• /
• 2008

Array of micro-dimple on polyoxymethylene (POM) surface was fabricated using Q-switched Nd:YAG laser and its characteristics were studied in terms of heat affected zone (HAZ), dimple geometry, and the effect of specimen surface roughness. Process parameters such as lamp current, process time, and the stream of air in order to minimize HAZ and flow of molten polymer into cavity were extensively studied in this work. Dimple geometry was further investigated by 3-D optical microscopy to provide deep insight into morphological analysis near the dimples. This paper also presents the applicapability of micro-dimples in polymeric tribological system, such as a thrust bearing. Micro-dimples were expected to provide low coefficient of friction and enhanced lubricity at the sliding interface.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.144-148
• /
• 2005

Cylinder frame manufactured by casting is assembled with the components such as cylinder head, cylinder liner and main bearing cap, etc. The mechanical contact between all of the neighboring components due to bolt tightening was taken into consideration. The loads used in structural analysis were the bolt tightening forces induced by hydraulic jack and the dynamic forces calculated from kinematic analysis. The difference of forces between the neighboring cylinders was taken into account. The maximum stress, stress amplitude and mean stress calculated from the results of structural analyses were used to evaluate the static and fatigue strength. Gray cast iron which is material of cylinder frame has the material characteristics of very small elongation and different strength in tension and compression. Based on such an material characteristics, the strength evaluation of cylinder frame was carried out with in-house program developed internally.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.441-446
• /
• 2001

In this paper the effect of bump compliance, load, and the number of pad on the lift-off speed is studied. When the load is greater and bump compliance lower, the shaft is lifted off at higher rotating speed. And when the load is applied near the center of pad, lift-off speed is lower. When the number of pad increases, the lift-off speed is higher. The lift-off characteristics can be used to lengthen the lift time of the coating and design the rotating machinery supported by bump bearings.

• Tribology and Lubricants
• /
• v.25 no.3
• /
• pp.192-196
• /
• 2009

This paper presents the hardness and wear characteristic of bronze metals, which are manufactured by a sintering process with a high pressuring technology. A bronze metal with a high hardness and anti-wear properties is usually used for a high pressure cylinder and a pin-bush bearing. The new bronze metal in which is manufactured for this experimental study shows very high hardness of 192${\sim}$220 Hv compared with that of a conventional bronze metal of 120${\sim}$140 Hv. The high hardness of new bronze metals is strongly related to the radical reduction of wear volumes and an improved surface roughness of operated worn surfaces. As explained by previous many research works, the improved hardness of nonferrous metals may increase a load-carrying capacity and anti-wear properties of tribological components.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.257-262
• /
• 2003

Base isolation bearings are known as an effective system to Protect bridges from the earthquake damage. There are many types of base isolation bearings in the market. Among them, steel hysteretic damper, made of mild steel and one of the oldest ones, has some good features. Since steel hysteretic damper is made of steel and has simple structure, it is cheeper and easier to maintain than other types. Despite the advantages, steel hysteretic damper with pin-type elements has no application in Korea. The steel hysteretic damper with pin-type elements are tested to examin the basic characteristics and to evaluate antiseismic performance. In this paper, the results of the test are presented.