• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.2
• /
• pp.186-193
• /
• 2014

This paper presents characteristic analysis of underwater bearing for canned type electric water pump. Characteristic analysis of underwater bearing was performed using self-developed performance tester, which capable of torque change, noise change, motor speed change and abrasion loss test with respect to temperature change of underwater bearing. The performance tester can be monitored in real time by designing the control unit using the Labview program. The performance experiment was performed through comparison of the silicon carbide (SIC) and the carbon bearing. From the experiment results, performance of SIC bearing was better than carbon bearing at the abrasion and temperature experiment.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.399-407
• /
• 1986

본 연구에서는 공기역학 탄성베어링의 설계에 필요한 기본이론에 대하여 고찰 하고 그의 신빙성을 그러한 베어링에 지지된 고속회전축의 진등측정을 통하여 검토하 고저 한다. 탄성베어링의 한 예로써 여러 개의 탄성박판이 겹쳐 저어널을 지지하는 겹판베어링(

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.12a
• /
• pp.63-69
• /
• 1993

In this paper the characteristics of Hydrostatic Bearing of piston of cylinder are investigated . The dynamic characteristic equations of piston considering both parallel and rotational motion and time dependent modified Reynolds Equation are analyzed and the dynamic pressure distribution of oil film is numerically calculated by perturbation method and finite difference method. and the atatic analysis is carried out. so, the influence of design parameter of piston on the characteristic of bearing is analyzed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.229-234
• /
• 2003

As electrorheological fluid(ER fluid) has a characteristic that apparent viscosity varies when electric field applied, so rheological characteristic(yield stress & viscosity) changes in proportion to the electric field applied and the response time is very short within a few miliseconds . In case of using ER fluid for journal bearing as lubricant, it is estimated that it's possible to realize very effective journal bearing system that is not complicate and has a very quick response time. It is necessary to examine the influence of rheological characteristic that varies with electric field applied on bearing characteristic to apply ER fluid to journal bearing, however there are few studies for about that. As for the journal bearing, it comes under high shear flow mode that has shear rate range of $10^3\~10^4s^{-1}$ because rotational speed is very high and clearance is small. But most of the studies for about ER fluid issued until now is about the range of $10\~10^2s^{-1}$. So, there are a lot of difficulties to understand the characteristic offish shear flow mode and furthermore it is restricted to make an experiment for about the characteristic of ER fluid because of the limitation of experimental equipment. The equipment was prepared to make an experiment lot high shear flow mode that has the range of $10^3\~10^4s^{-1}$ using ER fluid that is composed of silicon oil with dispersed particle of starch. Using the above system, the fluid characteristic of ER fluid was studied.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2518-2534
• /
• 1993

Fracture behavior of carbon/epoxy laminates under pin loading is studied experimentally and analytically. Effects of ratios of specimen width to hole diameter and edge distance to hole diameter on bearing strength are investigated. Characteristic length of the laminates obtained using HK model has good agreement with the experimental data. The larger hole size induced, the lower bearing strength is measured under pin loading . The bearing strength and failure mode could be predicted using HK model and Zhangs analytical solution of stress distribution around a pin loaded hole. Chamis' prediction method of bearing strength is also considered to predict failure mode and bearing strength. A modification of Chamis' method is made using the factor of rupturc. The predicted bearing strength by the modified method is reasonably close to the experimental data.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.111-121
• /
• 1997

An investigation was performed to study the predicting the joint strength of mechanical fasteners. Bearing failure is most important failure mode for designing joint. So in this study, the prediction method in consideration with bearing failure was chosen. In the proposed method, the characteristic length is combined with the Yamada-Sun failure criterion, Tsai-Hill failure criterion and characteristic length for Tension and Compression is determined from investigation. Especially the length of compression is determined from the "bearing failure test" that newly conceived to take bearing failure into consideration. The proposed prediction method was applied to quasi-isotropic carbon/epoxy joint showing net-tension and bearing failure experimentally. Good agreement was found between the predicted and experimental result for each joint geometry. geometry.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.119-121
• /
• 2003

The magnetic bearing is an important element for high-speed system, such as semiconductor equipment and machine tools. Particularly, The homopolar magnetic bearing has the advantages of lower power losses, more space for heat dissipation and coil winding. This paper deals with analysis and comparison of the homopolar magnetic bearing according to four different PM structures. On the basis of these results, we find one homopolar magnetic bearing superior to the others. finally, this paper derive force characteristic equation for this model and deals with comparison of between analytical and FE results.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.202-205
• /
• 2004

A numerical method is presented to determine the characteristic lengths for the failure analysis of composite joints without characteristic length tests. In the conventional methods, compressive characteristic length was determined from the result of a combined bearing test and finite element analysis. The present study, however, shows that the same compressive characteristic length can be obtained by numerical calculation without the bearing test. A new method to define the tensile characteristic length is also introduced so that the tensile characteristic length is numerically determined without the tensile test. Failure loads based on the numerically calculated characteristic lengths are validated by the test results for composite joints

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.04a
• /
• pp.269-279
• /
• 1997

An investigation was peformed to study the predicting the joint strength of mechanical fasteners. Bearing failure is most important failure mode for designing joint. So in this study, the prediction method in consideration with bearing failure was chosen. In the proposed method, the characteristic length is combined with the Yamada-Sun failure criterion, Tsai-Hill failure criterion and characteristic length for Tension and Compression is determined from investigation. Especially the length of compression is determined from the "bearing failure test" that newly conceived to take bearing failure into consideration. The proposed prediction method was applied to quasi-isotropic carbon/epoxy joint showing net-tension and bearing failure experimentally. Good agreement was found between the predicted and experimental result for each joint geometry.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.131-136
• /
• 2003

Five expensive sensors are necessary to control a magnetic bearing system. The sensor price rate of magnetic bearing system is high. So it is necessary that cheap and good sensor is developed. The optical fiber displacement sensor is adaptive to satisfy this condition. We can design magnetically suspended spindle based on static characteristic of optical fiber displacement sensor developed. The controller can be designed by decoupled feedback PD. Therefore, it is simpler than any other controller comparatively.