• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.3
• /
• pp.238-243
• /
• 2008

Several experimental techniques for identifying the noise sources distributed over a moving vehicle have been developed recently and are used to design a low noise vehicle. The beamforming method, which uses phase information between several microphones to localize the source position, is proved to be one of the promising techniques applicable even under complicated test environments. In this study a beamforming algorithm is developed and applied to measure the dominant noise sources on a passenger car passing by. Unlike the acoustic signals from a stationary noise source, the sound generated from a moving source is distorted due to the Doppler effects. The information about the speed and relative position of the vehicle are used to eliminate the Doppler effects from the measured acoustic signal by using a de-Dopplerization algorithm. The noise generated from a moving vehicle can be grouped in many ways, however, tire noise and the noise generated from the engine are distinguishable at the speeds being tested.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.11A
• /
• pp.1013-1020
• /
• 2008

Cognitive radio(CR) techniques have been considered as a strong solution of frequency scarcity due to the limitation of frequency resource, In this paper, an orthogonal beamforming method is proposed that enables cognitive radio systems to coexist with a primary users' system in the same spectrum and region without causing interference to primary systems. The orthogonal multiple beams for multi-users of CR systems are obtained through the generation of orthogonal subspaces from primary users' channel state information. To increase the sum-rate of the CR systems, the proposed scheme adopts opportunistic radio resource allocation techniques. Simulation results provides that the proposed scheme achieves 2.72bps/Hz, the sum-rate capacity at 20 cognitive users in an area with two antennas at the cognitive radio basestation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.12
• /
• pp.1338-1346
• /
• 2004

The positions of rotating sound sources have been localized by experiments with the Doppler effects removed. In order to de-Dopplerize the sound signals emitted from moving sources, two kinds of signal reconstruction methods were applied. One is the forward propagation method and the other is the backward propagation method. Forward propagation method analyze the source emission time based on the instantaneous distance between sensors and the assumed source position, then the signals are reconstructed with respect to the emission time. On the other hand, the backward method uses time delay to do-Dopplerize the acquired data for the received time of reference. In both techniques. the reconstructed signal data were processed using beamforming algorithm to produce power distributions at the frequencies of interest. Experiments have been carried out for varying frequencies, rotating speeds and the object distances. It is shown that the forward propagation method gives better performance in locating source position than the backward propagation method.

• Journal of Communications and Networks
• /
• v.13 no.4
• /
• pp.327-338
• /
• 2011

With the incitation to reduce power consumption and the aggressive reuse of spectral resources, there is an inevitable trend towards the deployment of small-cell networks by decomposing a traditional single-tier network into a multi-tier network with very high throughput per network area. However, this cell size reduction increases the complexity of network operation and the severity of cross-tier interference. In this paper, we consider a downlink two-tier network comprising of a multiple-antenna macrocell base station and a single femtocell access point, each serving multiples users with a single antenna. In this scenario, we treat the following beamforming optimization problems: i) Total transmit power minimization problem; ii) mean-square error balancing problem; and iii) interference power minimization problem. In the presence of perfect channel state information (CSI), we formulate the optimization algorithms in a centralized manner and determine the optimal beamformers using standard convex optimization techniques. In addition, we propose semi-decentralized algorithms to overcome the drawback of centralized design by introducing the signal-to-leakage plus noise ratio criteria. Taking into account imperfect CSI for both centralized and semi-decentralized approaches, we also propose robust algorithms tailored by the worst-case design to mitigate the effect of channel uncertainty. Finally, numerical results are presented to validate our proposed algorithms.

• Journal of Broadcast Engineering
• /
• v.8 no.2
• /
• pp.136-145
• /
• 2003

This paper proposes a DTV receiver using beamforming techniques to improve indoor and mobile reception. The proposed DTV receiver estimates the directions of arrival (DOAs) of incoming signals using Capon's DOA estimation method and generates an adaptive antenna beam pattern to the estimated DOA of the mainpath signal to Improve the channel condition. After beamforming, a following decision feedback equalizer (DFE) removes the remaining multipath components. The proposed receiver can be implemented with a conventional DTV receiver without anymodification. The performance of the proposed receiver is analyzed with modified Brazilian field test models, which include DOA information of Incoming signals. Simulation results show that the proposed receiver can satisfy the threshold of visibility (TOV) when input signal to noise ratio is slightly over 10 dB.

• ETRI Journal
• /
• v.43 no.3
• /
• pp.389-399
• /
• 2021

In this paper, we propose one-bit feedback-based distributed beamforming (DBF) techniques for simultaneous wireless information and power transfer in interference channels where the information transfer and power transfer networks coexist in the same frequency spectrum band. In a power transfer network, multiple distributed energy transmission nodes transmit their energy signals to a single energy receiving node capable of harvesting wireless radio frequency energy. Here, by considering the Internet-of-Things sensor network, the energy harvesting/information decoding receivers (ERx/IRx) can report their status (which may include the received signal strength, interference, and channel state information) through one-bit feedback channels. To maximize the amount of energy transferred to the ERx and simultaneously minimize the interference to the IRx, we developed a DBF technique based on one-bit feedback from the ERx/IRx without sharing the information among distributed transmit nodes. Finally, the proposed DBF algorithm in the interference channel is verified through the simulations and also implemented in real time by using GNU radio and universal software radio peripheral.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.3
• /
• pp.433-438
• /
• 2017

Containing an Angle-of-Arrival(: AOA) estimation and interference suppression techniques, an adaptive beamformer is one of core techniques for the Signal Intelligence(: SIGINT) which collect various intelligence utilizing cutting edge devices including the radar and satellite. It generates a beam with the directivity in a corresponding direction, to efficiently receive a signal from the specific direction, using antenna array. In this paper, we present the received signal model including interference signals and noise, which can be applied to an input of the signal intelligence satellite system equipped with the AOA estimation and the interference cancellation techniques, and analysis the characteristics of various signals, which can be included in the proposed received signal model. This proposed signal model can be directly applied to the performance evaluation for a variety of beamforming techniques. Also, we verify the spectrum characteristic of the presented received signal model in the frequency domain through computer simulation examples.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.334-337
• /
• 2005

The speech intelligibility is one of the most important factors in communication system. The speech intelligibility is related with speech to noise ratio. To enhance the speech to noise ratio, background noise reduction techniques are being developed. As a part of solution to noise reduction, this paper introduces directional microphone using beamforming method and speech filtering method. The directional microphone narrows the spatial range of processing signal into the direction of the target speech signal. The noise signal located in the same direction with speech still remains in the processing signal. To sort this mixed signal into speech and noise, as a following step, a speech-filtering method is applied to pick up only the speech signal from the processed signal. The speech filtering method is based on the characteristics of speech signal itself. The combined directional microphone and speech filtering method gives enhanced performance to speech intelligibility in communication system.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.1
• /
• pp.187-199
• /
• 2016

In this paper, we consider secure communications in multi-hop relaying systems, where multiple decode-and-forward (DF) relays are located at each individual hop and perform cooperative beamforming to improve physical layer security. In order to determine the cooperative relay beamformer at each hop, we propose an iterative beamformer update scheme using semidefinite relaxation and bisection techniques. Numerical results are presented to verify the secrecy rate performance of the proposed scheme.

• Journal of information and communication convergence engineering
• /
• v.15 no.1
• /
• pp.14-20
• /
• 2017

In this paper, we discuss physical layer security techniques in downlink networks, including eavesdroppers. The main objective of using physical layer security is delivering a perfectly secure message from a transmitter to an intended receiver in the presence of passive or active eavesdroppers who are trying to wiretap the information or disturb the network stability. In downlink networks, based on the random feature of channels to terminals, opportunistic user scheduling can be exploited as an additional tool for enhancing physical layer security. We introduce user scheduling strategies and discuss the corresponding performances according to different levels of channel state information (CSI) at the base station (BS). We show that the availability of CSI of eavesdroppers significantly affects not only the beamforming strategy but also the user scheduling. Eventually, we provide intuitive information on the effect of CSI on the secrecy performance by considering three scenarios: perfect, imperfect, and absence of eavesdropper's CSI at the BS.