• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.1
• /
• pp.135-142
• /
• 1992

In the vibration analysis or submerged of floating bodies such as ship and offshore structures, the coupled system between structure and fluid satisfying the compatibility conditions on the wetted surface should be considered. It is well known that the hydroelastic analysis of structural vibration in contact with fluid can be solved by applying the finite element method to structure and the boundary element method to fluid domain. However such an approach is impractical, because fluid added mass matrix is fully coupled on whole wetted surface. To overcome this shortcoming, an efficient approach based on reanalysis scheme is proposed in this paper. The proposed method can be applied for cases with higher modes lacking 3-D reduction factor J as well as beam-like modes of marine structures. It is well known the traditional method using 2-D added mass and J-factor is good only for beam-like modes with reliable J values. The validity and the calculation efficiency of the proposed method are proved with numerical examples.

• Earthquakes and Structures
• /
• v.12 no.2
• /
• pp.165-175
• /
• 2017

This paper studies soil properties uncertainty and its implementation in the seismic response evaluation of structures. For this, response sensitivity of two 4- and 12-story RC shear walls to the soil properties uncertainty by considering soil structure interaction (SSI) effects is investigated. Beam on Nonlinear Winkler Foundation (BNWF) model is used for shallow foundation modeling and the uncertainty of soil properties is expanded to the foundation stiffness and strength parameters variability. Monte Carlo (MC) simulation technique is employed for probabilistic evaluations. By investigating the probabilistic evaluation results it's observed that as the soil and foundation become stiffer, the soil uncertainty is found to be less important in influencing the response variability. On the other hand, the soil uncertainty becomes more important as the foundation-structure system is expected to experience nonlinear behavior to more sever degree. Since full This paper studies soil properties uncertainty and its implementation in the seismic response evaluation of structures. For this, response sensitivity of two 4- and 12-story RC shear walls to the soil properties uncertainty by considering soil structure interaction (SSI) effects is investigated. Beam on Nonlinear Winkler Foundation (BNWF) model is used for shallow foundation modeling and the uncertainty of soil properties is expanded to the foundation stiffness and strength parameters variability. Monte Carlo (MC) simulation technique is employed for probabilistic evaluations. By investigating the probabilistic evaluation results it's observed that as the soil and foundation become stiffer, the soil uncertainty is found to be less important in influencing the response variability. On the other hand, the soil uncertainty becomes more important as the foundation-structure system is expected to experience nonlinear behavior to more sever degree. Since full probabilistic analysis methods like MC commonly are very time consuming, the feasibility of simple approximate methods' application including First Order Second Moment (FOSM) method and ASCE41 proposed approach for the soil uncertainty considerations is investigated. By comparing the results of the approximate methods with the results obtained from MC, it's observed that the results of both FOSM and ASCE41 methods are in good agreement with the results of MC simulation technique and they show acceptable accuracy in predicting the response variability.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.4
• /
• pp.186-191
• /
• 2014

Double layer films which consisted of aluminum(Al) and magnesium(Mg) have been prepared by e-beam deposition. The structure, alloy phase, and corrosion resistance of the prepared films were investigated before and after heat treatment. The first (bottom) layer fixed with Al, and the thickness ratio between Al and Mg layers has been changed from 1 : 1 to 5 : 1, respectively. Total thickness of Al-Mg film was fixed at $3{\mu}m$. The cold-rolled steel sheet was used as a substrate. Heat treatment was fulfilled in an nitrogen atmosphere at the temperature of $400^{\circ}C$ for 2, 3 and 10 min. Surface morphology of as-deposited Al-Mg film having Mg top layer showed plate-like structure. The morphology was not changed even after heat treatment. However, cross-sectional morphology of Al-Mg films was drastically changed after heat treatment, especially for the samples heat treated for 10 min. The morphology of as-deposited films showed columnar structure, while featureless structure of the films appeared after heat treatment. The x-ray diffraction data for as-deposited Al-Mg films showed only pure Al and Mg peaks. However, Al-Mg alloy peaks such as $Al_3Mg_2$ and $Al_{12}Mg_{17}$ appeared after heat treatment of the films. It is believed that the formation of Al-Mg alloy phase affected the structure change of Al-Mg film. It was found that the corrosion resistance of Al-Mg film was increased after heat treatment.

• Journal of the Korean Vacuum Society
• /
• v.5 no.1
• /
• pp.1-5
• /
• 1996

Noncrystalline films of diamond-like carbon (DLC) have been prepared by laser ablation technique at room temperature. A Q-switched Nd-YAG laser beam with wavelength of 1064 nm and pulse duration of 10 ns was focused onto a graphite target with power densities of about $10^9 W/\textrm{cm}^2$. The physical properties of the resulting films were analyzed with density, hardness, and resistivity measurements. The surface and bonding structure were investigated by atomic force microscopy (AFM), Raman spectroscopy, electron energy loss spectroscopy (EELS).

• Structural Engineering and Mechanics
• /
• v.52 no.4
• /
• pp.723-738
• /
• 2014

Prestressing is the most commonly employed technique in bridges and long span beams in commercial buildings as prestressing results in slender section with higher load carrying capacities. This work is an attempt to study the performance of a minimum weight prestressed concrete beam adopting a non-prismatic section so that there will be a reduction in the volume of concrete which in turn reduces the self-weight of the structure. The effect of adopting a non-prismatic section on parameters like prestressing force, area of prestressing steel, bending stresses, shear stresses and percentage loss of prestress are established theoretically. The analysis of non-prismatic prestressed beams is based on the assumption of pure bending theory. Equations are derived for dead load bending moment, eccentricity, and depth at any required section. Based on these equations an algorithm is developed which does the stress checks for the given section for every 500 mm interval of the span. Limit state method is used for the design of beam and finite difference method is used for finding out the deflection of a non-prismatic beam. All the parameters of nonprismatic prestressed concrete beams are compared with that of the rectangular prestressed concrete members and observed that minimum weight design and economical design are not same. Minimum weight design results in the increase in required area of prestressing steel.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.63-66
• /
• 2003

It is experimentally shown that a $TiO_2$ film on Si(111) substrate was prepared by using the technique of D.C. reaction sputter deposition with $Ar^{+}$ ion beam bombardment, and a layer-like structure was observed from the depth profile of the interface between $TiO_2$ film and Si substrate with Scanning Electron Microscopy and Electron Probe. It was also surprisingly discovered that Ti atoms could be detected at about 9 $\mu$m depth. The $TiO_2$-Si interface bombarded by $Ar^{+}$ ion beams revealed multi-layer structures, a mechanism might be caused by defect diffusion, impurity and matrix relocation. Multi-relocations of impurity and matrix atoms were as a result of profile broadening of the $TiO_2$-Si interface, and the spread due to matrix relocation in this system is shown to exceed much more the spread due to impurity relocation.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.206-222
• /
• 2015

This work uses different finite element approaches to the free vibration analysis of reinforced shell structures, and a simplified model of a typical launcher with two boosters is used as an example. The results obtained using a refined one-dimensional (1D) beam model are compared to those obtained with commercial finite element software. The 1D models that are used in the present work are based on the Carrera Unified Formulation (CUF), which assumes a variable kinematic displacement field over the cross-sections of the beam. Two different sets of polynomials that correspond to Taylor (TE) or Lagrange (LE) expansions were used. The analyses focused on three reinforced structures: a stiffened panel, a reinforced cylinder and the complete structure of the launcher. The frequencies and natural modes obtained using one-dimensional models are compared to those obtained from classical finite element analysis. The classical FE models were built using a beam-shell or solid elements, and the results indicate that the refined beam models can in fact be used to investigate the behavior of very complex reinforced structures. These models can predict the shell-like modes that are typical of thin-walled structures that cannot be detected using classical beam models. The refined 1D models used in the present work provide results that are as accurate as those from solid FE models, but the 1D models have a much lower computational cost.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.11A
• /
• pp.1056-1063
• /
• 2005

In this paper, we develop a dual beam automotive laser radar system which improve the defect of conventional unipolar one beam laser scheme. We introduce an SNR improving method using bipolar signal synthesizing scheme from two unipolar signals at the receiving unit via differential structure by allocating bipolar m-sequence into the two laser wavelengths, which have similar property like 2-D OOC, and investigate its performance. Simulation results show that the proposed dual beam scheme can have 3dB SNR improvement as compared with conventional unipolar signaling laser radar system. Also, we show the simple interference rejection scheme using differential structures. The proposed scheme have a merit to obtain additional 3dB SNR gain applied into the excellent results based on unipolar optical signal studied lately.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.81-88
• /
• 2000

Unlike structures in the air, the vibration analysis of a submerged or floating structure such as offshore structures or ships is possible only when the fluid-structure interaction is understood, as the whole or part of the structure is in contact with water. Specially, the importance of the added mass is not necessary to say like the submerged vehicle, all of the hull body, is positioned in the water. This paper introduce two method to find natural frequency in consideration of fluid-structure modal coupled vibration analysis. The purpose of this study is to analyze of the vibration characteristic of submerged vehicle to obtain the anti-vibration design data, which could be used in the preliminary design stage data. Underwater pressure hull of submerged vehicle is used as the model of this study. The F.E.M model is meshed by shell and beam element. Also, considering of the inner hull weight, mass element is distributed in the direction of hull length. Numerical calculations are accomplished using the commercial B.E.M code. The characteristics of natural frequency(eigenvalues), mode shape(eigenvectors) and frequency-displacement response are analyzed. The results of this study will be used as the useful design data in preliminary anti-vibration design stage.

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.285-286
• /
• 2007

This paper presents a robust controller in order to handle the guide rail vibrations of Bridge Inspection System. While a Bridge Inspection Robot moves on guide rails with vibration by weight occurs. Therefore, Guide rail as structure like cantilever beam appears vibration by weight of Bridge Inspection Robot. The Z axis of Bridge Inspection Robot operates with Scissors structure. Bridge Inspection Robot is used 'PID Controller based on Sliding Mode control' for position control with Z axis. At the result of, this paper is applied to simulation about position control regarding vibration to occur with Z axis.