• Journal of the Korean Society for Advanced Composite Structures
• /
• v.1 no.1
• /
• pp.9-15
• /
• 2010

In this paper, A reinforced concrete slab bridges is analyzed by the composite laminates theory. Both the geometry and the material of the cross section of the reinforced concrete slab bridge are considered symmetrical with respect to the mid-surface so that the bending extension coupling stiffness, Bij = 0, and D16 = D26 = 0. Each longitudinal and transverse steel layer is regarded as a lamina, and material constants of each lamina is calculated by the use of rule of mixture. This slab with simple support is under uniformly distributed vertical and axial loads. In this paper, the finite difference method and specially orthotropic laminates theory are used for analysis. The result of specially orthotropic laminates theory analysis is modified to obtain the solution of the beam analysis. The result of this paper can be used for reinforced concrete slab analysis by the engineers with undergraduate study in near future.

• Steel and Composite Structures
• /
• v.13 no.4
• /
• pp.327-341
• /
• 2012

With the advantages of large span, light deadweight and convenient construction, the steel-concrete composite beam (SCCB) has been rapidly developed as a medium span bridge. Compared with common beams, the global stiffness of SCCB is discontinuous and in a staged distribution. In this paper, the analysis model for the simply-supported SCCB is established and the vibration equations are derived. The natural vibration characteristics of a simply-supported SCCB are analyzed, and are compared with the theoretical and experimental results. A curvature mode measurement method is proposed to identify the shear connector damage of SCCB, with the stiffness reduction factor to describe the variation of shear connection stiffness. By analysis on the $1^{st}$ to $3^{rd}$ vertical modes, the distribution of shear connectors between the steel girder and the concrete slab are well identified, and the damage locations and failure degrees are detected. The results show that the curvature modes can be used for identification of the damage location.

• Structural Engineering and Mechanics
• /
• v.66 no.4
• /
• pp.453-463
• /
• 2018

Three points bending flexural test was modelled numerically to study the crack propagation in the pre-cracked beams. The pre-existing double internal cracks inside the beam models were considered to investigate the crack propagation and coalescence paths within the modelled samples. Notch configuration effects on the failure stress were considered too. This numerical analysis shown that the propagation of wing cracks emanating from the tips of the pre-existing internal cracks caused the final breaking of beams specimens. It was also shown that when two notches were overlapped, they both mobilized in the failure process and the failure stress was decreased when the notches were located in centre line. However, the failure stress was increased by increasing the bridge area angle. Finally, it was shown that in all cases, there were good agreements between the discrete element method results and, the other numerical and experimental results. In this research, it is tried to improve the understanding of the crack propagation and crack coalescence phenomena in brittle materials which is of paramount importance in the stability analyses of rock and concrete structures, such as the underground openings, rock slopes and tunnel construction.

• Korean Journal of Mathematics
• /
• v.19 no.3
• /
• pp.331-342
• /
• 2011

We consider the multiplicity of the solutions for a class of a system of critical growth beam equations with periodic condition on t and Dirichlet boundary condition $$\{u_{tt}+u_{xxxx}=av+\frac{2{\alpha}}{{\alpha}+{\beta}}u_{+}^{{\alpha}-1}v_{+}^{\beta}+s{\phi}_{00}\;\;in\;(-\frac{\pi}{2},\;\frac{\pi}{2}){\times}R,\\u_{tt}+v_{xxxx}=bu+\frac{2{\alpha}}{{\alpha}+{\beta}}u_{+}^{\alpha}v_{+}^{{\beta}-1}+t{\phi}_{00}\;\;in\;(-\frac{\pi}{2},\;\frac{\pi}{2}){\times}R,$$ where ${\alpha}$, ${\beta}$ > 1 are real constants, $u_+=max\{u,0\}$, ${\phi}_{00}$ is the eigenfunction corresponding to the positive eigenvalue ${\lambda}_00=1$ of the eigenvalue problem $u_{tt}+u_{xxxx}={\lambda}_{mn}u$. We show that the system has a positive solution under suitable conditions on the matrix $A=\(\array{0&a\\b&0}\)$, s > 0, t > 0, and next show that the system has another solution for the same conditions on A by the linking arguments.

• Journal of the Korea Society for Simulation
• /
• v.15 no.3
• /
• pp.61-67
• /
• 2006

This paper provides a systematic way of integrating human intelligence and autonomous precision of robots to achieve the highest possible performance of a cooperating robot system. Adjustable autonomy, which deals with the combination of human and robotic skills, has the potential to bridge the gap which leaves many tasks suited to robotics beyond the reach of existing technology. Especially we will show that relevant human assistance or intervention will increase system performance by improving the exception handling capability, simplifying autonomous operation, and boosting speed and reliability. To support the usefulness of our scheme, a series of experiments were conducted with three cooperating robots which work together to dock both ends of a long suspended beam into stanchions.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.585-588
• /
• 2007

This study attempts to analyze estimating process and the level of information performing literature review and questionnaire and identify phased influence factors on construction cost using phased information of project and suggests framework of approximate estimation model at the planning and design stage. This paper suggests phased influence factors on construction cost and framework of approximate estimation model for integrated project cost management.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.6 s.67
• /
• pp.603-610
• /
• 2003

A damage identification technique using static displacement data is developed to asses s the structural integrity of bridge structures.As such, the relationship between static displacement and stiffness is derived, and the optimization technique utilized.Comparisons with numerical and experimental tests are performed to investigate the practical applicability of the proposed method.Various damage scenarios are considered by varying damage-width as well as damage-degree. The influence of noise in identifying the damage is also numerically investigated.Finally, the applicability and limitation of the proposed method are discussed.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.730-731
• /
• 2015

This study aims at giving the framework to estimate the environmental load at planning and schematic phase. With increasing awareness of environmental issues, the effort to reduce the environmental impacts caused by human activity has been increasingly enlarged. So far most of researches estimating CO₂ emissions have analyzed energy consumption based on BOQ (Bills of Quantity) acquired after detailed design. There is also lack of reliability in the estimated environmental impact using the basic unit of a facility at the planning stage, because it uses a limited specific section of historical data. Thus, this study is targeted at developing framework to assess reliable environmental loads based on information available at project early phases by making case-bases from historical design information on PSC Beam Bridge. Historical database is built on the basis of the LCA (Life Cycle Assessment) and in order to set input information for estimating model, the literature about information in an early project phase are reviewed. Using the information available in the planning and schematic design stage, the Framework is presented to estimate the environmental load in an early stage in the project. Developing an environmental load estimation model in accordance with the Framework presented in this study, it is expected that the environmental load in the initial project phase can be estimated more quickly and accurately.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.6
• /
• pp.375-380
• /
• 2022

High-speed railway bridges carry a risk of dynamic response amplification due to resonance caused by train loads, and running safety and riding comfort must therefore be reviewed through dynamic analysis in accordance with design codes. The running safety and ride comfort calculation procedure, however, is time consuming and expensive because dynamic analyses must be performed for every 10 km/h interval up to 110% of the design speed, including the critical speed for each train type. In this paper, a deep-learning-based prediction system that can predict the running safety and ride comfort in advance is proposed. The system does not use dynamic analysis but employs a deep learning algorithm. The proposed system is based on a neural network trained on the dynamic analysis results of each train and speed of the railway bridge and can predict the running safety and ride comfort according to input parameters such as train speed and bridge characteristics. To confirm the performance of the proposed system, running safety and riding comfort are predicted for a single span, straight simple beam bridge. Our results confirm that the deck vertical displacement and deck vertical acceleration for calculating running safety and riding comfort can be predicted with high accuracy.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.3A
• /
• pp.305-313
• /
• 2008

A reliability based calibration of dynamic load allowance (DLA) of highway bridge is performed by numerical dynamic analysis of various types of bridges taking into account of the road surface roughness and bridge-vehicle interaction. A total of 10 simply supported bridges with three girder types in the form of prestressed concrete girder, steel plate girder, and steel box girder is analyzed. The cross sections recommended in "The Standardized Design of Highway Bridge Superstructure" by the Korean Ministry of Construction are used for the prestressed concrete girder bridges and steel plate girder bridges while the box girder bridges are designed by the LRFD method. Ten sets of road surface roughness for each bridge are generated from power spectral density (PSD) function by assuming the roadway as "Average Road". A three dimensionally modeled 5-axle tractor-trailer with its gross weight the same as that of DB-24 design truck is used in the dynamic analysis. For the finite element modeling of superstructure, beam elements for the main girder, shell elements for concrete deck, and rigid links between main girder and concrete deck are used. The statistical mean and coefficient of variation of DLA are obtained from a total of 100 DLA results for 10 different bridges with each having 10 sets of road surface roughness. Applying the DLA statistics obtained, the DLA is finally calibrated in a reliability based LRFD format by using the formula developed in the calibration of OHBDC code.