• Journal of Environmental Health Sciences
• /
• v.18 no.1
• /
• pp.84-94
• /
• 1992

In an attempt to develop the immobilized biocatalysts based on immobilized Saccharomyces cerevisiae, immobilized yeast was investigated with respect to the conditions affected to ethanol productivities. Saccharomyces cerevisiae was immobilized in the form of the beads by magnetic-calcium alginate, non magnetic-calcium alginate and acrylamide polymerization. Magnetic immobilized yeast, nonmagnetic immobilized yeast and polyacrylamide immobilized yeast were compared in respect of their pH stability, thermostability, heat tolerance, the relation between the concetration of native yeast and retained activity of immobilized yeast, the activity depending on bead size of immobilized yeast, and the effects of magnesium and cobalt on the activities. The more small bead had retained the higher activity for the three kinds of immobilized yeast. In case of 1.0mm diameter of beads, the retained activity was 40~50% for the all groups. The pH stability profile for the immobilized yeast showed a broad range of optimun activity while the native yeast gave a sharp pick for its optimun pH value. The thermostability was at the range of 25~55$^{\circ}$C for the immobilized yeast groups. It was investigated that the influent magnesium and cobalt concentration, and the relative activity have an influent on heat tolerance at steady state. Both protein content released from immobilized yeast and activity of immobilized yeast were changed after activation of immobilized yeast cell.

• Journal of Welding and Joining
• /
• v.30 no.4
• /
• pp.24-30
• /
• 2012

Laser welding by fiber laser accompanied by a lot of spatter and humping bead. This is because the deep and narrow keyhole usually form due to high beam quality. So the weld bead is formed defects, because the plasma jet with a high vapor pressure make the molten pool on keyhole wall scattered. For such a reason, unstable behavior of keyhole is difficult to monitor laser welding by using the laser induced plasma. Mostly, fiber laser welding of thick plates most be influenced by this effect. Therefore, fiber laser welding has been difficult to apply the sole. Thus, laser welding monitoring based on plasma measurements have much difficulty in measurements and analysis of signal. In this study, influence of the plasma emission signal according to welding speed and laser power in fiber laser welding analysed by using RMS and FFT analysis. We can verify that RMS value of the plasma emission signal changes with welding parameters in fiber laser welding, and aspect ratio greater than 1, the peak of FFT frequency had been moved in accordance with welding parameter.

• Journal of Institute of Convergence Technology
• /
• v.12 no.1
• /
• pp.13-18
• /
• 2022

Polyacrylonitrile was synthesized through suspension polymerization and then sieved to obtain spherical beads with a size of 200~510 ㎛. PAN was copolymerized with 2 mol% MMA monomer which is known to promote cyclization and crosslinking of nitrile group. The resonance cyclization reaction of the nitrile group in the synthesized PAN beads was observed near 170℃ with thermal analysis and FT-IR. The reaction conversion of the nitrile group in spherical beads was 23% during heat treatment, which was lower than that of the well-oriented PAN fiber used as a precursor of carbon fiber. This is because the stereo-regularity of molecular chains in the form of a random coil (spherical bead) is much lower than that of PAN fiber. It was confirmed that the compressive strength of the spherical PAN bead was greatly improved through the resonance cyclization and shrinkage according to the heat treatment, and it was also observed that the pores in PAN beads were formed after the heat treatment.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.245-251
• /
• 2002

We prepared γ-alumina beads using the amorphous alumina, obtained by fast calcination of gibbsite, and its were immersed in aqueous solution of the mixture of 21.87% nitric acid and 28.57% acetic acid. The beads thus were hydrothermaly treated at 200$^{\circ}$C for 3h, and were investigated changes of crystal, pore characteristics, $N_2$ adsorption and desorption isotherms, mechanical strengths and thermal resistance. Acicular platelet crystals of 0.1∼0.3${\mu}$m were transformed into acicular boehmite crystals of 1∼2${\mu}$m having the same crystal structure. Through this changes, we found that reversible phase transformation due to hydrothermal reaction took placed between boehmite and ${\gamma}$-alumina. In comparison to the ${\gamma}$-alumina bead before hydrothermal treatment, $N_2$ adsorption capacity was increased from 450㎖/g to 670㎖/g, and pore volume between 100${\AA}$ and 1000${\AA}$ was increased form 0.15㎖/g to 0.77㎖g, and mechanical strength was increased form 1.4MPa to 2.2MPa. Also, it showed the remarkable thermal resistance which sustained ${\theta}$-alumina crystal structure and pores between 100${\AA}$ and 1000${\AA}$ at 1000$^{\circ}$C in 40vol% steam.

• The Korean Journal of Nuclear Medicine
• /
• v.36 no.2
• /
• pp.133-139
• /
• 2002

Purpose: Scintillation Proximity Assay (SPA) does not require the physical separation of receptor bound form from free form. SPA was applied to the study of interaction of human chorionic gonadotropin (hCG) and $anti-{\alpha}$ hCG in serum. Materials and methods: $Anti-{\alpha}$ hCG was biotinylated for the binding to streptavidin. The assay was based on the simple competitive binding method between $[^{125}I]hCG$ and the hCG in sample serum, with $anti-{\alpha}$ hCG-coated beads. Aliquots of biotinylated $anti-{\alpha}$ hCG were dispensed into scintillation vials containing $100{\mu}{\ell}\;[^125}I]hCG\;and\;200{\mu}{\ell}$ of either a standard concentration of hCG for preparation of standard curve or unknown sample, and incubated for 20 min. at room temperature. Then $20{\mu}{\ell}$ streptavidin-coated beads were added to vials, and finally incubated for 10 min at room temperature. Values for unknown samples were then calculated from the standard curve. Results: Optimal background counts were certificated using varied radioactivity of radionuclides. Appropriate standard curve was obtained from SPA method successively, and the concentration of hCG from unknown serum was determined by standard curve. The result from SPA assay was similar to that of RIA. Conclusion: This observation confirms that SPA method could be useful for clinical diagnosis.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.36-40
• /
• 2018

We have developed a nonlithographic patterning technique using polystyrene nanoparticles to form nanonet channel structures which is promising for high-performance TFT applications. Nanoparticles assisted patterning (NAP) is a technique to form uniform nano-patterns by applying lift-off and dry etch process. Oxygen plasma treatment was used to control the diameters of nanonet hole size to realize a branch width down to 100 nm. NAP technology can be very promising to fabricate nanonet structure with advantages of lower manufacturing cost and large-area patterning capability.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.8 s.145
• /
• pp.1079-1091
• /
• 2005

The purpose of this study was to point out the unification of the size of swimming headgear by measuring detailed measurement of head ferm and systematizes the head form. A total of 300 male and female Korean adults aged from 18 years old to 35 years old were measured through the direct measurement method. This study attempted to identify the head form of male and female adults using measurement data and the head form was classified through factor analysis and cluster analysis. (1) Based on the fact that this study especially focuses on the size of swimming headgear, factor analysis was performed far both direct measurements with hair and without hair. For the measurements with hair, seven factors were extracted. They were head thickness factor, head width factor, width of side head factor, height of back head factor, length of front head factor, circumference of front head factor, thickness of front head factor and head height factor. They explained the $70.95\%$ of the measurements. (2) The cluster analysis was executed to classify the somatotype of the korean head form on the basis of similarity. According to the cluster analysis result, the measurements with hair categorized types, 'Woman's long-hair type', 'Small type', 'Long and flat type', 'Large type'. (3) Head circumference B and Left tragion - Vertex - Right tragion circumference which are generally length and width in choosing swimming headgear size were selected as measurement items far size of swimming headgear. Direct measurements and sizes of four swimming headgear with different materials taking into account their elongation rate were also compared.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.2
• /
• pp.216-227
• /
• 2007

Statement of problem: For the long-term success of removable partial dentures, the bonding between metal framework and denture base resin is one of the important factors. To improve bonding between those, macro-mechanical retentive form that is included metal framework design has been generally used. However it has been known that sealing at the interface between metal framework and denture base resin is very weak, because this method uses mechanical bonding. Purpose: Many studies has been made to find a simple method which induces chemical bond, now various bonding system is applied to clinic. In this experiment, shear bond strengths of heat-cured denture base resin to the surface-treated Co-Cr alloy were measured before and after thermocycling. Chemically treated groups with Alloy $Primer^{TM}$, Super-Bond $C&B^{TM}$, and tribochemically treated group with $Rocatec^{TM}$ system were compared to the beadtreated control group. The data were analyzed with two-way ANOVA. Result: 1. Shear bond strength of bead-treated group is highest, and Alloy $Primer^{TM}$ treated group, Super-Bond $C&B^{TM}$ treated group, RocatecTM system treated group were followed. Statistically significant differences were found in each treated group(p<0.05). 2. Surface treatment and thermocycling affected shear bond strength(p<0.05), however there was no interaction between two factors(p>0.05). 3. Shear bond strengths of bead-treated group and Alloy $Primer^{TM}$ treated group showed no statistically significant difference before and after thermocycling(p>0.05), and those of Super-Bond $C&B^{TM}$ treated group and $Rocatec^{TM}$ system treated group showed statistically significant difference after thermocycling(p<0.05).

• Journal of Korea Foundry Society
• /
• v.29 no.6
• /
• pp.270-276
• /
• 2009

After casting button-type small ingots of ternary Fe-Mn-S alloys which had three different Mn/S ratios (1, 5 and 70) in a vacuum arc furnace, the effect of the ratio on the sulfide formation was investigated. In case of the Mn/S ratio of 1, if alloy composition was located in an iron-rich corner on a Fe-Mn-S ternary phase diagram, only duplex MnS-FeS sulfide films were observed in the grain boundary. If the alloy composition was located in the miscibility gap area of the phase diagram, primary globular dendritic sulfides and dendritic sulfide slags were generated within the grain and tubular monotectic sulfides were also detected in the grain boundary. When the Mn/S ratio was 5, if the alloy composition was in the iron-rich corner, only bead-like sulfides were generated. On the other hand, if the composition was in the miscibility gap area, globular dendritic sulfides and dendritic sulfide slags were generated in the form of primary sulfide inclusions and rod-like eutectic sulfides were observed in the grain boundary. Especially, if the contents of Mn and S increased more in the miscibility gap area of the phase diagram, primary globular sulfides containing iron intrusions were observed. In case of Mn/S ratio of 70, if the contents of Mn and S was decreased in the Fe corner of the phase diagram, only bead-like sulfides were observed in the grain boundary. Despite the composition was outside the miscibility gap area of the phase diagram, if the contents of Mn and S increased, clusters of fine sulfide particles as well as fine spherical primary monophase sulfides were observed in the grain boundary.

• Korean Journal of Microbiology
• /
• v.27 no.1
• /
• pp.48-55
• /
• 1989

The purpose of the present investigation was to improve several procedures being used in the adherence assay of Streptococcus sanguis cells to hydroxyapatite (HA) beads and to study the effect of the beads on the counting of radioactivity. The standard adhere assay involved the adherence of radiolabeled bacteria to 40mg of HA beads. The beads were mixed with ['H]thymidine-labeled bacterial cells and incubated for 60 minutes at room temperature. Unadsorbed cells were removed, the beads with adsorbed cells were dried, and the radioactivity was monitered in a scintillation spectrometer. The 30 seconds sonication of cells in a form of long chains appeared to be adequate for obtaining mostly singlet or doublet cells. Unlike the counting of S. sanguis cell suspension, bacterial cells adhered to HA or saliva-coated HA(SHA) required smaller volume (2.5ml) of scintillaton fluid for better counting. Eighteen percent quenching of counts could be attributed to the beads. Among 3 procedures commonly used to equilibrate the beads for adherence assay, no differences were found in their effectiveness. The HA beads on which the bacteria remained attached in scintillant during the counting were found to be the source of sample self-absorption representing 34.5% of the total radioactivity counts resulting from the beads dissolved in HCl solution.