• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.8B
• /
• pp.1012-1020
• /
• 2011

In this paper a design of $\pi$/4-DQPSK baseband receiver for the exchange of digital data and e-mail between shore and ship stations and/or among ship stations in the maritime mobile service VHF channels is described. Due to the permitted relatively big frequency instability of local oscillators at the transmitter and the receiver of maritime communication system, the designed baseband receiver should have the capabilities of correct estimation and compensation of the synchronization parameters, such as symbol timing and frequency offset, from the received signal which might include relatively big frequency error. Simulated BER results show that the designed baseband receiver works less than 0.5dB loss under AWGN channel when the normalized frequency offset of the received signal is more then 20%.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.12
• /
• pp.1903-1909
• /
• 1989

In this paper, the mobile communication CH simulator is implemented in the baseband, using the Digital Signal Processor(TMS320C25), A/D and D/A converters. The Rayleigh CH is modeled by shaping the random noise source power spectrum. The statistical characteristics(Level Crossing Rate, Cumulative distribution Function, Probability Density Function) and the received fading signal's power's spectrum is observed when the doppler frequency is varied according to the variation of the vehicular velocity at the 222MHz band. And also the BER is measured when the baseband mobile CH simulator is applied to the GMSK(Gaussian Minimum Shift Keying` transmission rate: 16kbps, Bb T=0.25) modulator. The results shows the similar characteristics to be compared with the theoritically derived BER values of the discriminator type GMSK detection.

• ETRI Journal
• /
• v.25 no.5
• /
• pp.328-336
• /
• 2003

Bluetooth is a specification for short-range wireless communication using the 2.4 GHz ISM band. It emphasizes low complexity, low power, and low cost. This paper describes an area-efficient digital baseband module for wireless technology. For area-efficiency, we carefully consider hardware and software partitioning. We implement complex control tasks of the Bluetooth baseband layer protocols in software running on an embedded microcontroller. Hardware-efficient functions, such as low-level bitstream link control; host controller interfaces (HCIs), such as universal asynchronous receiver transmitter (UART) and universal serial bus (USB)interfaces; and audio Codec are performed by dedicated hardware blocks. Furthermore, we eliminate FIFOs for data buffering between hardware functional units. The design is done using fully synthesizable Verilog HDL to enhance the portability between process technologies so that our module can be easily integrated as an intellectual property core no system-on-a-chip (SoC) ASICs. A field programmable gate array (FPGA) prototype of this module was tested for functional verification and realtime operation of file and bitstream transfers between PCs. The module was fabricated in a $0.25-{\mu}m$ CMOS technology, the core size of which was only 2.79 $mm{\times}2.80mm$.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.16 no.1
• /
• pp.93-98
• /
• 2020

Research on underwater sensor networks is increasing due to such reasons as marine resource management, maritime disaster prediction and military protection. Many underwater sensor networks performs wireless communication using an acoustic sound wave band signal having a relatively low frequency. So the digital part of their modem can take charge of carrier band signal processing. To enable this, the sampling rate of the baseband band signal should be increased to a sampling rate at which carrier band signal processing is possible. In this paper, we designed a sampling rate increasing circuit based on a CIC interpolator for underwater sensor nodes. The CIC interpolator has a simple circuit structure. However, since the CIC interpolator has a large attenuation of the pass band and a wide transition band, an inverse sinc LPF is added to compensate for frequency response of the CIC interpolator. The proposed interpolator was verified in time domain and frequency domain using ModelSim and Matlab.

• The Journal of the Acoustical Society of Korea
• /
• v.9 no.2
• /
• pp.61-69
• /
• 1990

We have investigated the digital bit synchronization problem in baseband communication receiver systems using the Gauss-Markov estimation technique which is equivalent to the weighted least square method. The realized bit synchronizer, including the data detector, processes the input signal two dimensionally into the transition phase and data level under the white Gaussian noise environment. We have confirmed the relization of the bit synchronizer via computer simulation. In addition, we have compared and evaluated the estimation error performance of the proposed method with that of the conventional DTTL method and of the minimum likelihood method.

• Journal of Advanced Navigation Technology
• /
• v.18 no.6
• /
• pp.541-545
• /
• 2014

Rec. ITU-R M.1842-1 is international recommendation for VHF band communication guideline in maritime mobile service RR Appendix 18 channels. In this paper, we simulate 28.8 kbps VHF ${\pi}$/4-DQPSK digital baseband modem compatible with the recommendation, then it is designed and implemented with FPGA. Cazac sequence is used as a preamble since packet format is not defined untill now in the recommendation. Baseband modem is designed by VHDL language and implemented on NEXYS4 development platform having Atrix7 FPGA chip from Xilinx. For wireless communication test of total prototype system, ADC/DAC board is implemented and EV9730 RF module is utilized. From the experimental results, implemented FPGA modem shows spectral bandwidth of 25 kHz and successful data exchanges between tx and rx communication platform.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.336-342
• /
• 2017

Recently, there has been an increasing need for underwater communication systems to monitor ocean environments and prevent marine disasters, as well as to secure ocean resources. Most underwater communication systems adopted acoustic communication with a consideration of attenuation, absorption, and scattering in conductive sea water, and developed fully digital modems based on processors. In this study, a digital up converter (DUC) and a digital down converter (DDC) was developed for an underwater basestation based on underwater acoustic communication systems. Because one of the most important issues in underwater acoustic communication systems is low power consumption due to environmental problems, this study developed a specific hardware module for DUC and DDC. It supported four links of underwater acoustic communication systems and converted the sampling rate and frequency. The systemwas designed and verified using Verilog-HDL in ModelSim environment with the test data generated from baseband layer parts for an underwater base station.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.12
• /
• pp.1044-1052
• /
• 1990

We have investigated the digital bit synchronization problem in baseband communication receiver systems using the Gauss-Markov estimation technique which is equivalent to the weighted least square method. The realized bit synchronizer, including the data detector, processes the input signal two dimensionally into the transition phase and data level under the white Gaussian noise environment. We have confrmed the realiation of the bit synchronizer via computer simulation. In addition, we have compared and evaluated the estimation error performance of the proposed method with that of the conventional DTTL method and of the minimum likelihood method.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.1-14
• /
• 1998

In this paper, Antenna, LNA, Mixer, VCO, and Modulation/Demodulation in Baseband processor which are the RF main components in Wireless LAN system for ultra high-speed communications network are studied. Antenna bandwidth and selective fading due to multipath can be major obstacles in high speed digital communications. To solve this problem, wide band MSA which has loop-structure magnetic antenna characteristics is designed. Distributed mixer using dual-gate GaAs MESFET can achieve over 10dB LO/RF isolation without hybrid, and minimize circuit size. As linear mixing signal is produced, distortions can be decreased at baseband signals. Conversion gain is achieved by mixing and amplification simultaneously. Mixer is designed to have wide band characteristics using distributed amplifier. In VCO design, Oscillator design method by large signal analysis is used to produce stable signal. Modulation/Demodulation system in baseband processor, DS/SS technique which is robust against noise and interference is used to eliminate the effect of multipath propagation. DQPSK modulation technique with M-sequences for wideband PN spreading signals is adopted because of BER characteristic and high speed digital signal transmission.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.1E
• /
• pp.18-24
• /
• 2002

This paper discusses the development of an acoustic vector channel simulator for the performance analysis of an acoustic digital communication system. The channel simulator consists of transmission module, acoustic channel model, receiver, beamformer, and adaptive equalizer. The source signal (QPSK) is generated by the specified parameters. The transmitted signal generates multipath signals which have a different delay, amplitude and doppler frequency. The paper presents in details the approach to the performance analysis of an acoustic digital communication system according to the antenna structure and the various baseband signal processing techniques.