• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.20-23
• /
• 2001

Plasma Display Panel(PDP) is a type of flat panel display utilizing the light emission produced by gas discharge. Barrier Ribs of PDP separating each sub-pixel prevents optical and electrical crosstalks from adjacent sub-pixels. The mold for forming the barrier ribs has been newly researched to overcome the disadvantages of conventional manufacturing processes such as screen printing, sand-blasting and photosensitive glass methods. The mold for PDP barrier ribs have stripes of micro grooves transferring glass-material wall. In this paper, Stripes of grooves of which width 48${\mu}{\textrm}{m}$, depth 124$\mu\textrm{m}$ , pitch 274$\mu\textrm{m}$ was acquired by machining of single crystal silicon with dicing saw blade. Maximum roughness of the bottom of the grooves was 59.6nm Ra in grooving Si. Barrier ribs were formed with silicone rubber mold, which is transferred from grooved Si forming hard mold. Silicone rubber mold has the elasticity, which enable to accommodate the waveness of lower glass plate of PDP. The methods assisted by the microwave and UV was adopted for reducing the forming time of glass paste.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.771-774
• /
• 2003

The mechanical properties of barrier ribs in PDP require quantification in order to control the defects and to increase the yield in the process. Several different types of rib materials were tested for hardness (H) and Young's modulus (E) with a microtip indenter (Berkovich type). For the assessment of fracture toughness of the rib, a macro Vikers indenter was used. The materials with 30wt% of filler were fired at between $490^{\circ}C$ and $570^{\circ}C$. As a result, the composite became fully densified at $520^{\circ}C$, which is near the T s (Littleton softening point) of glass frit. As the filler content increased, the fracture toughness also $(K_{IC})$ increased in the range of 0.60 to 2.63 $MPa{\cdot}m^{0.5}$ after sintering at $550^{\circ}C$. The results suggest that the application of a nano-indenter would be useful for testing the mechanical properties of barrier ribs.

• Journal of Information Display
• /
• v.5 no.3
• /
• pp.25-29
• /
• 2004

Effects of additing various types of ceramic fillers to the BZB-based glass on the thermo-chemical stability, optical reflectance, and mechanical properties were investigated. The glass system demonstrated the feasibility to host various types of ceramic fillers to form micro-composites at the processing temperature suitable for PDP systems. The optical reflectance and mechanical strength of the filler-glass composites were improved as compared to the glass itself. These results demonstrate the feasibility of applying the Pb-free BZB-based glass system as a matrix for employing various types of crystalline ceramic fillers to be used as barrier rib materials in plasma display panels.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.1
• /
• pp.31-38
• /
• 2002

We measured a 3-dimensional images of the light emitted from plasma display panel(PDP) by using newly proposed scanned point detecting system. In the panel without phosphor, as we scan from the rear glass to the front glass, the detected light intensity increases and the light intensity detected in the inside edge of the ITO electrodes shows the stronger intensity than others. The light intensity detected between the barrier ribs shows the largest value of brightness. Also, as the sustain voltage increases, the detected light intensity increases. In the panel with phosphor, the intensity of light detected at barrier rib shows the stronger light intensity than rear plate. Therefore, the phosphor of barrier rib is very important. From these results the 3-dimensional measurement is necessary to understand exactly the discharge phenomenon in the PDP cell.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.784-787
• /
• 2003

In this study, water jet etching of aqueous green tape was attempted for processing barrier rib of plasma display panel. This process combines 1) chemical etching between water and aqueous based binder in the tape and 2) mechanical erosion by water jet. Effects of etching parameters such as pressure, temperature and aqueous binder content on the morphology of barrier ribs formed were investigated. The results demonstrated a possibility of processing barrier ribs by water jet etching.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.57-62
• /
• 2000

In this study, an attempt was made to demonstrate the possibility of using laser scribing method in manufacturing the barrier ribs of plasma display panel. The scribing with a CO2 laser was conducted on the green tape produced by the doctor blade tape casting method. Among the processing parameters, the quenching gas pressure, shape of mask, and laser power were found to affect the depth and angle of the scibed barrier ribs.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.189-190
• /
• 2008

• Proceedings of the Korean Printing Society Conference
• /
• 2001.06a
• /
• pp.104-110
• /
• 2001

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.727-730
• /
• 2004

Closed-cell type barrier ribs such as honeycomb, SDR, inverse SDR and waffle types were produced using capillary molding process. Phosphor layers were formed by osmosis coating process on those barrier ribs. Using the rear plate with closed-cell ribs, the luminance and its efficiency was measured. The results demonstrated a significant improvement in efficiency by combining closed-cell type ribs with a new phosphor forming technology

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.867_868
• /
• 2009

Interior permanent magnet synchronous motor [IPMSM] which has high power density is applied to motor for Hybrid electric vehicle[HEV], Electric vehicle[EV], Fuel cell electric vehicle[FCEV] and electric home appliances. In order to improve efficiency performance of IPMSM, this paper presented a study by making a hole around air barrier. Because concentrated rib stress is distributed by suitable hole, the hole can reduce rib thickness of IPM rotor. And it can help decrease PM[Permanent Magnet] leakage flux. Saliency ratio($L_q/L_d$) is also increased by magnetic circuit change. For this study, structure analysis of rotor is performed by Ansys program.