• Journal of the Korean Vacuum Society
• /
• v.16 no.5
• /
• pp.330-337
• /
• 2007

Influence of glass dielectric property (dielectric constant K, dielectric loss) on the external electrode fluorescent lamps of the dielectric barrier discharge has been investigated with 4-different glasses. Conventional borosilicate glass tubes with $K=5.6{\sim}5.9$ and tan ${\delta}=5.0{\times}10^{-3}{\sim}6.0{\times}10^{-3}$ and aluminosilicate glass tubes with high K=6.6 and low tan ${\delta}=1{\times}10^{-4}$ and soda-lime glass tribes with K=7.7 and tan ${\delta}=1.37{\times}10^{-2}$ have been compared. The high value of dielectric constant K makes the capacitance of external electrode fluorescent lamps intensity and enhances the discharge efficiency. The dielectric loss of tan ${\delta}$ shows the factor of power consumption in the external electrode to induce heats and to be weak in pinhole stability. The aluminosilicate glass tubes of high K and low tan ${\delta}$ have been enhanced by $14{\sim}18%$ in luminance and efficiency in comparison with the conventional borosilicate glass tubes and the aluminosilicate external electrode fluorescent lamps are strong against the pinhole formation. Soda-lime glass tubes with high K and high tan ${\delta}$ are a little favorable in luminance and efficiency and they are very weak in pinhole occurrence.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.2_spc
• /
• pp.305-315
• /
• 2020

For geological disposal of radioactive wastes, a method was proposed to evaluate the radionuclide transport in the biosphere by calculating the elapsed time of nuclide migration. The radionuclides were supposed to be introduced from a natural barrier and reached a large surface water body following a groundwater flow in a shallow subsurface. The biosphere was defined as a shallow subsurface environment that included aquifers on a host rock. Using the proposed method, a calculation algorithm was established, and a computer code that implemented the algorithm was developed. The developed code was verified by comparing the simulation results of the simple cases with the results of the analytical solution and a public program, which has been widely used to evaluate the radiation dose using the radionuclide transport near the surface. A case study was constructed using the previous research for radionuclide transport from the hypothetical geological disposal repository. In the case study, the code calculated the mass discharge rate of radionuclide to a stream in the biosphere. Because the previous research only demonstrated the transport of radionuclides from the hypothetical repository to the host rock, the developed code in the present study could help identify the total transport of radionuclide along the complete pathway.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.6
• /
• pp.444-452
• /
• 2009

Textural parameters were calculated from the surface sediments collected from Jinu-do beach in Nov. 2005 and May 2006. In Nov. 2005 and May, 2006, the grain size distribution of surface sediments shows that the mode of $3.0\phi$(i.e., 0.125 mm) dominated the west beach of Jinu-do, but in the east beach the mode of $3.0\phi$(i.e., 0.125 mm) decreased and the mode of $2.5\phi$(i.e., 0.177 mm) was apparently distinct, resulting in the more coarsening trend. Mean grain size of surface sediments also indicates little difference in the west beach between two investigations, but the increasing difference between mean grain sizes in the east beach, showing more coarsening pattern. Such seasonal pattern corresponds to the positive skewness in the east beach in May, 2006. As a result, after the winter in 2005, the surface sediments in the west beach of Jinu-do experienced a little variation, whereas the apparent coarsening of surface sediments occurred in the east beach by removal of $3.0\phi$(i.e., 0.125 mm) fine-grained sand particles. The observed seasonal change may be attributed to the different hydrographic condition and sediment delivery/removal on the surface sediments between the west beach and the east beach of Jinu-do through the increased precipitation and more freshwater discharge from the Nakdong River during the summer and the intensified wave and tide during the winter in the Nakdong River estuary.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.38.2-38.2
• /
• 2011

폴리머 박막은 그 고유한 특성으로 인해 여러 산업적으로 널리 사용되고 있는 재료이다 예로 의약품이나 식품 포장지의 배리어, 전자부품의 절연체, 반도체 공정에서의 사용, 혹은 부식방지를 위해 사용 되어지기도 한다. 이 폴리머 박막을 증착 하기 위한 방법으로 이전부터 CVD (Chemical Vapor Deposition) 방법이 많이 사용되었고 지금까지도 가장 많이 사용되는 방법이다. CVD를 사용하여 $SiO_2$-like 필름의 증착은 전구체(precursor)로 Silane ($SiH_4$)을 사용하였으며, 플라즈마 발생 소스(source)로 열 혹은 전기장 등을 사용 하며 공정 시 압력 또한 대부분 저압 하에서 실시 하였다. 이와 같은 이전 CVD 방법의 문제는 사용되는 Silane 자체가 인체에 해로울 정도로 독성이 있으며 폭발성도 같이 가지고 있어 작업환경의 위험성이 높으며 열을 사용한 CVD의 경우 높은 공정 온도로 인해 증착 할 수 있는 대상이 제한 되어 지며 높은 열의 발생을 위해 많은 에너지의 소비가 필요하다. 저압 플라즈마를 사용한 CVD 는 공정상 높은 열의 발생이 일어나지 않아 기판 운용상 문제가 되지 않지만 저압 환경에서 해당 공정이 이루어기 때문에 인해 필수적으로 고가의 진공 챔버가 필수적이며 저압을 유지할 고가의 진공 펌프나 추가 장비들이 필요하게 된다, 또한 챔버 내에서 이루어지는 공정으로 인해 공정의 연속성이 떨어져 시잔비용 또한 많이 잡아 먹는다. 이러한 열 혹은 저압 플라즈마등을 사용한 공정의 단점을 해결하기 위해 여러 연구자들이 다양한 방법을 통해 연구를 하였다. 대기압 유전체 배리어 방전(AP-DBD: Atmospheric Pressure-Dielectric Barrier Discharge)을 사용한 폴리머 박막의 증착은 이전 전통적인 방법에 비해 낮은 장비 가격과 낮은 공정 온도 그리고 연속적인 공정 등의 장점이 있는 폴리머 박막 증착 방법 이다. 대기압 유전체 배리어 방전 공정 변수로 공급 전압 및 주파수 그리고 공급 전압의 영향, 전구체를 유전체 배리어 방전 전극으로 이동 시키기 위해 사용된 캐리어 가스의 종류 및 유량, 화학양론적 계수를 맞추기 위해 같이 포함되는 산소 가스의 유량, DBD 전극의 형태에 따른 증착 박막의 균일성 등 이 존재하며 이런 많은 변수 들에 대한 연구가 진행 되었지만 아직 이 대기압 DBD를 이용한 폴리머 박막의 증착에 대한 명확한 이해는 아직 완전 하다 할 수 없다. 본 연구에서는 이러한 대기압 DBD를 이용하여 폴리머 박막의 증착시 영향을 미치는 많은 공정 변수 등이 박막생성에 미치는 영향과 증착된 박막의 성질에 대한 연구를 진행 하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.4
• /
• pp.374-382
• /
• 2009

Steam generator(SG) tube, as a barrier isolating primary to the secondary coolant system of nuclear power plants(NPP), must maintain the structural integrity far the public safety and its efficient power generation capacity. And SG tubes bearing defects must be timely detected and taken repair measures if needed. For the accomplishment of these objectives, SG tubes have been periodically examined by eddy current testing(ECT) on the basis of administrative notices and intensified SG management program(SGMP). Stress corrosion cracking(SCC) on the SG tubes is not easily detected and even missed since it has lower signal amplitude and other disturbing factors against its detection. However once SCC is developed, that can cause detrimental affects to the SG tubes due to its rapid propagation rate. Accordingly SCC is categorized as prime damage mechanism challenging the soundness of the SG tubes. In this study, reproduced EDM notch specimens are examined for the detectability and quantitative characterization of the axial ODSCC by +PT MRPC probe, containing pancake, +PT and shielded pancake coils apart in a single plane around the circumference. The results of this study are assumed to be applicable fur providing key information of engineering evaluation of SCC and improvement of confidence level of ECT on SG tubes.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.4
• /
• pp.405-418
• /
• 2019

Based on spent fuels characteristics from domestic nuclear power plants and a disposal scenario from the current basic plan for high-level radioactive waste management, an improved disposal system has been proposed that enhances disposal efficiency and economic effectiveness compared to the existing disposal system. For this purpose, two disposal canisters concepts were derived from the length of the spent fuel generated from the nuclear power plants. In the disposal scenario, the acceptable amount of decay heat for each disposal container was determined, taking into account the discharge and disposal times of spent fuels in accordance with the current basic plan. Based on the determined decay heat of the two types of disposal canisters and the associated disposal system, thermal stability analyses were performed to confirm their suitability to the proposed disposal system design requirement and disposal efficiency assessment. The results of this study confirm 20% reduction in the disposal area and 20% increase in disposal density for the proposed disposal system compared to the existing system. These results can be used to establish a spent fuel management policy and to design a viable commercial disposal system.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.2
• /
• pp.191-196
• /
• 2006

The injection of ozone, produced by dielectric barrier discharge, into the exhaust gas gives rise to a rapid oxidation of NO that is the main component of nitrogen oxides($NO_x$) in most practical exhaust gases. Once NO is converted into $NO_2$, it on readily be reduced to $N_2$ in the next step by a reducing agent such as sodium sulfide and sodium sulfite. The reducing agents used ca also remove $SO_2$ effectively, which makes it possible to treat $NO_x\;and\;SO_2$ simultaneously. The present two-step process made up of an ozonizing chamber and an absorber containing a reducing agent solution was able to remove about 95% of the $NO_x$ and 100% of the $SO_2$, initially contained in the simulated exhaust gas. The formation of $H_2S$ from sodium sulfide was prevented by using a strong basic reagent(NaOH) together with the reducing agent. The removal of $NO_x$\;and\;SO_2$ was more effective for $Na_2S$ than $Na_2SO_3$.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.3
• /
• pp.330-336
• /
• 2005

The ozone injection method was proposed to improve the catalytic process for the removal of nitrogen oxides ($NO_x$). Nitric oxide (NO) in the exhaust gas was first oxidized to nitrogen dioxide ($NO_2$) by ozone produced by dielectric barrier discharge, and then the exhaust gas containing the mixture of NO and $NO_2$ was directed to the catalytic reactor where both NO and $NO_2$ were reduced to $N_2$ in the presence of ammonia as the reducing agent. A commercially available $V_2O_5-WO_3/TiO_2$ catalyst was used as the catalytic reactor. The $NO_2$ content in the mixture of NO and $NO_2$ was changed by the amount of ozone added the exhaust gas. The effect of reaction temperature, initial $NO_x$ concentration, feed gas flow rate, and ammonia concentration on the removal of $NO_x$ at various $NO_2$ contents was examined and discussed. The increase in the content of $NO_2$ by the ozone injection remarkably improved the performance of the catalytic reactor, especially at low temperatures. The present ozone injection method appears to be promising for the improvement of the catalytic reduction of $NO_x$.

• Applied Chemistry for Engineering
• /
• v.24 no.5
• /
• pp.518-524
• /
• 2013

This study investigated the degradation of taste-and-odor compounds and toxins using dielectric barrier discharge plasma. The degradation of taste-and-odor compounds was conducted on geosmin and 2-methyl isoborneol (2-MIB), and the toxins investigated were microcystin-LR (MC-LR), microcystin-RR (MC-RR), microcystin-YR (MC-YR) and anatoxin-a. Largely depending on the type of gas fed to the plasma reactor, the degradation efficiencies of the taste-and-odor compounds decreased in order of oxygen (100%) > dry air (96%) > nitrogen (5%) for geosmin and in order of oxygen (100%) > dry air (94%) > nitrogen (2%) for 2-MIB on the basis of 150 s reaction time. This result suggests that the oxidative reactive species generated during plasma treatment, especially long-lived ozone, are mainly responsible for the degradation of these compounds. When using oxygen as the feed gas, geosmin and 2-MIB were totally degraded within 150 s, microcystins within 10 s, and anatoxin-a within 30 s. It was found that the taste-and-odor compounds and toxins were degraded more rapidly in real lake water than in distilled water.

• Korean Journal of Food Science and Technology
• /
• v.50 no.2
• /
• pp.165-171
• /
• 2018

Atmospheric-pressure plasma (APP) was applied to determine quality characteristics of brown rice (BR) and white rice (WR) of Samkwang and Palbangmi. APP (250 W, 15 kHz, ambient air) was generated and dielectric barrier discharge was applied for 0, 10, and 20 min for 2 weeks at 4 and $25^{\circ}C$. The growth of total aerobic bacteria and mold increased depending on the storage. Water content of BR and WR decreased by storage temperature and periods. No viable counts were detected for molds by APP-treated 20 min at $4^{\circ}C$. Changes in protein and damaged starch contents in plasma were not observed. Amylose contents were not changed, but WR (Palbangmi) showed a tendency to increase. The results show that APP improved the microbial quality of BR and WR of Samkwang and Palbangmi, although further studies should be conducted to determine change in quality by APP.