• 한국전산유체공학회지
• /
• 제14권1호
• /
• pp.70-77
• /
• 2009

In this study, time-dependent numerical analysis was carried out to investigate the plasma jet impingement on a flat plate, and a compressible form of two-dimensional inviscid gas dynamics equations were solved using the flux corrected transport algorithm. The mathematical modeling of Joule heating in the polycarbonate capillary bore and the mass ablation from the bore wall was incorporated in the numerical analysis and the series of computation was performed for three cases depending on the distance of the opposing plate from the capillary exit. The computational results reveal that the presence of the opposing plate does not affect the flow conditions inside the capillary when compared to the case of open-air plasma discharge. In the exterior region, the flow structure shows the typical supersonic underexpanded jet which consists of the strong Mach disk in front of the opposing plate and the barrel shock at the side of the jet. It is found that the shock evolution becomes more quasi-steady when the plate distance decreases. Also, the effects of the distance between the capillary bore exit and the opposing plate on the flow conditions along the opposing plate are investigated and the pressure variation on the plate shows more complicated interaction between the plasma discharge and the opposing plate when the location of plate becomes closer to the capillary exit.

• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1961-1971
• /
• 2006

A soft recovery system (SRS) is a device that stops a high speed projectile without damaging the projectile. The SRS is necessary to verify the shock resistant requirements of microelectronics and electro-optic sensors in smart munitions, where the projectiles experience over 20,000 g acceleration inside the barrel. In this study, a computer code for the performance evaluation of a SRS based on ballistic compression decelerator concept has been developed. It consists of a time accurate compressible one-dimensional Euler code with use of deforming grid and a projectile motion analysis code. The Euler code employs Roe's approximate Riemann solver with a total variation diminishing (TVD) method. A fully implicit dual time stepping method is used to advance the solution in time. In addition, the geometric conservation law (GCL) is applied to predict the solutions accurately on the deforming mesh. The equation of motion for the projectile is solved with the four-stage Runge-Kutta time integration method. A small scale SRS to catch a 20 mm bullet fired at 500 m/s within 1,600 g-limit has been designed with the proposed method.

• 한국식품영양과학회지
• /
• 제30권2호
• /
• pp.292-298
• /
• 2001

This study was conducted to investigate physicochemical properties of extrudates combining 4 levels of squid (0, 3, 5 and 7%) with 3 levels of defatted soy flour (0, 5, and 10%). Blends were adjusted to moisture content of 27% and then extruded in a single-screw laboratory extruder at 170rpm screw speed and 16$0^{\circ}C$ barrel temperature. The extruded materials were dried at 6$0^{\circ}C$ for 8hr to a moisture content of 3~4% and refrigerated at 4$^{\circ}C$ for 12 hour before examination for textural properties, expansion ratio, bulk density, shear force and Hunter color. Expansion ratio of extrudates decreased as squid content increased whereas bulk density and shear force increased. Expansion ratio of extrudates was not significantly different by defatted soyflour level. Bulk density of products decreased as defatted soyflour content increased but shear force of products increased as defatted soyflour content increased. In scores of sensory hedonic evaluation of snacks, appearance, flavor, texture and overall acceptability values had lowered as squid level increased. Therefore, according to materials contents on extrudates increased, nutritional contents of this products increased and also shear force and bulk density in physical properties increased whereas expansion ratio decreased.

• Korea-Australia Rheology Journal
• /
• 제20권4호
• /
• pp.235-243
• /
• 2008

The aim of this study is to explore the possibility of incorporating supercritical carbon dioxide ($scCO_2$) into twin screw extrusion process for the production of polypropylene-clay nanocomposite (PPCN). The $CO_2$ is used as a reversible plasticizer which is expected to rapidly transport polymeric chains into the galleries of clay layers in its supercritical condition inside the extruder barrel and to expand the gallery spacings in its sub-critical state upon emerging from die. The structure and properties of the resulting PPCNs are characterized using wide-angle X-ray diffraction (WAXD), transmission electron microscopy (TEM), rheometry, thermogravimetry and mechanical testing. In the processing of the PPCNs with $scCO_2$, optimum $scCO_2$ concentration and screw speed which maximized the degree of intercalation of clay layers were observed. The WAXD result reveals that the PP/PP-g-MA/clay system treated with $scCO_2$ has more exfoliated structure than that without $scCO_2$ treatment, which is supported by TEM result. $scCO_2$ processing enhanced the thermal stability of PPCN hybrids. From the measurement of linear viscoelastic property, a solid-like behavior at low frequency was observed for the PPCNs with high concentration of PP-g-MA. The use of $scCO_2$ generally increased Young's modulus and tensile strength of PPCN hybrids.

• 한국식품과학회지
• /
• 제27권2호
• /
• pp.164-169
• /
• 1995

퍼지 이론을 적용하여 압출성형공정을 제어하는 모의실험을 수행하였다. 압출물의 두께(팽화율)가 측정변수로 피드백 입력되고 퍼지제어기를 통하여 스크류 회전속도의 set point가 출력되었다. 얻어진 set point로 가상의 압출성형기가 작동하여 또 다른 두께값이 측정값으로 입력되었다. 이와같은 일련의 과정이 반복되면서 최종적으로 원하는 두께값을 얻을 수 있었고 피지제어기의 알고리즘은 압출성형 전문가로부터 얻어진 기본 법칙을 이용하여 작성 하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.106-109
• /
• 2014

In order to obtain dynamic behaviors of complex structures, it demands large amounts computational cost and time to perform the numerical analysis. The model reduction method helps these problems by dividing the full model into primary and unnecessary parts. In this research, we perform the modal analysis using the dynamic substructuring method, which is one of the model reduction methods, in order to obtain the dynamic characteristics of the cylindrical structures efficiently. To select the master degrees of freedom (dofs), we consider the mode shapes of the cylindrical structures. And then, we identify the validity of the dynamic substructuring method by applying the method to the simple cylinder and core support barrel (CSB) which is one of the reactor internals with the cylindrical shape. The results demonstrate that the dynamic characteristics from the dynamic substructuring method are well matched with the original method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.399-401
• /
• 2014

The comprehensive vibration assessment program(CVAP) of APR+ nuclear power plant(NPP) is classified as non-prototype, category II with Palo Verde NPP as valid prototype. In this paper, CVAP for first plant of APR+ NPP is proposed. The Control Element Assembly(CEA) shroud of APR+ NPP is different from that of Palo Verde NPP. And the Core Support Barrel(CSB) outer diameter and the flow rate of normal operation of APR+ NPP are larger than those of Palo Verde NPP. Vibration and stress analysis program should be conducted to establish test acceptance criteria. Limited vibration measurement program should be implemented to establish the margin of safety, demonstrate the satisfaction of test acceptance criteria and confirm the similar vibratory response between the APR+ and Palo Verde NPP. Because of the change of normal operation condition, the nominal differences between APR+ and Palo Verde NPP in the structural and hydraulic analysis are studied to determine the measurement locations.

• Nuclear Engineering and Technology
• /
• 제27권5호
• /
• pp.710-720
• /
• 1995

원자로에서 펌프에 의해 야기되는 맥동 압력은 원자로 내부 구조물에 진동과 손상을 줄 수 있기 때문에 관심이 증가되고 있다. 본 연구에서는 냉각관과 환형관(원자로 압력 용기와 노심 보호 지지대 사이)으로 구성된 기하 형태에서 펌프에 의해 야기되는 맥동 압력을 해석할 수 있는 수력학적 모델을 개발하였다. 수학적 지배 방정식은 압축성, 비점성 유체에 대해 선형화된 Navier-Stokes 방정식이다. 냉각관과 환형관을 따로 분리하여 해석하고 두영역의 커플링 영향을 고려하였다. 또한 본 기하 형태에서 펌프맥동 압력에 영향을 미치는 주요 기하 인자에 대한 평가를 수행하였다. 본 해석 결과와 실험차를 비교하여 만족할 만한 결과를 얻었다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.801-806
• /
• 2008

The best plan is that the insulation performance should be improved because the insulation and airtight of building envelopes have an effect on the energy consumption basically. New insulation materials, which have the high performance and are above insulation standard, have been developed steadily. Because there are not studies on the building energy rating system and economic evaluation considering new insulation materials, these matters should be studied. In result alternatives, which applied 6 high performance material each, influence, reduce the annual heating energy and raise the building energy rating. Applying the vacuum insulation material(Case1,2) and vacuum or triple glazing can retrieves the investment with $120 and $$140{\sim}150$ per barrel each.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.436-439
• /
• 2008

This paper is to research the heat transfer performance of the sintered pipe. Recently, oil prices is to be 127 $ per barrel, we expect higher costs this summer. We promote alternative fuels, after oil and gasoline prices reached record highs. The governments have made efforts to avoid future crisis by continuing the move toward renewable energy and energy saving. In this paper, we have fabricated a sintered pipe, the heat transfer performance of sintered pipe is achieved experimentally. The pipe is copper tube of outer diameter of 15.88 mm, the length of the pipe is 800 mm. Based on the experimental results, it is shown the overall heat transfer coefficient of sintered pipe is increased as compared with that of a straight pipe, is equal as compared with that of a spiral pipe. The overall heat transfer coefficient was $0.075{\sim}0.09\;kW/^{\circ}C$