• 대한원격탐사학회지
• /
• 제34권4호
• /
• pp.639-647
• /
• 2018

This paper presents TerraSAR-X and KOMPSAT-5 sigma nought variation according to season and antenna observation configuration in Mongolia. Two types of landcover including bare surface and cropland were examined. The seasonal variation of sigma nought in cropland was about 7 dB and particularly a significant sigma nought reduction occurred after harvest. On the contrary, the Mongolia bare surface provides a consistent sigma nought values for several years with an annual variation less than 2.5 dB of standard deviation. However, the bare soil was relatively sensitive to look-direction (or ascending or descending mode) as well as incidence angle while the cropland was almost independent of antenna look-direction and small incidence angle changes. Although the look-directional variation of bare surface sigma nought was observed in this study, the look-direction anisotropic nature of the surface was not well examined. A further study would be required to account for this feature with various SAR observation configurations.

• Nuclear Engineering and Technology
• /
• 제27권6호
• /
• pp.888-893
• /
• 1995

맨봉 배열에 의해 형성되는 부수로를 흐르는 난류 유동장의 구조는 피치 대 봉직경의 비에 따라 변하게 된다. 피치 대 봉직경 비가 큰 경우에는 난류 응력 분포가 관 유동의 분포와 유사하다 그러나 피치 대 봉직경 비가 작은 경우에는 특히 간극 영역에서 난류 특성이 관 유동의 분포와는 달라진다. 완전히 발달된 맨봉 주위의 난류 유동장에서 난류응력과 난류운동에너지 사이의 선형 관계가 개발되었다. 개발된 상관 관계식은 난류 연구에 응용되는 여러 이론적 분석에 연관지어 사용될 수 있다.

• Journal of electromagnetic engineering and science
• /
• 제10권4호
• /
• pp.212-218
• /
• 2010

The radar backscatter from various earth surfaces is sensitive to the frequency of the incident wave. This study examined the radar sensitivities for surface parameters such as soil moisture content and surface roughness of both bare and vegetated surfaces at X-band. Because L-band frequencies are often used for sensing the surface parameters, the sensitivities of X-band are also compared with those of the L-band. The sensitivities of the X-band radar backscatter were examined with respect to soil moisture content and surface roughness of rough bare soil surfaces. These sensitivities were also examined using the same parameters for vegetated surfaces for various vegetation densities and incidence angles. Use of the X-band radar for soil moisture detection was as effective as L-band radar for bare soil surfaces. For vegetated surfaces, the soil moisture could be detected using an X-band radar at lower incidence angles, where the upper limit of the incidence angles was dependent on vegetation density.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.432-435
• /
• 2005

The Mega-pixel camera phones become main trends in mobile phone market. The lens modules used in mesa-pixel camera phones need high resolution. One of the main factors of resolution drop is the defects of bare lens. Though there are many advantages in auto-inspection of defects of bare lens, high technical problems take the defect inspections to be done with manual process. In this paper, the type and the source of defects were described and bare lens defect auto-inspection system design was explained. The designed auto-inspection system is composed of illumination optics part, focusing optics part and auto-moving system. With the proposed auto-inspection system, fast and uniform inspection of bare lens can be achieved.

• Journal of the Korean Physical Society
• /
• 제73권9호
• /
• pp.1346-1350
• /
• 2018

An electrode-evaporation technology on both the top and bottom sides of the bare vertical-type single chip separated from the traditional substrate by cooling, was developed for III-nitride vertical-type single chip LEDs with thick GaN epilayer. The post-process of the cooling step was followed by sorting the bare vertical-type single chip LEDs into the holes in a pocket-type shadow mask for deposition of the electrodes at the top and bottom sides of bare vertical-type single chip LEDs without the traditional substrate for electrode evaporation technology for vertical-type single chip LEDs. The variation in size of the hole between the designed shadow mask and the deposited electrodes owing to the use of the designed pocket-type shadow mask is investigated. Furthermore, the electrical and the optical properties of bare vertical-type single chip LEDs deposited with two different shapes of n-type electrodes using the pocket-type shadow mask are investigated to explore the possibility of the e-beam evaporation method.

• 대한설비공학회지:설비저널
• /
• 제10권3호
• /
• pp.220-227
• /
• 1981

The purpose of this paper is to investigate the potential ability of sintered metal tube to promote heat transfer. In the experiment for Freon - 11, the boiling heat transfer on the sintered metal tube of bronze element is investigated and compared with that of the bronze tube (bare tube) atmospheric pressure. The experimental results are obtained as follows : 1) For sintered metal tubes of bronze element with particle diameters which ranges from $79({\mu})\;to\;461({\mu})$ and bare tube, boiling characteristic curves are expressed as : a) Sintered metal tube $$q{\propto}{\Delta}T^{1.05\~1.373}$$ b) Brae tube $$q{\propto}{\Delta}T^{3.096}$$ 2) Compared with that of the bare tube at low temperature difference$({\Delta}T_{sat})$, boiling heat transfer coefficient of the sintered bronze tube are relatively high. 3) There is tendency that curves of boiling heat transfer coefficients of sintered ·bronze tube and bare tube approach each other at rather high temperature difference. It is due to the increasing rate of the former heat transfer coefficient along with temperature difference is smaller than that of the latter. 4) Referring to particle diameter, optimum condition, i. e. , maximum heat transfer coefficient is found to be at approximately 2 mm thickness of sintered layer with $D_p=150({\mu})$.

• 한국해양공학회지
• /
• 제38권3호
• /
• pp.137-147
• /
• 2024

Green hydrogen presents a sustainable and environmentally friendly solution for clean energy production and transportation. This study aims to identify the optimal profile of green hydrogen transportation risers originating from a floating offshore wind turbine (FOWT) integrated with a hydrogen production facility. Employing the Cummins equation, a fully coupled dynamic analysis for FOWT with a flexible riser was conducted, with the tower, mooring lines, and risers described using a lumped mass line model. Initially, motion response amplitude operators (RAOs) were compared with openly published results to validate the numerical model for the FOWT. Subsequently, a parametric study was conducted on the length of the buoyancy module section and the upper bare section of the riser by comparing the riser's tension and bending moment. The results indicated that as the length of the buoyancy module increases, the maximum tension of the riser decreases, while it increases with the lengthening of the bare section. Furthermore, shorter buoyancy modules are expected to experience less fatigue damage, with the length of the bare section having a relatively minor impact on this phenomenon. Consequently, to ensure safety under extreme environmental conditions, both the upper bare section and the buoyancy module section should be relatively short.

• 한국ITS학회 논문지
• /
• 제10권1호
• /
• pp.42-48
• /
• 2011

본 논문에서는 GaN HEMT (Gallium Nitride High Electron Mobility Transistor) bare-chip을 이용하여 X-대역에서 수동로드 풀(Passive load-pull)을 수행하였다. 열로 인한 특성 변화가 최소화 된 동작 조건을 얻기 위해 드레인 바이어스 전압과 입력 RF 신호를 펄스로 인가하였다. 전자기장 시뮬레이션과 회로 시뮬레이션을 병행하여, 와이어 본딩 효과를 고려하여 드레인 경계면에서의 정확한 임피던스 정합 회로를 구현하였다. 임피던스를 변화시키기 위해 마이크로스트립 라인 스터브의 길이가 조절 가능한 회로를 설계하였다. 펄스 로드 풀 실험 결과 8.5 GHz에서 9.2 GHz 대역에서 최대 42.46 dBm의 출력 전력을 얻었으며, 58.7%의 드레인 효율 특성을 얻었다.

• Transactions on Electrical and Electronic Materials
• /
• 제16권5호
• /
• pp.268-273
• /
• 2015

While analyzing the specimens before and after the thermal shock test, we found that the power drop rate of the bare cell was 5.08%, while the power drop rate of the ribboned cell was 16.49%. In comparative terms, the efficiency was lower at the ribboned cell than at the bare cell. While analyzing through EL (Electroluminescence) shots and cross sections, we tried to decipher the exact cause of the power drop. Although mere color change of the cell was observed at the surface of the bare cell, no abnormality could be found inside the cell. On the surface of the ribboned cell, the short circuit of gridfinger extended from the front part of the front electrode of the ribboned cells. Therefore, cracks occurred on the surface of the cell. Cracks also appeared inside the cell. While analyzing the I-V curve, we determined an increase in the leakage current and an increase of resistances in series in the bare cell. In the ribboned cell, the resistances in parallel reduced remarkably. An increase of resistances in series could also be verified. Conclusively, we deduced that the power drop rate in the bare cell is a life span of the cell itself; aging is the cause of power drop rate in cells. In case of ribboned cell, the power drop rate was directly influenced by internal cracks and an intermetallic compound layer joining the ribbon at the front electrode.

• 마이크로전자및패키징학회지
• /
• 제14권4호
• /
• pp.87-92
• /
• 2007

[ $CaAl_{12}O_{19}:Mn^{4+}$ ] 적색 형광체는 $Mn^{4+}$이온이 0.02 mol 첨가되었을 때 최대 발광 세기가 관찰되었고 $1600^{\circ}C$, 3시간 소성조건에서 우수한 결정성과 발광 효율을 나타내며 중심 파장이 658 nm에서 관찰되었다. 본 연구에서 개발된 $CaAl_{12}O_{19}:Mn^{4+}$ 형광체를 에폭시와 함께 1:3으로 혼합하여서 InGaN UV 발광체의 Bare 칩 위에 코팅하여 중심파장이 658 nm인 적색 LED를 제조하였다. 적색 형광체를 이용하여, 기존의 UV LED를 여기 광원으로 다양한 느낌의 백색 발광체를 설계 할 수 있을 것이다.