• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.4 s.119
• /
• pp.416-422
• /
• 2007

In this paper, a broadband 2-way power divider which can be used from 20 MHz to 500 MHz in the V/UHF band is designed using transmission-line transformer and ferrite toroid. A 2:1 impedance transformer instead of the conventional 4:1 impedance transformer is realized and this 2:1 transformer is connected with the conventional bridge-type 2-way divider to form a 2-way power divider. Insertion loss of about 3.5 dB, isolation of less than -10 dB, and return loss of less than -10 dB in most band of interest are measured.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.2
• /
• pp.62-66
• /
• 2010

In this article, a oscillator at X-band with a double H-shape metamaterial resonator (DHMR) based on high-Q is proposed with metamaterial structure to improve Ihe phase noise and output power. The proposed oscillator is required low phase noise and high output power for the high performance frequency synthesizer. DHMR is designed to be high-Q at resonance frequency through strong coupling of E-field. This character makes phase noise excellent. The oscillator using DHMR is oscillated in X-band so as to apply frequency synthesizer of radar systems. The output power is 4.33 dBm and the phase noise is -108 dBc/Hz at 100 kHz offset of carrier frequency.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.2
• /
• pp.65-70
• /
• 2004

This paper presents a novel linearization scheme for a nonlinear RF amplifier It is based on the amplitude modulation with envelope signal. The 3rd order distortion generator is composed of two FETs and it adopts a balanced structure for the purpose of main carrier cancellation. The amplitude and phase of the IM3 component can be controlled at RF band. This predistorter is implemented and tested at the KOREA PCS Tx. band (1840∼1870MHz). Experimental results of two-tone test show that the IM3 cancellation is achieved about 30-40 ㏈ for the wide dynamic range. The adjacent channel power ratio is improved by over 10 ㏈ at the broad-band CDMA signal with a peak to average power ratio of l0㏈, and this improvement is maintained through a wide range of output power levels.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.6
• /
• pp.129-135
• /
• 2022

In this paper, a 100 W SSPA in Ka-band was developed by combining 16 GaN MMICs which were 10 W amplifiers, respectively. The gate voltage of SSPA was controlled to minimize the effect of SSPA noise on the receiver during the receiving time. And the transmit power could be reduced about 20 dB to prevent the receiver from being saturated by a large signal from a nearby target. At 10%, 40% duty rato, the peak power and the power efficiency at center frequency were measured 52.4 dBm, 19.2%, and 51.6 dBm, 16.6% respectively.

• Proceedings of the IEEK Conference
• /
• 2000.09a
• /
• pp.923-926
• /
• 2000

In this paper we address the problem of detecting and estimating an unknown narrow band signal in a noise interference environment A new practical band estimation method, yielding good performance even in case of finite-length data, is presented. More specifically, wavelet packet transform is utilized to detect the more accurate time-variant band, then we estimate the power from wavelet filter-coefficients of the respective band. Also, third-order cumulants, and projection cross-correlation (PCC) criterion are utilized to achieve an effective SNR improvement for the time-variant band estimation. In case of time variant band estimation, the PCC method yields better performance than the correlation method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.435-443
• /
• 2001

As power durable RF SAW filters, AL-(0∼2wt%)Cu alloy multi-layered thin electrodes were deposited on 42° LiTaO$_3$ piezoelectric substrates by magnetron sputtering process, and then ladder-type RF SAW filters, satisfying the electrical specification of CDMA transmission band, were fabricated through optimizing SAW resonator structures. The temperature of film electrodes in SAW filter was increased with RF power, and reached the maxima to cause a failure of SAW filters at the cut-off frequencies of the RF filter band. As RF power increases, the electrodes of Al-Cu alloy showed higher power durability than that of pure Al. The multi-layer laminated film of Al-1wt.% Cu/Cu/Al-1wt%Cu resulted in the best power durability up to 4W of RF power. Every film electrode, however, was destroyed within seconds whenever applying a critical RF power to SAW filters, regardless of the composition and structure of film electrodes. The breakdown of film electrodes under FR power seems to believe due to the fatigue of electrodes caused by repetitive cyclic stress of surface acoustic wave, which is amplified as RF power increases.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.3
• /
• pp.283-289
• /
• 2014

This paper carries out a series of analysis of power system using Gallium Nitride (GaN) FET which has wide band gap (WBG) characteristics comparing to conventional Si MOSFET-used power system. At first, for comparison of each semiconductor device, the switching-transient parameter is quantitatively extracted from released information of GaN FET. And GaN FET model which reflect this dynamic property is configured. By using this model, the performance of GaN FET is analyzed comparing to Si MOSFET. Also, in order to enable a representative assessment on the power system level, Si MOSFET and GaN FET are applied to the most common structure of power system, full-bridge, and each power systems are compared based on various criteria, such as performance, efficiency and power density. The entire process is verified with the aid of mathematical analysis and simulation.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.17-21
• /
• 2004

We demonstrate an S/S＋band discretely tunable thulium doped fiber laser (TTDFL), anchored on a 50-㎓ ITU-T grid. Investigating the inversion analysis of the thulium doped fiber (TDF) in applying a dual wavelength (1.4 m and 1.5 m) pumping scheme, a laser whose tuning range covers most of the S/S＋band has been obtained. Within the wide 3-㏈ bandwidth of 65.1 nm, the output power of the tunable laser exceeds 6.1 ㏈m with very flat spectral profile and the number of DWDM channels generated is as large as 178. If we increase the subsidiary pump power to 22 ㎽, the bandwidth is expanded up to 66.2 nm. By controlling the temperature of the fine grid filter, we have also shown that the frequency locking capability of the laser can be improved. The laser developed in this work is expected to be utilized as a practical optical source providing reference wavelengths in the S/S＋band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.853-861
• /
• 2009

In this paper, we propose the architecture of a multi-band receiver which can receive X-band, Ku-band, K-band and Ka-band signals. For implementing this architecture, we designed a wideband and high power VCO with a buffer stage. In order that a buffer does not affect the characteristic of a oscillation in steady state condition, output impedance of a oscillation part and input impedance of a buffer are orthogonally crossed. The fabricated VCO meets the performance parameter of the multi-band receiver which has a $14.00{\sim}15.20\;GHz$ bandwidth with respect to the tuning voltage, $0.0{\sim}8.0\;V$, and output power of $12{\sim}13\;dBm$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.5
• /
• pp.461-466
• /
• 2012

This paper describes the development and test result of X-band Transmitter flight model(FM) of STSAT-3 by satellite research center(SaTReC), KAIST. The communication sub-system of STSAT-3 is consist of two different frequency band channels. S-band frequency is used for Telemetry & Command, and X-band frequency is used for mission data. Payload observations data in Mass Memory Unit (MMU) is modulated by QPSK modulator in X-band Transmitter, and then QPSK modulation signal is transmitted to antenna through transfer switch. In this Paper, we described the results of modulation, low-pass filter design, power amp development, and switch test. The FM XTU is delivered Spacecraft Assembly, Integration and Test(AIT) level through the completion of functional Test and environmental(vibration, thermal vacuum) Test successfully.