• 소음진동
• /
• 제5권1호
• /
• pp.95-106
• /
• 1995

Flow-induced vibration in heat exchanger (or fuel rod) in nuclar power plant can cause dynamic interactions between tubes and tube supports resulting in fretting-wear. To increase the reliability and design life of heat exchanger components, design criteria that establish acceptable limits of vibration and minimize fretting wear are necessary. The fretting-wear rate is dependent upon material combination, contact configuration, environmental conditions and tube-to tube support dynamic interaction. It is demostrated that the fretting -wear rate correlates well with tube-to-support contact force or work rate. The tube-to-support dynamic interaction, which consists of dynamic contact forces and tube motion, is used to relate single-span wear data to real heat exchanger configurations consisting of multi-span tube bundles. This paper describes the test facility to measure tube-to-support dynamic impact force and reports its dynamic characteristics through the four impact tests - a force transduces independent and external impact tests, central ring inside impact test and additional cylinder impact test. Through the tests the impact parameter change dependent upon the material difference of impacting ball is studied, and the impact parameters of Force Transducer Assembly components are measured. And also the dynamic behavior of Force Transducer Assembly is analyzed. The force measurement technique herein is shown to provide a reasonable measure of dynamic contact forces.

• 로봇학회논문지
• /
• 제10권4호
• /
• pp.200-212
• /
• 2015

In classical dynamics, the coefficient of restitution is one of variables to estimate the amount of impulse. In general, we have considered the coefficient of restitution as a constant value. However, coefficient of restitution (COR) is the function of contact material and colliding velocity. Furthermore, COR is also a function of contact area. Thus, without considering the variable characteristic of COR, the actual motion of an object just after impact is not the same as we expect. A general COR model is proposed in this work and its effectiveness is verified through a cart impact experiment and its result is applied to simulation of a ball impact problem. A three-degree-of-freedom manipulator is employed as a test-bed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.56-56
• /
• 2008

최근, 비납 또는 납의 함량을 줄인 압전 세라믹에 대한 관심이 증가하고 있고, 그에 따른 여러 연구가 활발히 이루어지고 있다. 납을 포함하는 세라믹은 높은 소성온도에서 납의 휘발로 인한 특성저하와 환경오염 등이 문제가 된다는 것을 우리는 익히 알고 있다. 그렇기 때문에 PZT계 세라믹스를 대체할 우수한 특성을 가지는 새로운 비납 세리믹스의 조성개발이 시급하다. 비납계 세라믹스 중에서 NKN계를 바탕으로 하는 세라믹스는 가장 기대되는 재료이다. 일반적인 소성에서 순수한 NKN 세라믹은 가장 높은 압전 $d_{33}$상수가 100 pC/N이 넘지 않는다. 그런데 페로브스카이트 구조로된 NKN세라믹스의 A-site에 $Li^{1+}$이온을 치환하면 압전 특성을 향상시킬 수 있다. 그리고, 압전세라믹에서 분극처리는 필수적인데 분극처리는 압전성을 부여할 뿐 아니라 다른 물성도 변화시킴은 잘 알려져 있다. 그러므로 그에 대한 연구 또한 중요한 의미를 갖는다. 따라서 이번 연구에서는 NKN세라믹스에 $Li_2CO_3$를 소결조제로 첨가하여 시편을 제작하였고, 제작된 시편의 특성을 분극전계에 따라 조사하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.708-711
• /
• 1999

The Cu/Ni/Au lamellar structure is extensively used as an under bump metallization on silicon file, and on printed circuit board(PCB) pads. Ni is plated Cu by either electroless Ni plating, or electrolytic Ni plating. Unlike the electrolytic Ni plating, the electroless Ni plating does not deposit pure Ni, but a mixture of Ni and phosphorous, because hypophosphite Is used in the chemical reaction for reducing Ni ions. The fracture crack extended at the interface between solder balls of plastic ball grid (PBGA) package and conducting pads of PCB. The fracture is duets to segregation at the interface between Ni$_3$Sn$_4$intermetallic and Ni-P layer. The XPS diffraction results of Cu/Ni/Au results of CU/Ni/AU finishs showed that the Ni was amorphous with supersaturated P. The XPS and EDXA results of the fracture surface indicated that both of the fracture occurred on the transition lesion where Sn, P and Ni concentrations changed.

• 한국전기전자재료학회논문지
• /
• 제17권4호
• /
• pp.390-395
• /
• 2004

In order to analyze the physical and chemical characteristics of home production porcelain insulators by change of the alumina addition amount, 360001bs ball socket type suspension insulators which were manufactured in 1989, 1995 and 2001 removed in transmission line and an experiment was performed. By the result, 8 wt.％ alumina that influences the mechanical properties and arc resistance properties in case of insulators that were manufactured in 1989 was contained, and the relative density and the fracture toughness of insulators appeared by 94.2％ and 1.4 ㎫$.$ $M^{\frac{1}{2}}$, respectively. However, 12 wt.％ alumina was contained in case of insulators that were manufactured in 1995, and the relative density and the fracture toughness of insulators appeared preferably lower by 92％ and 1.3㎫$.$ $M^{\frac{1}{2}}$, respectively. Amount of alumina was contained most by 17 wt.％ in case of insulators that were manufactured in 2001. It was confirmed that the electrical and mechanical characteristics such as the relative density and the fracture toughness appeared excellently by 96％ and 1.7㎫$.$ $m^{\frac{1}{2}}$, respectively.

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.107-114
• /
• 2012

Fracture of brittle material due to dynamic load such a particle impact has been reported by many researchers as the fracture behavior by variation of stress for a short minute. Especially, the brittle material, such a ceramic, applied to the structural component of machine, is considered as the important project. In order to evaluate the improvement of impact resistance, the particle impact test for the $Al_2O_3-TiO_2$ coated glass is practiced. And then, the damage variation according to the impact energy of steel ball was evaluated. There was a large improvement by the ceramic coating on the surface of a glass substrate. The damage volume was especially imported to evaluate damage behavior in quantity. These data were plotted on logarithmic coordinate and experimental equations were induced by data analysis based on test results. And the variation of critical energy for crack initiation was analyzed with critical impact energy when each crack occurs.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.297-301
• /
• 2002

High-speed machining generates concenter thermal/frictional damage at the cutting ed rapidly decreases the tool life. This paper I at determining the effect of cutter orienter the cutting environment on tool life, tool mechanism when down milling. In this paper, experiments were carried out in various tool and cutting environments, such as dry, wet compressed chilled air, tool life were measu evaluate machinability in high-speed milli difficult-to-cut material and die steel, Tool measured in horizontal upwards, horiz downwards, vertical upwards and vert downwards. In addition, tool life was measur dry, wet and compressed chilled air. For this a compressed chi1led-air system was manufact The results show that a horizontal cutter ori provided a longer tool life than a vertical orientation. With respect to the cutting envi compressed chilled air increased tool life. H the wet condition decreased tool life due thermal shock caused by excessive cooling high-speed mill ins and the compressed chilled had little effect.

• Carbon letters
• /
• 제9권3호
• /
• pp.188-194
• /
• 2008

Porous carbon materials synthesized from various plant derived precursors i.e. seeds of [Castor (Ricinus communis), Soap nut (Sapindus sp.), Cashew-nut (Semecarpus anacardium), Jack fruit (Artocarpus heterophyllus), Safflower (Carthamus tinctorius), Ambadi (Crotolaria juncea), Neem (Azadirachta indica), Bitter Almond (Prunus amygdalus), Sesamum (Sisamum indicum), Date-palm (Phoenix dactylifera),Canola (Brassica napus), Sunflower (Helianthus annulus)] and fibrous materials from [Corn stem- (Zea mays), Rice straw (Oryza sativa), Bamboo (Bombax bambusa) and Coconut fibers (Cocos nucifera)] were screened to make supercapacitor in 5M KOH solution. Carbon material obtained from Jack fruit seeds (92.0 F/g), Rice straw (83.0 F/g), Soap nut seeds (54.0 F/g), Castor seeds (44.34 F/g) and Bamboo (40.0 F/g) gave high capacitance value as compared to others. The magnitude of capacitance value was found to be inversely proportional to the scan rate of measurement. It is suggested that carbon material should possess large surface area and small pore size to get better value of capacitor. Moreover, the structure of carbon materials should be such that majority of pores are in the plane parallel to the plane of electrode and surface is fluffy like cotton ball.

• 한국산학기술학회논문지
• /
• 제9권6호
• /
• pp.1518-1522
• /
• 2008

본 연구에서 개발한 벤딩다이시스템(Bending Die System)제작기술은 부가가치가 매우 높은 소량 다품종 건축용 내 외장재의 금속 패널 코너가공법에 관한 것이다. 금속 금구류 및 건축용 내 외장재로 사용되는 2.5mm이상 되는 금속강판을 사용함에 있어서 가장 문제가 되는 직각코너링 접합부위에서 발생되는 내식성, 내후성, 및 디자인을 향상시키므로 품질의 향상뿐만 아니라 소량 다품종의 생산성을 증대시킬 수 있는 국내 최초 금속패널 코너가공을 할 수 있는 벤딩다이시스템을 설계하여 제작하였다. 이를 제작하여 경제적, 기술적으로 고부가가치를 창출하여 수출증대에 기여할 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 방전 플라즈마 유기절연재료 초전도 자성체연구회
• /
• pp.173-176
• /
• 2004

The piezoelectric ceramics for AE sensor piezoelectric devices are desirable to possess higher resonance vibrations. The compositions of $0.9Pb(Zr_xTi_{1-x})O_3-0.1Pb(Mn_{1/3}Nb_{1/3}Sb_{1/3})O_3$ (PZT-PMNS) in this work are selected for obtaining especially large electromechanical coupling factor, high mechanical quality factor and high Curie temperature. This ceramic has higher piezoelectric activity and higher electromechanical coupling factor, but the ceramic has lower Curie temperature. The piezoelectric and dielectric characteristics of PZT-PMNS ternary system are investigated as functions of $Ti^{2+}$, $Zi^{2+}$ mol rate. As the results, MPB(morphotropic phase boundary) in this piezoelectric ceramic is x=0.522. Resonance vibrations of PZT ceramics are investigated as ball-bearing drop test. For the use of AE sensor that driving with pre-amplifier, filter circuit after packed this ceramic and an elastic body.