• 제목/요약/키워드: average spacing

검색결과 206건 처리시간 0.025초

On the Optimization of Raman Fiber Amplifier using Genetic Algorithm in the Scenario of a 64 nm 320 Channels Dense Wavelength Division Multiplexed System

  • Singh, Simranjit;Saini, Sonak;Kaur, Gurpreet;Kaler, Rajinder Singh
    • Journal of the Optical Society of Korea
    • /
    • 제18권2호
    • /
    • pp.118-123
    • /
    • 2014
  • For multi parameter optimization of Raman Fiber Amplifier (RFA), a simple genetic algorithm is presented in the scenario of a 320 channel Dense Wavelength Division Multiplexed (DWDM) system at channel spacing of 25 GHz. The large average gain (> 22 dB) is observed from optimized RFA with the optimized parameters, such as 39.6 km of Raman length with counter-propagating pumps tuned to 205.5 THz and 211.9 THz at pump powers of 234.3 mW, 677.1 mW respectively. The gain flattening filter (GFF) has also been optimized to further reduce the gain ripple across the frequency range from 190 to 197.975 THz for broadband amplification.

충돌분류시스템의 열전달 특성에 관한 수치적 연구 (Numerical Study on Heat Transfer Characteristics in Impinging Air Jet System)

  • 금성민;김동춘
    • 한국태양에너지학회 논문집
    • /
    • 제23권4호
    • /
    • pp.55-61
    • /
    • 2003
  • Heat transfer characteristics for an air jet vertically impinging on a flat plate with a set of hybrid rods was investigated numerically using the RNG k-$\varepsilon$turbulent model. A commercial finite-volume code FLUENT is used. The rods had cross sections of half circular and rectangular shapes. The heating surface was heated with a constant heat flux value of $1020W/m^2$. Parameters investigated were the jet Reynolds number, nozzle -to-plate spacing, the rod pitch and rod-to-plate clearance. The local and average Nusselt number were found to be dependent on the rod pitch and the clearance because installing rods disturbed the flow. Higher convective heat transfer rate occurred in the whole plate as well as in the wall jet region.

철근콘크리트 벽체의 초기재령 거동 해석 (Early-Age Behavior of Base Restrained RC Walls)

  • 곽효경;하수준
    • 한국전산구조공학회:학술대회논문집
    • /
    • 한국전산구조공학회 2003년도 가을 학술발표회 논문집
    • /
    • pp.251-258
    • /
    • 2003
  • The early -age behavior of base restrained reinforced concrete (RC) walls is analyzed using a three-dimensional finite element method in this study. After calculating the temperature and internal relative humidity variations of an RC wall, determination of stresses due to thermal gradients, differential drying shrinkage, and average drying shrinkage is followed, and the relative contribution of these three stress components to the total stress is compared. The mechanical properties of early-age concrete, determined from many experimental studies, are taken into consideration, and a discrete reinforcing steel derived using the equivalent nodal force concept is also used to simulate the cracking behavior of RC walls. In advance, to Predict the crack spacing and maximum crack width in a base restrained RC wall, an analytical model which can simulate the post-cracking behavior of an RC tension member is introduced on the basis of the energy equilibrium before and after cracking of concrete.

  • PDF

직렬 관군에서 지열수스케일의 파울링 영향에 관한연구 (A Study on the Fouling Effect of Geothermal Water Scale in In-line tube Bank)

  • 윤석범
    • Journal of Advanced Marine Engineering and Technology
    • /
    • 제23권2호
    • /
    • pp.131-139
    • /
    • 1999
  • An experimental study was conducted to investigate the fouling effects of geothermal water scale deposited onto a heating surface upon its forced convection heat transfer characteristics. Scales deposited onto the heating surfaces of heat exchangers seriously reduce the heat transfer perfor-mance and also increase the hydrodynamic drag. Accordingly fouling is an important problem in the design and operation of heat exchangers. The cylinders were settled in tandem with equal dis-tance between neighbouring cylinders and only the test cylinder was heated under the condition of constant heat flux. The Reynolds number was varied from 13000310 through 50003100. It is found that the heat transfer of the in-line tube banks greatly varies with the fouling of geothermal water scale especially its scale height. Further the local and average Nusselt numbers strongly depend upon the cylinder spacing and the Reynolds number.

  • PDF

이동평판에 작용하는 슬롯 충돌제트의 유동 및 열전달에 관한 수치적 연구 (A Numerical Study of Turbulent Flow and Heat Transfer due to Slot-jet impinging on a Moving flat plate)

  • 이종석;김동건;김문경;윤순현;김봉환
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2008년도 추계학술대회B
    • /
    • pp.2798-2803
    • /
    • 2008
  • The confined slot air jet impinging normally on a moving flat surface has been investigated numerically by using commercial CFD code Ansys CFX-V11. Turbulent flows are modeled using k-w turbulence model. Two-dimensional turbulent flow is considered. Calculations were conducted for a nozzle-to-plate spacing of eight slot nozzle width, at three Reynolds number(Re=4500, 6700 and 10,000) and four surface-to-velocity ratios i.e. 0, 0.25, 0.5 and 1. Results are compared against corresponding cases for heat transfer from a stationary plate. Local Nusselt number is calculated under constant wall temperature condition. The analysis reveals that the average Nusselt number increases considerably with the jet exit Reynolds number, but decrease with the plate velocity.

  • PDF

하이브리드 로드를 갖는 충돌공기제트의 열전달특성에 관한 연구 (Heat Transfer Characteristics in Impinging Air Jet with Hybrid Rod)

  • 표창기;박상록;김동춘;금성민;임장순
    • 설비공학논문집
    • /
    • 제12권3호
    • /
    • pp.277-283
    • /
    • 2000
  • The heat transfer characteristics for air jet vertically impinging on a flat plate which had a set of hybrid rod were investigated experimentally. The rod had a cross section made with a half of circular cross section and that of rectangular and was installed in front of the plate. The heating surface was given constant heat flux value of 1020 W/$m^2^{\circ]C$ and the problem parameters investigated were jet Reynolds number, nozzle-to-plate spacing and the rod size. The local and local average Nusselt number characteristics were found to be dependent on the rod size because the flow was disturbed by installing the rod. Higher convective heat transfer rate occurred in the whole plate as well as in the stagnation region.

  • PDF

금호지구 저습답의 암거배수효과에 관한 연구(I) (Studies on Wet Paddy Field Underdrainage Improvement in the Gum-Ho Area (I))

  • 김조웅;김시원
    • 한국농공학회지
    • /
    • 제22권4호
    • /
    • pp.82-95
    • /
    • 1980
  • This paper complies the results of the studies so far made on the subsoil improvement of subsurface drainage systems for wet paddy fields (those were located in the Gum-Ho area in Kyung Buk province) which had poor permeability and a high water table. In general, a drainage problem is an excess of water on the ground surface which can effect the productivity and bearing capacity of the soil. With drain pipe systems, (According to their depths and spacing) it may be possible to correct that problem. The experimentation consisted of three test plots, two of which included drain pipe systems with varing depths and width spacing of the pipes. The third plot (C) was an ordinary plot being exempt of a drain pipe system. In detail, the depth of plot A was 80 cm, and the width spacings began at 2. Om and increased by 2. Om up to 10. 0m. The depth of plot B was 60cm and the width spacing was the same as plot A. These tests were performed to research specific details; such as crop yeild, bearing capacity of the soil, the amount of underdrainage, surface cracks, root distribution, the water table level, the consumptive water depth and the soil moisture content. The test period lasted three years, from 1977 thru 1979. The results obtained were as follows: 1. During the test period, the weather conditions for the area tested were in accordance with the annual average for that area. Furthermore the precipitation factor during the spring cultivation season, the intermediate drainage period and the harvest drainage period was of optimum conditions for controling surface cracks, because of less precipitation than evaporation. 2. The difference in the level of the ground water table in plots A and B was hardly noticable, but the difference in the test plots and the ord. plot was greatly noticable. The test plots (A, B) were 30 to 40cm lower than the ordinary plot. On the whole, the ground water table of the ord. plot always stayed at a level of 15-20cm beneath the surface of the soil, the ground water table of the test plot A showed The difference in the depth of the pipe lower than the test plot B, while the test plots showed a remarkable descending effect. 3. The soil temperature in plot A was slightly core than in plot B with a difference of 0. 47$^{\circ}$C, but plot A was 1. 6$^{\circ}$C higher than the ord. plot during the flooding period, but after drainage the temperature difference climed to 2. 0$^{\circ}$C. 4. During the 3rd test year, the values of the cracks were recorded with the values of 59cm in plot A, 42cm in plot B and 15cm in the ordinary plot. Plots A and B had increased 2.5 times the value of the first year while the ordinary plot had remained the same. 5. The root weight of the rice was measured at a value of 77.2 gr. for plot A, 73.5 gr. for plot B and 65.3 gr. for the ord. plot. Therefore, the root growths in plots A and B were much more energetic than in the ord. plot. 6. The consumptive water depth measured during the 3rd year resulted in the values of 26. 0mm per day for plot A, and 24.9 mm per day for plot B, respectively. Therefore, both plot A and plot B maintained the optimum consumptive water depths, but the ordinary plot only obtained the value of 12.3 mm per day, which clearly showed less than the optimum consumptive water depth which is 20 to 30 mm/day. 7. The soil moisture content is in direct relationship to the ground water level. During drainage, test plot A decreased in its ground water level much more rapidly than the other two plots. Therefore, plot A had a much less soil moisture content. But this decreased water level could be directly effected by the weather conditions. 8. The relationship between the bearing capacity and the soil moisture content were directly inversely proportional. It can be assumed that the occurence of soil creaks is limited by the soil moisture content. Therefore, the greater the progress of the surface creaks resulted in a greater bearing capacity. So, tast plot A with a greater amount of surface cracks than the other test plots resulted in a greater bearing capacity. But, the bearing capacity at the harvest season could be effected by the drainage during the intermediate drainage period and by the weather conditions. 9. Comparing the production of the test plots to the ord. plot; there was an increased value of 840kg for plot A, 755kg for plot B and 695kg for the ord. plot in the rough rice. Therefore, plot A had an increase of 20% over the ordinary plot. The possibility of producing double crops was investigated. The effects on barley production in the test plots showed a value of 367kg per 10 acres, which substantiated the possibility of double crops because that value showed an increased value over the average yearly yield for those uplands. 10. So as a result, it can be recommended that by including a drain pipe system with the optimum conditions of an (80cm centimeter) depth and a (l0m) spacing will have a definite positive effect on the over all production capacity and quality of wetpaddy fields.

  • PDF

양생온도에 따른 90 MPa 수준의 고강도 철근 콘크리트 보의 휨거동 (Flexural Behavior of High-strength Concrete Beams of 90 MPa According to Curing Temperature)

  • 황철성
    • 한국구조물진단유지관리공학회 논문집
    • /
    • 제21권5호
    • /
    • pp.134-140
    • /
    • 2017
  • 본 연구에서는 양생조건이 다른 압축강도 90 MPa 수준의 고강도 콘크리트 부재의 휨거동 실험을 수행하였다. 실험변수는 정상 및 저온 양생 조건, 인장 철근량 및 콘크리트 압축강도 수준 등을 고려하였다. 8개의 보 부재를 제작하여 휨 실험을 수행하였으며 균열 간격, 하중-처짐 관계, 하중-변형률 관계 및 연성지수를 파악하였다. 실험결과는 철근량이 증가함에 따라 균열 개수는 증가하고 균열간격은 감소하는 경향을 나타내며, 콘크리트 강도가 높을수록 균열개수가 줄어들기는 하지만 그 효과는 철근량보다는 상당히 작은 것을 알 수 있었다. 설계기준에서 제안된 평균 균열 간격 식과 비교한 결과, 실험결과가 제안식의 결과보다 약간 크게 나타났으나, 제안식은 콘크리트 강도 및 양생조건을 반영하지 못하는 문제점이 있다. 정상 양생된 부재들의 연성지수는 3.36~6.74이며, 저온 양생된 부재들의 연성지수는 1.51~2.82으로 나타나, 저온 양생된 부재들의 거동은 정상 양생된 부재들에 비해서 연성도지수가 저감됨을 확인하였으며, 본 연구와 기존 연구의 연성지수를 비교한 결과, 고강도 콘크리트 부재의 연성지수는 선행연구의 보통강도 콘크리트의 연성지수 보다 크게 나타났으나, 더 구체적인 결과를 파악하기 위해서는 추가연구가 필요하다고 판단된다.

지상LiDAR를 이용한 터널의 Reverse Engineering (Tunnel Reverse Engineering Using Terrestrial LiDAR)

  • 조형식;손홍규;김종석;이석군
    • 대한토목학회논문집
    • /
    • 제28권6D호
    • /
    • pp.931-936
    • /
    • 2008
  • 지상LiDAR는 토탈스테이션에 비해 신속한 측량이 가능하기 때문에 터널의 내공단면 측량을 적기에 수행하고 중심선 오차와 여 미굴량 발생을 최소화할 수 있는 강점을 가지고 있어 지상LiDAR를 이용한 터널의 내공단면 측량 및 계측이 점점 증대되고 있으며 보다 효율적이고 정확한 지상LiDAR 활용을 위한 연구도 활발하게 진행 중이다. 현재 일반적으로 터널의 여 미굴량을 계산할 때 사용되는 양단면 평균법의 경우 기존 측량 방식인 토탈스테이션 및 사진측량 등과의 비교는 많이 이루어졌으나 터널 전체의 3차원 위치정보를 얻을 수 있는 지상LiDAR를 이용하여 터널의 내공단면을 측량 체적 및 여 미굴량을 구할 때 관측간격에 따른 기준이 없는 실정이다. 이에 본 연구에서는 시험터널에 대한 reverse engineering을 실시하여 터널 내공단면 측량 시 터널단면의 체적을 비교하여 가장 합리적인 간격을 결정하고 이 결과를 토대로 현재 설계 데이터가 존재하지 않는 시험터널에 대한 CAD도면을 제작하였다. 또한 지상LiDAR 기술의 정확도를 검증하기 위하여 토탈스테이션과의 비교를 통하여 타겟좌표 정확도, 입사각에 따른 정확도 분석을 실시하였다.

부산시 좌천동 단열암반층에서 자연구배 추적자시험을 이용한 수리분산특성 연구 (Characteristics of Hydrodynamic Dispersion Using a Natural Gradient Tracer Test in a Fractured Rock at the Jwacheon-dong, Busan City)

  • 정상용;강동환;김병우
    • 지질공학
    • /
    • 제16권3호
    • /
    • pp.245-254
    • /
    • 2006
  • 부산시 좌천동의 단열암반층에서 자연구배 추적자시험으로 브롬이온농도를 관측하여 심도별 단열발달 상태에 따른 수리분산특성을 비교하였으며, 단열암반층의 유효공극율과 종분산지수를 추정하였다. 수직적인 수리분산특성의 차이는 브롬이온의 농도이력곡선, 관측심도별 브롬이온농도와 시간에 대한 선형회귀분석 및 관측지점별 수리단열특성을 이용하여 규명되었다. 관측공 내 지표면하 18 m(RQD 13%, 평균절리간격 2 cm, TCR 100%) 지점이 주입지점에서의 이격거리가 짧고 단열이 더욱 발달되어 있었기 때문에 25 m(RQD 41%, 평균절리간격 7 cm, TCR 100%) 지점보다 추적자가 빨리 도달하였으며, 초기농도와 최고농도가 더 높게 나타났다. 최고농도도달 전후의 농도변화에 의하면 추적자가 최고농도도달시까지는 주로 1차 단열을 통해 이송되었고, 최고농도도달 이후에는 2차 단열을 통해 이송되거나 기질확산에 의한 수리 분산이 진행되었다. 선형회귀분석에 의한 지표면하 18 m 지점에서 브롬이온농도의 증가/감소 기울기는 3.46/-1.57이며 지표면하 25 m 지점에서는 3.19/-0.47로서 파쇄가 더 심한 지표면하 18 m 지점에서의 용질이송이 빠르게 진행됨을 알 수 있었다. 농도이력곡선에서 브롬이온의 농도증가 형태는 가우시안함수로 나타나고, 농도감소 형태는 기질확산에 의한 꼬리효과(tailing effect)로 인해 지수함수로 나타났다. CATTI 코드를 이용하여 추정한 단열암반층의 유효공극율은 10.5%, 종분산지수는 0.85 m이었다.