• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.24-29
• /
• 2001

Adaptive valve timing control is one of the promising techniques to accomplish the optimized mixture formation and combustion depending on the load and speed, which is needed to meet the future challenges in reducing fuel consumption and exhaust emissions. The behavior and the effect of adaptive valve timing control system has been investigated by computer simulation, which simulates the gas dynamics in engines. Improved fuel economy can be achieved by reduction of pumping loss under low and mid load conditions. EIVC(Early Intake Valve Closing) strategy turns out to be superior to LIVC(Late Intake Valve Closing) strategy in reducing fuel consumption. Deterioration of combustion quality can be overcome by introducing LIVO(Late Intake Valve Opening) strategy, which increases turbulent intensity in cylinders. Furthermore, LIVO can reduce HC emission by decreasing the required amount of fuel to be injected during cold start.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.57-64
• /
• 2001

This study presents an self tuning regulator(STR) to improve the air-fuel ratio control of performance of gasoline engine. The STR is designed based on the nonlinear dynamic engine model, and the performance of the STR is evaluated through the simulation and experiments. The STR shows better performance than a conventional PI controller in terms of the response time and disturbance rejection. Since the STR has less calculation load than the complex nonlinear controller, this algorithm can be easily applied to on-board engine controller.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.191-197
• /
• 2004

This paper presents experimental results for human drivers' driving patterns and an Adaptive Cruise Control(ACC) strategy. Analyses have shown that female drivers' driving characteristic values such as time-gap and minimum clearance are larger than those of male drivers'. Human drivers tend to have more clearance margins at high speed than at low speed. At low speed, drivers are much more sensitive to the desired clearance than at high speed. A multi-vehicle detection method is presented to improve ride quality of an ACC. Simulation results have shown that the proposed ACC can provide superior performance compared to the ACC strategy which uses a single-vehicle detection method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.4
• /
• pp.80-86
• /
• 1996

In order to decrease fuel comsumption rate and emissions, lean burn engine which has equipped swirl control valve, is investigated experimentally on the test bench. Single cylinder engine was used to test the combustion and emission performance with 4 kinds of swirl valve. Decrease in the carbon monoxide, hyerocarbon and specific fuel consumption was shown at the lean condition, which means that a good choice of swirl valve on the given intake port geometry can be used to increase the combustion efficiency and lean limit.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.76-84
• /
• 2001

Generally fuel injection system using solenoid have some problems between control signal and mechanical movement like as time lag. Main purpose of the present study is to help the design optimization of GDSI for real engine application. We have adopted two different solenoid driving circuit, namely saturation and pick-hold type and have investigated experimentally the current, needle force, needle opening duration and injection quantity. The pick-hold type driving circuit surpassed a saturation type in the response time and pression control of injection quantity. Accordingly, Using characterization data of operating factors such as time constant, driving force and so on, can be evaluated and adjusted to obtain an optimum injector performance.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.2
• /
• pp.1-12
• /
• 1986

입자상물질을 저감시키는 방법은 크게 두 가지로 나누어진다. 하나는 기관내에서 연소조건을 개 선하여 연소방응시 입자상물질이 가능한한 적게 생성되도록 하는 기관개량(Engine Modification) 방법 즉, 실린더 내에서의 저감기술(In Cylinder Control Techniques)이며, 다른 하나는 기관내에 서 생성된 입자상물질이 대기중에 배출되기 전에 배기관으로부터 직접 제거하는 기술이다. 보통 실린더 내에서의 저감기술이 가장 바람직한 방법으로 지금까지는 이 분야의 기술이 많이 개발 되어 왔으나 디이젤자동차에서 배출되는 입자상물질의 허용기준이 강화됨에 따라 기관 내에서의 저감기술만으로는 목표달성이 어렵기 때문에 그 후처리기술이 필요하게 되었다. 여기서는 최근 까지 연구된 저감장치에 관하여 간단히 소개하고 선진국에서 실제 자동차에 부착사용되고 있거나 가장 효율적이며 사용가능성이 높아 연구되고 있는 입자상물질 필터 및 트랩과 그 재생장치에 대하여 상세히 기술하고자 한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.121-128
• /
• 2000

Simple design methods were developed to control the coolant flow rates through cylinder head gasket holes. Applying the concept of flow through an obstruction the ratio of intake to exhaust side flow rates could be easily controlled while maintaining the flow rates per cylinder of the original model. Flow distribution in the coolant passage of the original model was calculated by CFD and the flow rates at the gasket holes were modified based on the calculation results. The calculated flow rated of the modified gasket holes were reasonably close to target values. For more accurate control of the flow rate distribution, a design method with iterative CFD calculations was also suggested. The final size of gasket holes for the target flow rates were obtained just after a few optimization iterations. These methods can be very useful for the optimization of heat transfer characteristics in engine cylinder head and block.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.49-58
• /
• 1997

In this paper, a transfer function was obtained for a PWM high speed solenoid valve controlled metal belt CVT system. The transfer function was defined as the ratio of speed ratio to PWM duty ratio and derived in time domain by linear regression analysis from the experimental results. The transfer function obtained showed different dynamic characteristics for the up and down shift. Also, LQG/LTR controller was designed for the CVT system using the transfer function. It is seen from the experimental results that LQG/LTR control showed good performance for the speed ratio tracking and disturbance rejection. The phase difference and relatively slow response are considered due to the inaccuracy os the transfer functions, which resulted from the inherent nonlinearities of the transmission characteristics of the metal belt CVT.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.215-221
• /
• 1997

The ability of the engine starting performance of conventional ignition system being currently used in automobile gasoline engine is investigated, and the method of improving is discussed and experimented. The conventional ignition system cannot obtain high ignited voltage because its current is limited by decreasing of terminal voltage of battery at starting the engine also causes irregularity in the starting engine. This paper shows that problem can be improved practically by control of ignition energy properly according to the engine speed, consequently this experimental ignition system can eliminate to remarkable extent the function of the engine starting, and also enhance the performance of the engine at high speed.

• International Journal of Automotive Technology
• /
• v.7 no.2
• /
• pp.187-193
• /
• 2006

When emergency evasion during running is required, a driver sometimes causes a vehicle to drift, that is, a condition in which the rear wheels skid due to rapid steering. Under such conditions, the vehicle enters a very unstable state and often becomes uncontrollable. An unstable state of the vehicle induced by rapid steering was simulated and the effect of differential steering assistance was examined. Results indicate that, in emergency evasion while cornering and during which the vehicle begins to drift, unstable behavior like spins can be avoided by differential steering assistance and both the stability and control of the vehicle is improved remarkably. In addition, reduction of overshoot during spin evasion by the differential steering assistance has been shown to enable the vehicle to return to a state of stability in a short time in emergency evasion during straight-line running. Moreover, the effectiveness of differential steering assistance during emergency evasion was confirmed using a driving simulator.