• Journal of Environmental Science International
• /
• v.12 no.7
• /
• pp.705-713
• /
• 2003

In mid-August 2002, under clear summer pressure patterns, we carried out an intensive meteorological observation to examine the warming effects due to artificial constructions in a large housing complex. We set an automatic weather system(AWS) at two places in a bare soil surface within a limited development district and an asphalt surface within a large apartment residence area, respectively. As a result of observation, it became clear that the difference of the surface air(ground) temperature between the bare soil surface and its peripheral asphalt area reached about 4$^{\circ}C$(13$^{\circ}C$) at the maximum from diurnal variation of surface temperatures on AWS data. Through the heat balance analysis using measurement data, it became clear that the thermal conditions at two places are dependent on the properties of surface material. The latent heat flux over the bare soil surface reached to about 300 W/㎡, which is more than a half of net radiation during the daytime. On the other hand, it was nearly zero over the asphalt surface. Hence, the sensible heat flux over the asphalt surface was far more than that of the bare soil surface. The sensible heat flux over the asphalt surface showed about 20∼30 W/㎡ during the night. It was released from asphalt surface which have far more heat capacity than that of bare soil surface.

• Journal of Environmental Science International
• /
• v.4 no.2
• /
• pp.181-194
• /
• 1995

Flocculation kinetics using ferric nitrate as a coagulant to coagulate kaolin clay in water was examined as a tool to investigate the effect of low temperature under tightly controlled treatment conditions. Both the particle size distribution data obtained from Automatic Image Analysis (AIA) system and the on-line measurement of the degree of turbidity fluctuation in a flowing suspension by Photometric Dispersion Analyzer (PDA) were used to measure flocculation kinetics. Results show that cold water temperature had a pronounced detrimental effect on flocculation kinetics. For improving flocculation kinetics at low water temperature, maintaining constant pOH to adjust water chemistry for temperature changes was found to be partially effective only in the more acidic pH range studied.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.222-229
• /
• 1999

In order to regulate cutting torque in milling, monitoring system should be set to a certain threshold. Radial immersion ratio is an important factor to determine the threshold and should be estimated in process for automatic regulation. In this paper, on-line estimation of the radial immersion ration using spindle motor current in face milling is presented. When a tooth finishes sweeping, a sudden drop of cutting torque occurs. This torque drop is equal to cutting torque acting on a single tooth at the swept angle of cut and can be acquired form cutting torque signals. Average cutting torque per revolution can also be calculate form cutting torque signals. The ratio of cutting torque acting on a single tooth at the swept angle of cut to the average cutting torque per revolution is a function of the swept angle of cut and the number of teeth. Using the magnitude of this ratio, the radial immersion ratio is estimated. Identical algorithm is adopted to estimate the immersion ratio based on the spindle motor current measurement. The experiments performed under different cutting conditions show that the radial immersion ratio can be estimated within 10% error range by the proposed method using spindle motor current.

• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.2
• /
• pp.77-83
• /
• 2014

This paper describes a new technology to develop the character recognition technology based on pattern recognition for non-contacting inspection optical lens slant or precision parts, and including external form state of lens or electronic parts for the performance verification, this development can achieve badness finding. And, establish to existing reflex data because inputting surface badness degree of scratch's standard specification condition directly, and error designed to distinguish from product more than schedule error to badness product by normalcy product within schedule extent after calculate the error comparing actuality measurement reflex data and standard reflex data mutually. Developed system to smallest 1 pixel unit though measuring is possible 1 pixel as $37{\mu}m{\times}37{\mu}m$ ($0.1369{\times}10-4mm^2$) the accuracy to $1.5{\times}10-4mm$ minutely measuring is possible performance verification and trust ability through an experiment prove.

• Journal of Astronomy and Space Sciences
• /
• v.11 no.2
• /
• pp.320-326
• /
• 1994

The KITSAT-1 (Auguse, 1992) and the KITSAT-2(September, 1993) were successfully launched and operated by the SatRec(Satellite Research Center). Both carry the CCD cameras to monitor the image of the earth. We used the camera bench type automatic equipment in the KSRI(Korea Standards Research Institute) to measure the MTF(Modulation Transfer Function) value of the lens attached to the CCD camera. We measured the tangential MTF and the sagital MTF by varing the f-number and the field angle. According to the result, the light from a point source is focused within one pixel of the CCD chip when the f-number is smaller than 4.0, and the MTF value becomes smaller as the field angle increases.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.558-559
• /
• 2018

The harness wiring serves as an intermediary for transmitting the electrical signals necessary to drive the vehicle and is highly influenced by vehicle performance. Wire harness tester performs assembly test. Harness products are operated with the function of checking 0 and 1. Proceed to inspection in wire assembly process. There is a defect in the finished vehicle during use. We want to improve such defects. We design the FPGA and propose the measurement device design and the simulation result that the line and the line are disconnected by ADC precision harness inspection.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.9
• /
• pp.57-66
• /
• 1994

In this paper, we present an iterative learning method of compensating for position sensor error. The previously known compensation algorithms need a special perfect position sensor or a priori information about error sources, while ours does not. to our best knowledge, any iterative learning approach has not been taken for sensor error compensation. Furthermore, our iterativelearning algorithm does not have the drawbacks of the existing interativelearning control theories. To be more specivic, our algorithm learns an uncertain function itself rather than its special time-trajectory and does not reuquest the derivatives of measurement signals. Moreover, it does not require the learning system to start with the same initial condition for all iterations. To illuminate the generality and practical use of our algorithm, we give the rigorous proof for its convergence and some experimental results.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.2
• /
• pp.480-497
• /
• 2012

As a new business concept, machine-to-machine (M2M) communications are born from original telemetry technology with the intrinsic features of automatic data transmissions and measurement from remote sources typically by cable or radio. M2M includes a number of technologies that need to be combined in a compatible manner to enable its deployment over a broad market of consumer electronics. In order to provide better understanding for this emerging concept, the correlations among M2M, wireless sensor networks, cyber-physical systems (CPS), and internet of things are first analyzed in this paper. Then, the basic M2M architecture is introduced and the key elements of the architecture are presented. Furthermore, the progress of global M2M standardization is reviewed, and some representative applications (i.e., smart home, smart grid and health care) are given to show that the M2M technologies are gradually utilized to benefit people's life. Finally, a novel M2M system integrating intelligent road with unmanned vehicle is proposed in the form of CPS, and an example of cyber-transportation systems for improving road safety and efficiency are introduced.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.69-76
• /
• 2013

This paper presents the development of the FCF method for the manufacturing of final products using numbers related to the minimum amount of work. The utilized product is a drum clutch, which is part of the transmission of an automobile. A double acting press is secured first and a prediction of the forming load on the practical material is made through an experiment with a plasticine model. Also, a finite element simulation using product shape and properties is performed, as well as a press experiment. A double acting press is manufactured that is suitable for a double acting experiment with a conventional hydraulic press(200 tons). A peripheral device for the press is additionally designed for experimental purposes. And, the press has as its essential points the drive speed, stroke control, etc., all of which influence the forming and is modified. Especially, a laser system is used for velocity measurement of two punches. The forming load of a practical material is predicted in order to derive a forming load formula for cold conditions on the basis of approximate similarity theory. Finite element analysis of the relative velocity ratio(RVR), etc., for most suitable flow defect(unfilling, etc.) prevention is achieved as well. The results are verified through a press experiment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.57-64
• /
• 2000

In order to regulate cutting torque in milling, monitoring system should be set to a certain threshold. Radial immersion ratio is an important factor to determine the threshold and should be estimated in process for automatic regulation. In this paper, on-line estimation of the radial immersion ratio using spindle motor current in face milling is presented. When a tooth finishes sweeping, a sudden drop of cutting torque occurs. This torque drop is equal to the cutting torque acting on a single tooth at the swept angle of cut and can be acquired from cutting torque signals. Average cutting torque per revolution can also be calculated from cutting torque signals. The ratio of cutting torque acting on a single tooth at the swept angle of cut to the average cutting torque per revolution is a function of the swept angle of cut and the number of teeth. Using the magnitude of this ratio, the radial immersion ratio is estimated. Identical algorithm is adopted to estimate the immersion ratio based on the spindle motor current measurement. The experiments performed under different cutting conditions show that the radial immersion ratio can be estimated within 10% error range by the proposed method using spindle motor current. Varying immersion ratio is also estimated well using the presented algorithm.