• 한국전자파학회논문지
• /
• 제19권11호
• /
• pp.1248-1253
• /
• 2008

본 논문은 접지가 있는 비대칭 CPW(Coplanar Waveguide) 선로를 conformal mapping 방법을 사용하여 해석하였다. 이 방법으로 선로의 준정전계 특성 파라미터인 특성 임피던스와 유효 유전율을 계산하였다. 계산된 결과는 상용 프로그램인 IE3D의 결과와 기존 실험값과 비교했으며, 거의 일치함을 보였다. 그리고 본 논문에 해석한 접지가 있는 비대칭 CPW(MCS: Micro Coplanr Strip) 선로를 이용하여 스텝 임피던스 저역 필터에 적용하였다. 제작된 스텝 임피던스 저역 필터는 일반 마이크로스트립 선로로 구현된 저역 필터 특성과 비교하였다. 제작된 필터의 실험 결과를 모의실험과 비교하여 잘 일치함을 확인하였다.

• Journal of electromagnetic engineering and science
• /
• 제9권3호
• /
• pp.164-173
• /
• 2009

In this paper, two new circuit structures for European and U.S. ultra-wide band(UWB) bandpass filters(BPFs) with sharp roll-off characteristics are introduced. We show first that the ultra-wide bandpass property is obtained from a $\lambda$/4 open T resonator with a capacitively coupled $\lambda$/4 short-circuited line, which provides two attenuation poles at lower and upper cutoff frequencies. Then, two identical capacitively coupled input/output lines, which can be $\lambda$/4-length open ends or $\lambda$/2-length short ends, with the T-resonator, are adopted to suppress lower and higher frequency components outside of the pass band. There is coupling between the input and output lines providing two additional transmission zeros in the lower and upper transition bands of the filter. Since the coupling between the T-resonator with the $\lambda$/4 short-circuited line and the input/output lines limits the bandwidth of the filter to the European UWB band, both the $\lambda$/4 short-circuited line and the input/output lines are inserted between the two stacked T-resonators for the U.S. UWB band. The filter structures are simulated with ADS and HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape which has the dielectric constant of 7.8. Measurement results agree well with HFSS simulation results.

• 한국소음진동공학회논문집
• /
• 제13권8호
• /
• pp.583-590
• /
• 2003

For the preestimate of the vibration level of the ground next to a dwelling, a multivariate statistical analysis on the experiment data acquired from a variety of construction sites was performed, and then a new estimate model for the value of K and n that can be applied in the diagnosis of the damage was offered. The results maybe summarized as follows : First, the $K_{95}$ and n showed high correlation at P$\leq$0.05. Specially the correlation coefficient about $W_{max}$, S were higher in $K_{95}$ than in n. indicating that $K_{95}$ is generally associated with source conditions. Second, the factor analysis permitted to identify two major sources in each fraction. These sources accounted for at least 73 % of valiance of $K_{95}$. Third, the multiple regression model for the estimate of $K_{95}$ was developed from Fac1 which depend upon the source conditions and Fac2 which depend upon the transmission conditions. The n value is able to determine from the correlation relationship associated with $K_{95}$./.

• Nuclear Engineering and Technology
• /
• 제38권1호
• /
• pp.99-108
• /
• 2006

SNU-RCCS is a water pool type RCCS (Reactor Cavity Cooling System) developed for VHTR (Very High Temperature Reactor) application by SNU (Seoul National University). Since radiation heat transfer is the major process of passive heat removal in a RCCS, it is important to determine the precise emissivity of the reactor vessel. Review studies have used a constant emissivity in the passive heat removal analysis, even though the emissivity depends on many factors such as temperature, surface roughness, oxidation level, wavelength, direction, atmosphere conditions, etc. Therefore, information on the emissivity of a given material in a real RCCS is essential in order to properly analyze the radiation heat transfer in a VHTR. The objectives of this study are to develop a method for compensation of the factors affecting the emissivity measurement using an infrared thermometer and to estimate the true emissivity from the measured emissivity via the developed method, especially in the SNU-RCCS environment. From this viewpoint, we investigated factors such as the attenuation effect of the window, filling gas, and the effect of background radiation on the emissivity measurements. The emissivity of the vessel surface of the SNU-RCCS facility was then measured using a sight tube. The background radiation was subsequently removed from the measured emissivity by solving a simultaneous equation. Finally, the calculated emissivity was compared with the measured emissivity in a separate emissivity measurement device, yielding good agreement with the emissivity increase with vessel temperature in a range of 0.82 to 0.88.

• 한국전자파학회논문지
• /
• 제14권9호
• /
• pp.931-935
• /
• 2003

본 논문에서는 LTCC 기술을 이용한 다중기판 2단 LC 대역통과 필터를 제안하였다. 이 필터는 서로 다른 유전율을 갖는 세라믹 재료를 사용하였다. 인덕터는 손실과 기생성분을 감소시키기 위하여 저유전율의 재료에 설계되었다. 반면에 커패시터는 단면적을 감쇄시키기 위하여 고유전율의 재료에 설계되었다. 본 논문에서 제안된 대역통과 필터의 전체크기는 2.5${\times}$2.5${\times}$l.4mm$^3$이며 949 MHz의 중심주파수 및 3.5 dB의 삽입손실과 118MHz의 대역폭을 갖는다. 성능은 각각의 LC 공진기 사이의 커플링 커패시터에 의하여 조절하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.114-117
• /
• 2006

The air filter in engine intake system has a function of filtrating the dirt in the scavenging air as well as attenuating the noise. The noise attenuation within the air cleaner filter, however, has been regarded as negligible by the field engineers. In this paper, for the analysis of the acoustical performance of air filter, an acoustical model was suggested and the characteristics of air filter system were investigated. Fibrous structure of the filter element was modeled as a micro-perforated panel using the flow resistivity and porosity. The pleated geometry of the filter element was modeled as two coupled ducts that have permeable walls, in which each duct area was assumed being constant. Using such simplified geometry, a mathematical model was developed for the sound propagation within a narrow duct system. Visco-thermal effect was considered in modeling the sound propagation through such tubes; the filter box was modeled as a rigid rectangular box. By combining two models, a four-pole transfer matrix was derived. For the validation purpose, transmission loss was measured for a plastic rectangular box containing an air filter. A noticeable effect of the air filter element was observed by including the filter into the box. Comparing the predicted and measured data, we found that the predicted TL agrees well with experimental results, in particular, in magnitude and frequency at TL troughs.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.362-367
• /
• 1987

본 연구에서는 위의 인자들 중 .int.Pdt대신에 계산의 편의상 .int.Pd.theta.로, .DELTA.P는 최고압력차의 영향이 가장 크다고 생각되어 (.DELTA.P)$_{max}$를 대상으로 하여 이들 제인 자와 각 주파수성분과의 상관관계에 대하여 검토하고, 주파수역에 대하여 미치는 영향 을 정량적으로 해석하기 위하여 보조 프로그램을 작성하였다.

• 한국전자파학회논문지
• /
• 제11권8호
• /
• pp.1313-1321
• /
• 2000

본 논문에서는 필터의 설계 및 구현이 용이하고 소형화가 가능한 새로운 구조의 고온초전도 마이크로스트립 형태의 의사 집중상수 소자 공진기를 제안하였다. 또한, 공진기들 사이의 비 인접 결합을 이용하여 notch를 갖는 필터특성의 7-극 대역통과 필터를 설계, 제작하였다. 7-극 notch를 갖는 필터는 두께 0.5mm, 유전율 23.5의 $LaAlO_{3}$ 기판상에 YBCO를 양면 증착하여 제작하였다. 측정결과, 절대 온도 20K에서 중심 주파수 1774MHz 차단대역(cut-off-band)에서 33㏈감쇠를 나타내었다.

• Journal of Biosystems Engineering
• /
• 제14권3호
• /
• pp.168-180
• /
• 1989

This study was attempted to develop the electronic-hydraulic hitch control system for position control of tractor plow and investigate the control performance of the system through experiments. Experiments were carried out to investigate the responses of the system to the step and sinusoidal inputs in position control. The effects of control mode, hydraulic flow rate, reference deadband, and proportional constant on control performance of the system were investigated. The following conclusions were derived from the study; 1. For the position control system operated on on-off control mode, positions of implement were controlled within ${\pm}0.73^{\circ}{\sim}{\pm}1.46^{\circ}$ in rockshaft angle to the reference position when the hydraulic flow rates were 5~15 l/min. For the position control system operated on PWM control mode, positions of implement were controlled within ${\pm}0.73^{\circ}$ to the reference position regardless of hydraulic flow rates. It means that the implement could be positioned more accurately to the reference position on PWM control mode than on on-off control mode. 2. As results of the frequency responses of the position control systems, no clear difference in control performance between on-off control and PWM control modes was found. As the hydraulic flow rates increased, the corner frequencies of amplitude attenuation and phase-angle change increased. It means that the control performance of the system could be improved as the hydraulic flow rate increases.

• Journal of Biosystems Engineering
• /
• 제32권4호
• /
• pp.237-246
• /
• 2007

In this study, the microwave free-space transmission technique was used to measure the dielectric property of powdered food at microwave frequencies. The sample holder was designed and fabricated to transmit the microwave signals ranging from 1 to 15GHz. From the microwave propagation theory the equation expressing the dielectric property of powdered food was derived and validated by standard dielectrics. The dielectric property of powdered food such as wheat flour, coffee powder and milk powder was measured and analyzed. In the uniform range of bulk density of material, the real parts of permittivity of the food samples increased with the increase of moisture content, bulk density and temperature of the samples. The propagation properties such as attenuation and phase shift increased linearly as the moisture density of the food samples increased. As a measuring frequency of the moisture content, the X-band was recommended.