• Title/Summary/Keyword: attached table

Search Result 83, Processing Time 0.029 seconds

A Study on the Application of Friction Pendulum System in Main Control Room of Nuclear Power Plant (마찰진자를 이용한 면진장치의 원전 주 제어실 적용에 관한 연구)

  • Kim, Woo Bum;Lee, Kyung Jin
    • Journal of Korean Society of Steel Construction
    • /
    • v.17 no.4 s.77
    • /
    • pp.407-417
    • /
    • 2005
  • An experimental and analytical study was performed to apply the friction pendulum system (FPS) to the main control room of a nuclear power plant. A friction pendulum bearing was fabricated, and the dynamic response of the bearing was evaluated. A partial model of a main control room attached to the FPS was tested on the shake table. The model consisted of a cabinet, a $3m\times3m$ access floor, and four friction pendulum bearings. The artificial time history based on the floor response spectrum of the main control room was used as the earthquake input signal in the test. Comparisons between the analytical study and the experimental study were conducted to verify the results and to extend the experimental study to the range of parameters that could not be experimentally studied.

Experimental and numerical study on the dynamic behavior of a semi-active impact damper

  • Zheng Lu;Mengyao Zhou;Jiawei Zhang;Zhikuang Huang;Sami F. Masri
    • Smart Structures and Systems
    • /
    • v.31 no.5
    • /
    • pp.455-467
    • /
    • 2023
  • Impact damper is a passive damping system that controls undesirable vibration with mass block impacting with stops fixed to the excited structure, introducing momentum exchange and energy dissipation. However, harmful momentum exchange may occur in the random excitation increasing structural response. Based on the mechanism of impact damping system, a semi-active impact damper (SAID) with controllable impact timing as well as a semi-active control strategy is proposed to enhance the seismic performance of engineering structures in this paper. Comparative experimental studies were conducted to investigate the damping performances of the passive impact damper and SAID. The extreme working conditions for SAID were also discussed and approaches to enhance the damping effect under high-intensity excitations were proposed. A numerical simulation model of SAID attached to a frame structure was established to further explore the damping mechanism. The experimental and numerical results show that the SAID has better control effect than the traditional passive impact damper and can effectively broaden the damping frequency band. The parametric studies illustrate the mass ratio and impact damping ratio of SAID can significantly influence the vibration control effect by affecting the impact force.

An Investigation on Science Teachers' Evaluation Practices in the Secondary Schools (중등학교 과학교사들의 학습 평가에 관한 실태조사)

  • Kim, Ho-Jin;Kwack, Dae-Oh;Sung, Min-Wung
    • Journal of The Korean Association For Science Education
    • /
    • v.20 no.1
    • /
    • pp.101-111
    • /
    • 2000
  • The present study was carried out to investigate the actual condition of the evaluation of science learning in the secondary school, and to develop the basic data for the improvement of the science learning assessment. Various questions for three evaluative domains were asked to 51 science teachers with the questionnaire during the in-service training course for certificate on summer in 1998. The cognition of the table of specification appeared high as 98% responses to the questionnaire, but the teachers' ability to distinguish behavioral elements was low as 47% responses. The evaluative rate of three domains for knowledge, skill and attitude appeared as 45%, 35% and 20% evaluation in both diagnostic and formative evaluation and 40%, 40% and 20% evaluation in summative evaluation. The evaluation of process skill appeared a tendency depending on laboratory reports as 61%, and was higher rather than in the formative evaluation or summative evaluation. In the evaluation of attitude domain, about a half of teachers answered that they evaluated the domain with laboratory reports as 43%, and some teachers evaluated the domain with teacher's observation as 33%. Also there were a few teachers who did not evaluate the attitude domain as 8%. The rate for the elements of the process skill appeared 86% responses in the interpretation of data, 31% in the observative ability, 18% in the predictive ability, 14% in the classified ability, 12% in the measuring and data-investigating ability, 4% in the discussion ability, and 2% in the investigating ability. We could find out that many teachers had given higher rate in the evaluation of process skill and attitude rather than before the present study, therefore there was more improvement in the evaluation for process skill and attitude domain after the 6th curriculum.

  • PDF

The Image Distortion Analysis of Levin-tube tip by Patient position and Incidence Angle when taking Mobile Chest AP Projection (Mobile Chest AP 검사 시 환자자세와 입사각도에 따른 Levin-tube tip의 영상왜곡 분석)

  • Lee, Jinsoo;Park, Hyonghu
    • Journal of the Korean Society of Radiology
    • /
    • v.9 no.7
    • /
    • pp.467-471
    • /
    • 2015
  • This study's purpose is improve image quality to keep accurate tube angle in order to recognize distortion degree conditions by patient's position or tube angle and to provide exact clinical informations when taking chest AP projection for patient which have L-tube in stomach. The experimental equipment was ELMO-T6S by SHIMADZU corporation, then we put L-tube which attached 1 mm gap scales ruler on chest phantom surface. The experiment set by 90 kVp, 4 mAs, 120 cm distance. Each phantom position which changed supine, 30degree, 45degree, 60degree on the table exposured direct, ${\pm}5degree$, ${\pm}10degree$, ${\pm}15degree$ to head and feet directions. As a result, L-tube tip's position was changed by patient's position and tube angle. When patient's position is supine, tip's position change was lower than 30degree, 45degree, 60degree. We have to adjust patient's position or tube angle in order to occur image distortion by fault tube angle when confirming correct position L-tube tip through chest x-ray. Also, Radiological technologist try to make accurate evaluation index for satisfied L-tube insertion.

Participatory Observation Records of the Prof. Sa jin-sil's Academic World (사진실 선생의 학문 세계에 대한 참여 관찰기)

  • Heo, Yong-ho
    • (The) Research of the performance art and culture
    • /
    • no.36
    • /
    • pp.585-602
    • /
    • 2018
  • This article examines the academic world of Professor Sa jin-sil. This article is not a detailed and rigorous assessment of Prof. Sa's work. During my directly or indirectly meeting with Prof. Sa jin-sil, the writing was based on my experiences. This is why the theme of "participatory observation records" is attached. I was aware that this writing would become a customary and formal funeral speech. Because I thought Prof. Sa also did not want formal and customary writing. The initiation of the participatory observational records that I describe was the literature study of Prof. Sa. What I am about to say in the title of the table of "Known Performance and to Revalue." There I summarized my thoughts on what Prof. Sa contributed to the research of the literature study on traditional performance and my opinion of the justice of the assessment of her contributions. I have not recommitted again about contributions or achievements that have already been widely recognized. What I noticed here was what was to be revalued. I once again stressed the achievements that were not properly evaluated despite their importance and significance. In the ensuing discussion, I looked at Prof. Sa's entirely different academic side. I call the passage "an unexpected result against prejudice." The subjects covered were Prof. Sa's field-contextual studies. Prof. Sa is often referred to as a dramatical history or a traditional performing arts scholar who studies literature. Such an idea is so common that it is easy to overlook field-contextual research results, not literature-based. But I think this is prejudice. That is why the title of the table of contents has the words 'unexpected' and 'prejudice'. Here I actively emphasized and evaluated Professor Sa's achievements in field-contextual studies.

Translation of Korean Object Case Markers to Mongolian's Suffixes (한국어 목적격조사의 몽골어 격 어미 번역)

  • Setgelkhuu, Khulan;Shin, Joon Choul;Ock, Cheol Young
    • KIPS Transactions on Software and Data Engineering
    • /
    • v.8 no.2
    • /
    • pp.79-88
    • /
    • 2019
  • Machine translation (MT) system, especially Korean-Mongolian MT system, has recently attracted much attention due to its necessary for the globalization generation. Korean and Mongolian have the same sentence structure SOV and the arbitrarily changing of their words order does not change the meaning of sentences due to postpositional particles. The particles that are attached behind words to indicate their grammatical relationship to the clause or make them more specific in meaning. Hence, the particles play an important role in the translation between Korean and Mongolian. However, one Korean particle can be translated into several Mongolian particles. This is a major issue of the Korean-Mongolian MT systems. In this paper, to address this issue, we propose a method to use the combination of UTagger and a Korean-Mongolian particles table. UTagger is a system that can analyze morphologies, tag POS, and disambiguate homographs for Korean texts. The Korean-Mongolian particles table was manually constructed for matching Korean particles with those of Mongolian. The experiment on the test set extracted from the National Institute of Korean Language's Korean-Mongolian Learner's Dictionary shows that our method achieved the accuracy of 88.38% and it improved the result of using only UTagger by 41.48%.

Derivation of Dynamic Characteristic Values for Multi-degree-of-freedom Frame Structures based on Frequency Response Function(FRF) (주파수응답함수 기반 다자유도 골조 구조물의 동특성치 도출 및 구조모델링 적용 )

  • So-Yeon Kim;Min-Young Kim;Seung-Jae Lee;Kyoung-Kyu Choi
    • Journal of the Korea institute for structural maintenance and inspection
    • /
    • v.27 no.4
    • /
    • pp.1-10
    • /
    • 2023
  • In the seismic design of structures, seismic forces are calculated based on structural models and analysis. In order to accurately address the dynamic characteristics of the actual structure in the structural model, calibration based on actual measurements is required. In this study, a 4-story frame test specimen was manufactured to simulate frame building, accelerometers were attached at each floor, and 1-axis shaking table test was performed. The natural period of the specimen was similar to that of the actual 4 story frame building, and the columns were designed to behave with double-curvature having the infinite stiffness of the horizontal members. To investigate the effects seismic waves characteristics, historical and artificial excitations with various frequencies and acceleration magnitudes were applied. The natural frequencies, damping ratios, and mode shapes were obtained using frequency response functions obtained from dynamic response signals, and the mode vector deviations according to the input seismic waves were verified using the Mode assurance criterion (MAC). In addition, the damping ratios obtained from the vibration tests were applied to the structural model, and the method with refined dynamic characteristics was validated by comparing the analysis results with the experimental data.

Supraclavicular Brachial Plexus block with Arm-Hyperabduction (상지(上肢) 외전위(外轉位)에서 시행(施行)한 쇄골상(鎖骨上) 상완신경총차단(上腕神經叢遮斷))

  • Lim, Keoun;Lim, Hwa-Taek;Kim, Dong-Keoun;Park, Wook;Kim, Sung-Yell;Oh, Hung-Kun
    • The Korean Journal of Pain
    • /
    • v.1 no.2
    • /
    • pp.214-222
    • /
    • 1988
  • With the arm in hyperabduction, we have carried out 525 procedures of supraclavicular brachial plexus block from Aug. 1976 to June 1980, whereas block with the arm in adduction has been customarily performed by other authors. The anesthetic procedure is as follows: 1) The patient lies in the dorsal recumbent position without a pillow under his head or shoulder. His arm is hyperabducted more than a 90 degree angle from his side, and his head is turned to the side opposite from that to be blocked. 2) An "X" is marked at a point 1 cm above the mid clavicle, immediately lateral to the edge of the anterior scalene muscle, and on the palpable portion of the subclavian artery. The area is aseptically prepared and draped. 3) A 22 gauge 3.5cm needle attached to a syringe filled with 2% lidocaine (7~8mg/kg of body weight) and epineprine(1 : 200,000) is inserted caudally toward the second portion of the artery where it crosses the first rib and parallel with the lateral border of the muscle until a paresthesia is obtained. 4) Paresthesia is usually elicited while inserting the needle tip about 1~2 em in depth. If so, the local anesthetic solution is injected after careful aspiration. 5) If no paresthesia is elicited, the needle is withdrawn and redirected in an attempt to elicit paresthesia. 6) If, after several attempts, no paresthesia is obtained, the local anesthetic solution is injected into the perivascular sheath after confirming that the artery is not punctured. 7) Immediately after starting surgery, Valium is injected for sedation by the intravenous route in almost all cases. The age distribution of the cases was from 11 to 80 years. Sex distribution was 476 males and 49 females (Table 1). Operative procedures consisted of 103 open reductions, 114 skin grafts combined with spinal anesthesia in 14, 87 debridements, 75 repairs, i.e. tendon (41), nerve(32), and artery (2), 58 corrections of abnormalities, 27 amputations above the elbow (5), below the elbow (3) and fingers (17), 20 primary closures, 18 incisions and curettages, 2 replantations of cut fingers. respectively (Table 2). Paresthesia was obtained in all cases. Onset of analgesia occured within 5 minutes, starting in the deltoid region in almost all cases. Complete anesthesia of the entire arm appeared within 10 minutes but was delayed 15 to 20 minutes in 5 cases and failed in one case. Thus, our success rate was nearly 100%. The duration of anesthesia after a single injection ranged from $3\frac{1}{2}$ to $4\frac{1}{2}$, hours in 94% of the cases. The operative time ranged from 0.5 to 4 hours in 92.4% of the cases(Table 3). Repeat blocks were carried out in 33 cases when operative times which were more than 4 hours in 22 cases and the others were completed within 4 hours (Table 4). Two patients of the 33 cases, who received microvasular surgery were injected twice with 2% lidocaine 20 ml for a total of $13\frac{1}{2}$ hours. The 157 patients who received surgery on the forearms or hands had pneumatic tourniquets (250 torrs) applied without tourniquet pain. There was no pneumothorax, hematoma or phrenic nerve paralysis in any of the unilateral and 27 bilateral blocks, but there was hoarseness in two, Horner's syndrome in 11 and shivering in 7 cases. No general seizures or other side effects were observed. By 20ml of 60% urcgratin study, we confirm ed the position of the needle tip to be in a safer position when the arm is in hyperabduction than when it is in adduction. And also that the humoral head caused some obstraction of the distal flow of the dye, indicating that less local anesthetic solution would be needed for satisfactory anesthesia. (Fig. 3,4).

  • PDF

An Experimental Study of In-Mold Coating of Automotive Armrests (자동차 암레스트의 인몰드코팅에 관한 실험적 연구)

  • Park, Jong Rak;Lee, Ho Sang
    • Transactions of the Korean Society of Mechanical Engineers A
    • /
    • v.39 no.7
    • /
    • pp.687-692
    • /
    • 2015
  • A mold design for in-mold coating was developed to achieve simultaneous coating and injection molding of an automotive armrest. The developed mold includes one core and two cavities which are composed of a substrate cavity and a coating cavity. The core was attached to a movable plate and two cavities were mounted on a plate sliding in a stationary plate. In a two-step process, the part was first injection molded and subsequently, with the aid of a sliding table, was transferred to a second cavity. The materials used were PC/ABS for substrate and two-component polyurethane for coating. The experiments were conducted by changing the flow rate to investigate mixing characteristics. As the flow rate increased, the mixing improved. Additionally, the bubbles appeared over the substrate surface decreased with an increase of the weight of injected coating material.

A Study on Pressure Distribution for Uniform Polishing of Sapphire Substrate

  • Park, Chul jin;Jeong, Haedo;Lee, Sangjik;Kim, Doyeon;Kim, Hyoungjae
    • Tribology and Lubricants
    • /
    • v.32 no.2
    • /
    • pp.61-66
    • /
    • 2016
  • Total thickness variation (TTV), BOW, and surface roughness are essential characteristics for high quality sapphire substrates. Many researchers have attempted to increase removal rate by controlling the key process parameters like pressure and velocity owing to the high cost of consumables in sapphire chemical mechanical polishing (CMP). In case of the pressure approach, increased pressure owing to higher deviation of pressure over the wafer leads to significant degradation of the TTV. In this study, the authors focused on reducing TTV under the high-pressure conditions. When the production equipment polishes multiple wafers attached on a carrier, higher loads seem to be concentrated around the leading edge of the head; this occurs because of frictional force generated by the combination of table rotation and the height of the gimbal of the polishing head. We believe the skewed pressure distribution during polishing to be the main reason of within-wafer non-uniformity (WIWNU). The insertion of a hub ring between the polishing head and substrate carrier helped reduce the pressure deviation. Adjusting the location of the hub ring enables tuning of the pressure distribution. The results indicated that the position of the hub ring strongly affected the removal profile, which confirmed that the position of the hub ring changes the pressure distribution. Furthermore, we analyzed the deformation of the head via finite element method (FEM) to verify the pressure non-uniformity over the contact area Based on experiment and FEM results, we determined the optimal position of hub ring for achieving uniform polishing of the substrate.