• 대한치과기공학회지
• /
• 제3권1호
• /
• pp.9-16
• /
• 1981

A comparative study was conducted to evaluate the relationship of investing medium to the amount of vertical occlusal changes and to the differences of surface smoothness during denture construction. Three groups of 20 dentures, 30 sets of upper and lower were fabricated of conventional heatcuring acrylic denture base resin, using silicone-gypsum molding techniques, with or without covering the occlusal surfaces of the teeth by artificial stone and all-gypsum molding techniques. The distance between the two reference points indented by 1/2 round bur on the upper and lower frontal surfaces of each articulator were measured and recorded before processing and again after processing and remounting of each denture on the articulator. The differences between the two recordings indicated the amount of vertical opening during denture processing. The difference of surface smoothness were investigated and determined by 3 observers continual comparing of the two randomly selected dentures with each other, which were seperately selected as pairs from the different two groups of 20. The results obtained were as follows: 1. During resin processing no statistically significant differences of the amount of vertical occlusal changes were detected between any of the two groups of two silicone-gypsum and one allgypsum molding techniques, although the amount of vertical opening was somewhat increased when silicone-gypsum molding technique was used. 2. Surface smoothness of the processed denture was makedly by increased when silicone-gypsum molding technique was used.

• 한국환경복원기술학회지
• /
• 제11권2호
• /
• pp.40-54
• /
• 2008

Small and large dams are installed in the course of a stream for maintaining the water level of the stream or obtaining agricultural water. Currently about 18,000 of them are installed in Korea to supply water. However, the environmental problems of small dams are well known : the interruption of stream eco-corridors, deterioration of water quality in the upper reaches of the small dam, changes in the habitats of riparian organisms, damages to the stream scenery. In a very few of these small dams artificial eco-corridors like fishways are installed, but the number is very minimal.Accordingly, to efficiently restore stream eco-corridors by removing these small dams, it will be necessary to closely examine physical impacts, such as changes in the riverbed and changes in the shape of the stream caused by the removal, chemical impacts, such as changes in water quality, and transport and accumulation of contaminated sediments and biological impacts, such as changes in the habitats of organisms, and develop related technologies in advance, and have these technologies verified through demonstration application in the sites. In this study, we analyzed the physical, chemical and ecological impacts of the removal of the above-mentioned small dams, and conducted a research on the demonstration small dam removal project for a spot investigation. As a result, the small dam removal will restore the eco-corridor, there by improving the habitat of fishes and crustaceans. The number of major underwater organisms inhabiting the Gokreungcheon, such as Korean spotted sleepers, Chinese minnows, Microphysogobio yaluensis, Abbottina rivularis, stone morokos, striped shinners, long-nosed barbels, and Chinese mitten crabs, is expected to increase, and the food chain in the ecosystem will improve so that species diversity will improve as well.

• The Journal of Advanced Prosthodontics
• /
• 제5권3호
• /
• pp.219-225
• /
• 2013

PURPOSE. Few studies have investigated the marginal accuracy of 3-unit zirconia fixed partial dentures (FPDs) fabricated by computer-aided design/computer-aided manufacturing (CAD/CAM) system. The purpose of this study was to compare the marginal fit of zirconia FPDs made using two CAD/CAM systems with that of metal-ceramic FPDs. MATERIALS AND METHODS. Artificial resin maxillary central and lateral incisors were prepared for 3-unit FPDs and fixed in yellow stone. This model was duplicated to epoxy resin die. On the resin die, 15 three-unit FPDs were fabricated per group (45 in total): Group A, zirconia 3-unit FPDs made with the Everest system; Group B, zirconia 3-unit FPDs made with the Lava system; and Group C, metal-ceramic 3-unit FPDs. They were cemented to resin dies with resin cement. After removal of pontic, each retainer was separated and observed under a microscope (Presize 440C). Marginal gaps of experimental groups were analyzed using one-way ANOVA and Duncan test. RESULTS. Mean marginal gaps of 3-unit FPDs were $60.46{\mu}m$ for the Everest group, $78.71{\mu}m$ for the Lava group, and $81.32{\mu}m$ for the metal-ceramic group. The Everest group demonstrated significantly smaller marginal gap than the Lava and the metal-ceramic groups (P<.05). The marginal gap did not significantly differ between the Lava and the metal-ceramic groups (P>.05). CONCLUSION. The marginal gaps of anterior 3-unit zirconia FPD differed according to CAD/CAM systems, but still fell within clinically acceptable ranges compared with conventional metal-ceramic restoration.

• 대한치과기공학회지
• /
• 제39권1호
• /
• pp.25-33
• /
• 2017

Purpose: The aim of this study was to evaluate accuracy of glass fiber mesh complete denture of before and after curing. Methods: Edentulous model was selected as the master model. Ten study models were made by Type IV stone. Wax complete dentures were produced by the denture base and artificial teeth. CD and GD groups were measured six measurement distance before curing. The wax complete denture was investment after measurement is completed. Using a heat polymerization resin was injected resin. After injecting the resin it was curing. A complete denture was re-measured after curing. The measured data was verified by paired t-test. Results: Overall CD group was larger the value of the measured length. In the CD group, A-D point was larger. The smallest point was the B-D point. However, there was no statistically significant difference only C-D point(p>0.05). In the GD group, A-B point was larger. but B-D point was the smallest. A-D and B-C statistically points showed significant differences(p<0.05). Conclusion: Glass fiber mesh resin complete denture can be clinically applied to the edentulous patient.

• 한국주거학회논문집
• /
• 제19권6호
• /
• pp.157-166
• /
• 2008

Until 1960, the major housing type of rural area in Korea was traditional wooden frame building, which was made of natural materials. In the course of modernization and New Village Movement, most of traditional houses have been renovated focusing on changing roof material of rice straw into slate, keeping existing main wooden structure. And then from around 1980, by economical development the new houses have been constructed. On these three phases of traditional type, remodeling type and new construction type, the natural materials of housing facade as wood, soil, stone and plant changed into artificial materials as cement, chemical material and paint. At the same time the exterior color of housing also have been changed and varied. The purpose of this thesis is to find out the changing aspect of exterior color by comparing remodeled and new constructed housing with of traditional housing. The exterior color of one hundred and fifty seven houses were surveyed and the three color attributes of each part of facade, as roof, wall and window, were analyzed and compared. In case of traditional houses, 98.3% of color are concentrated on the warm color of Y and YR on HUE scale, and 88% of their color are low Chroma. And Value of their color has been varied and spreaded from low to high Value scale. From traditional types to remodeled and new constructed houses, the concentration ratio of warm color on Hue scale reduced from 98.3% to 68.7% and ratio of low Chroma was also changed from 88% to 73.2% and the ratio of low Value color reduced from 51.9% to 29.7%. The exterior color of houses in rural area varied on Hue, and the more saturated colors were used and they became brighter compared with color of traditional houses. It is expected that the results of this study can be used for basic data of exterior color planning and improvement into harmonized color with natural environment.

• Spatial Information Research
• /
• 제14권3호
• /
• pp.285-297
• /
• 2006

본 연구는 지라정보시스템과 원격탐사자료를 이용한 거시적 관찰과 현지답사를 통해 조선시대의 왕릉 분포지에 대해 형태적 특성과 외부 환경적 특성을 분석한 것이다. 조선시대 왕릉은 주로 호상편마암과 화강암 지질에 위치하며, 봉분은 남사면과 동사면에 주로 위치한다. 해발고도는 150미터에서 200미터 사이에 분포한다. 논리적인 풍수이론을 검증한 결과라기 보단 위성영상에 나타날 왕릉을 분석하여 현재 시점에서 입지를 관찰하게 되어 정확한 입지 요인을 도출하기는 한계가 있었다. 배산임수의 임(臨)이 얼마나 가까워야 하는지를 수량화 하는 것 자체가 매우 어려운 작업이고 지리정보분석의 결과로 평균 600미터 정도 떨어져 있는 하천은 의미가 없을 수 있다. 또한 광릉의 경우에서 보듯 상세한 지형지물의 관찰의 결과 왕릉은 인위적 훼손과 자연적 풍화와 침식에 오랫동안 노출되고 있었다. 사면분석과 경사분석 등의 지리정보 분석과 더불어 야외조사를 통해 지형형성과정을 관찰한 내용은 왕릉의 관리와 복원에 사용될 것이다.

• 지구물리
• /
• 제6권4호
• /
• pp.277-294
• /
• 2003

구조물의 시간경과에 따른 변형 및 성능저하 현상은 인위적 요인 및 시간경과에 따른 지반상태의 변화 혹은 지반 변위요인의 누적에 의해 발생한다 본 연구에서는 경상남도 경주시에 위치한 첨성대를 연구대상으로 설정하였다. 첨성대는 약 1,300여 년 전 건립된 석축구조물로서 지반침하로 약간 기울어져 있으며 일부 석재 사이의 틈이 벌어져 있는 상태이다 본질적인 대책수립을 위하여 본 연구에서는 이러한 목적을 위하여 차원 레이저스캐닝시스템에 의한 형상 역공학적 연구 물리탐사에 의한 지반공학적 특성 연구 및 고유진동수 측정에 의한 첨성대의 동적특성 등의 다음과 같은 연구들을 수행하였다 첫째 정밀측량에 의한 첨성대의 정밀한 변형량 측정 및 지속적인 변위측정을 위하여 차원 레이저 스캐닝에 의한 첨성대의 차원 공간위치정보를 취득하여 형상역공학에 의한 차원 벡터 이미지 형상구현 및 첨성대의 크기 변위량 변위방향 등 여러 가지 제원을 구하고자 하였다 둘째 다양한 비파괴적 물리탐사 방법들을 적용하여 첨성대 및 주변 지반의 물성분포 및 지반특성을 파악하고자 하였다 한편 다양한 물리탐사를 통하여 향후 유사한 조사에 있어서 적절한 물리탐사 방법을 제시하고자 하였다 셋째 경주 첨성대의 1/10모형에 대한 동적특성실험 및 실물에 대한 고유진동수 측정을 통해 첨성대의 구조적 특성을 연구하여 첨성대의 구조특성 및 상태판단 및 동적특성 파악에 의한 내진성능을 판단하고자 하였다.

• 건축역사연구
• /
• 제19권6호
• /
• pp.233-250
• /
• 2010

Jukseoru as an official pavilion of the government, one of the eight sceneries in Gwndong Area, is located on the cliff over Osipcheon River. This paper interprets form and space of the pavilion with restored old life by analyzing pictures of official party in 18th century in Chosun Dynasty. Every part of the space is occupied by persons by the class and duty: the pricipal guest, nobles, subordinates, gisaengs, court musicians, and guards from the high to the low and from the inside to the outside. Applying the analysis to the Jukseoru pavilion, the noblest lord takes sit on the platform in front of folded screen at main bay under checked ceiling, enclosed by low timber beam. The next northern end bay is a place for subordinates' and servants' waiting for preparation for rice wine. Southern end entrance bay is not a result of later addition but deliberately and originally made for lower place outside the railing of wooden floor: for a waiting woman gisaeng, and subordinates. Outside under the eaves on the platform with bedrock, artificial stone and soil is a place for court musicians, subordinates, and guards. The yard in front of the building is a place for preparing meals by cookers. Every detailed ornamental form is different each other by the place for the occupied class. Existing theory tells that the building, 7 bays gable-and-hipped roof, is a result of structural extention of 2 bays at the 5 bays gabled-roof. However, through the interpretation of old pictures and application to the pavilion, the present Juseoru is not a result of later structural addition, but deliberately designed creation suited to life in hierarchical traditional society.

• 대한치과보철학회지
• /
• 제18권1호
• /
• pp.37-47
• /
• 1980

The purpose of this study was to investigate the stresses in different proximal margins and to measure, quantitatively, the effect of different modifications in the design of preparations on the stresses using two-dimensional photoelasticity. Photoelastic stress analysis is based on the phenomenon, exhibited by most transparent solids, of becoming birefringent, or doubly refracting, when strained. Two birefringent materials were used in this study, PSM-1 and PSM-5 in .standard sheet ($10'{\times}10'{\times}\frac{1}{4}'$ thickness), PSM-1(polyester) was used for constructing the substructure, and PSM-5(epoxy resin) was used in making the restorations to be investigated. Two birefringent materials were used in the construction of composite photoelastic model. Seven variable models were constructed. The peripheral dimensions of all model were constant and the models represent an occlusomesial section of a lower posterior molar. Model 1 represents the knife edge margin (shoulderless), Model 2 represents the chamfer, Model 3 represents a rounded shoulder(no sharp angle between the axial wall and gingival floor), Model 4 represents a flat shoulder (axial wall is a $90^{\circ}$ angle to the gingival wall), Model 5 represents $+15^{\circ}$ angulation, Model 6 has a $-15^{\circ}$ angulation, and Model 7 is the same as Model 4 except that it has a $45^{\circ}$ bevel. Improved artificial stone was used to represent dental cement in luting the composite photoelastic model. Static loading procedures(100 pounds) were used at preplanned sites. The results were as follows; 1. The stresses in the proximal portion of all tested models were compressive in nature when the proximal shoulders were loaded vertically on the same proximal marginal ridge. 2. The round and chamfered preparations were the optimum designs in proximoocclusal restorations. They showed the lowest stress concentration factor, i.e. 2.16 and 2.23, respectively. The knife edged shoulder had the highest value, K=5.39. Round type shoulder geometry experiments reduced the stress concentration factor (S.C.F.) 3. The gingival portion of proximal shoulder geometry was a critical location for stress concentration.

• 구강회복응용과학지
• /
• 제19권3호
• /
• pp.153-168
• /
• 2003

It is very important to arrange the artificial teeth correctly in bucco-lingual (labio- lingual) relation in reconstrcting dentition. Although many anatomic landmarks and techniques have been reported over the years, they are based on westerns. So this study was performd to examine the horizontal relations of mandibular teeth in Korean dentulous adults. 200 volunteers(mean age 22.9) who had natural dentition were selected. The impressions were taken with irreversible hydrocolloid impression material and mandibular study models were fabricated using class I dental stone. Then they were measured with 3-dimensional measuring device specially designed for this study. The results were as follows ; It is better to consider the lingual cusps of the lower posterior teeth as a guide than the linguoaxial surfaces of the lower posterior teeth, arranging the lower posterior teeth buccally to the line which starts from the mesial aspect of the lower canine and continue backward to the lingual aspect of the retromolar pad. It is better to arrange the fossae of the lower posterior teeth buccally to the line which starts from the cusp tip of the lower canine and continue backward to the top of the retromolar pad. The positions of the lower posterior teeth in the denture-bearing area ; considering the fossa as a guide, the 2nd premolar was positioned in center. considering the buccal cusp as a guide, the 1st molar and the 2nd molar were positioned in center. the distance ratio(d/a) was incresed constantly from the lower canine to the 2nd molar d ; the distance between the buccal vestibule(the lowest point) and the buccal cusp tips of the lower posterior teeth. a ; the distance between the buccal vestibule(the lowest point) and the lingual vestibule(the lowest point). The lower canine was positioned lingually($0.11{\pm}0.13$) than the labial vestibule, and the central incisor and the lateral incisor were positioned almost in the imaginary perpendicular plane of the labial vestibule(the lowest point).