• Korean Journal of Materials Research
• /
• v.33 no.12
• /
• pp.565-571
• /
• 2023

AA1050/AA6061/AA1050 layered sheet was fabricated by cold roll-bonding process and subsequently T4 and T6 aging-treated. Two commercial AA1050 sheets of 1 mm thickness and one AA6061 sheet of 2 mm thickness were stacked up so that an AA6061 sheet was located between two AA1050 sheets. After surface treatments such as degreasing and wire brushing, they were then roll-bonded to a thickness of 2 mm by cold rolling. The roll-bonded Al sheets were then processed by natural aging (T4) and artificial aging (T6) treatments. The as roll-bonded Al sheets showed a typical deformation structure, where the grains are elongated in the rolling direction. However, after the T4 and T6 aging treatments, the Al sheets had a recrystallized structure consisting of coarse grains in both the AA5052 and AA6061 regions with different grain sizes in each. In addition, the sheets showed an inhomogeneous hardness distribution in the thickness direction, with higher hardness in AA6061 than in AA1050 after the T4 and T6 age treatments. The tensile strength of the T6-treated specimen was higher than that of the T4-treated one. However, the strength-ductility balance was much better in the T4-treated specimen than the T6-treated one. The tensile properties of the Al sheets fabricated in the present study were compared with those in a previous study.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.281-284
• /
• 2003

The microstructural changes of Al-Zn-Mg-Cu alloy containing Sc during hot extrusion and post heat treatment is investigated. Two kinds of Al-Sc alloys with different alloying elements (B1, B2) are hot extruded to make I-shape bars at 380$^{\circ}C$, then the bars are solution treated at 480$^{\circ}C$ for 2hrs followed by artificial aging at 120$^{\circ}C$ for 24hrs. The interior microstructure of as extruded bar consists of elongated grains, however, fine equiaxed grains are mainly observed around surface. The microstructural gradient suggests that different restoration process can proceed during the hot extrusion. For B1 and B2, different grain growth behaviors are found around the surface during the post heat treatment. Rapid grain growth behavior around the surface is discussed related with the crystallographic orientation of the grain.

• Korean Journal of Materials Research
• /
• v.26 no.7
• /
• pp.388-392
• /
• 2016

A cold roll-bonding process was applied to fabricate an AA1050/AA6061/AA1050 laminate complex sheet. Two AA1050 and one AA6061 sheets of 2 mm thickness, 40 mm width and 300 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 1.2 mm in thickness by conventional rolling. The rolling was performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 5.0 m/sec. The AA1050/AA6061/AA1050 laminate complex sheet fabricated by roll bonding was then hardened by natural aging T4) and artificial aging (T6) treatments. The microstructures of the as-roll bonded and the age hardened Al complex sheets were revealed by optical microscope observation; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the as-roll bonded complex sheet was found to increase by 2.9 times compared to that value of the starting material. In addition, the hardness of the complex sheets increased with cold rolling for AA1050 and age-hardening treatment for AA6061, respectively. After heat treatment, both AA1050 and AA6061 showed typical recrystallization structures in which the grains were equiaxed; however, the grain size was smaller in AA6061 than in AA1050.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.1
• /
• pp.59-65
• /
• 2006

The impermeable seed coat is valuable trait in soybean because impermeable seed retain viability for longer period than permeable seed under adverse conditions such as delayed harvest or prolonged storage. Soybean seeds of various size showing different seed hardness were examined for their water absorption and seed viability under adverse storage conditions. Of one hundred thirty nine genotypes, eight types of seeds having different seed hardness and seed size were used as material. Soybean genotypes showing high hard seed rate, GSI13125 (89%), GSI10715 (54%), and GSI10284 (42%), were slow in water absorption and low in the electroconductivity of seed leachate in distilled water. Germination of GSI10284 and GSI13125 that have higher hard seed rate was less affected by CSVT and artificial aging treatment indicating higher seed storability. The higher storing ability of both collections was confirmed by electroconductivity test for leachate. GSI10122 showed low seedling emergence when the seeds were artificially aged. This genotype was considered as to having a poor storing ability based on difference of electroconductivity before and after artificial aging. Among tests conducted in the experiment, CSVT could be used for determining storage life in legumes. In conclusion, water absorption property of seed was strongly related to the hardness that is directly related to the seed viability and storing ability in soybean seed.

• Korean Journal of Materials Research
• /
• v.30 no.8
• /
• pp.435-440
• /
• 2020

The relationship between the precipitation of secondary phase and the thermal properties of Al-4.5%Cu alloy (in wt.%) after various heat treatments has been studied. Solid solution treatment of alloy was performed at 808 K for 6 hours, followed by warm water quenching; then, the samples were aged in air at 473 K for different times. The thermal diffusivity of the Al-4.5%Cu alloy changed with the heat treatment conditions of the alloy at temperatures below 523 K. The as-quenched specimen had the lowest thermal diffusivity, and as the artificial aging time increased, the thermal diffusivity of the specimen increased in the temperature range between 298 and 523 K. For the specimen aged for five hours, the thermal conductivity was 12% higher than that of the as-quenched specimens at 298 K. It is confirmed that the thermal diffusivity and thermal conductivity of the Al-4.5%Cu alloy significantly depend on their thermal history at temperatures below 523 K. The precipitation and dissolution of the Al₂Cu phase were confirmed via DSC for the alloys, and the formation of coefficient of thermal expansion peaks in TMA was caused by precipitation. The precipitation of supersaturated solid solution of Al-4.5%Cu alloys had an additional linear expansion of ≈ 0.05 % at 643 K during thermal expansion measurement.

• Journal of East-West Nursing Research
• /
• v.28 no.2
• /
• pp.100-108
• /
• 2022

Korean medicine has traditionally provided a lot of medical care for the treatment of infertility. The combination treatment of Korean medicine and Western medicine can be effective for infertility to improve the problems caused by the extremely low fertility rate and the aging of pregnant women. In relation to female infertility, we reviewed the evidence for Korean medicine treatment for polycystic ovary syndrome, which has recently been increasing interest in female infertility, and the evidence for the collaboration between Korean and Western medicine in the treatment of polycystic ovary syndrome and infertility. Because polycystic ovary syndrome is closely related to metabolic diseases related to endocrine abnormalities, hormone treatment alone has limited therapeutic effects and has side effects. In domestic and international research, herbal medicine and acupuncture in the treatment of infertility have shown good clinical effects based on the hypothesis of various mechanisms of effect, and many cases of successful pregnancy have been reported. Although continuous research through large-scale randomized clinical studies is needed to prove efficacy, the importance of combined treatment of Korean medicine and Western medicine in infertility treatment is increasing in order to solve the extremely low fertility rate. Combining artificial insemination or in vitro fertilization with Korean medicine treatment is highly likely to be effective in increasing pregnancy success and fertility rates. In women with polycystic ovary syndrome, which is recognized as a metabolic disease due to endocrine abnormalities among the causes of female infertility, Korean medicine treatment can increase the pregnancy rate with herbal medicines and acupuncture, etc. Although well-designed large-scale clinical studies are currently lacking and meta-analysis has not provided sufficient evidence, the combination treatment of Korean medicine and Western medicine is more active to increase the pregnancy rate for solving the problem of low fertility.

• Journal of Welding and Joining
• /
• v.21 no.1
• /
• pp.99-106
• /
• 2003

This research was aimed to evaluate the material degradation with various microstructures of X20CrMoV121 steel weldment by Advanced Small Punch(ASP) test. Due to the regional limitation on constitutive structures, the minimized loading ball(${\varphi}1.5mm$) and bore diameter of lower die(${\varphi}3mm$) were designed for the ASP test. The micro-hardness test was also performed to assess the mechanical properties with artificial aging heat treatment. Material degradation was estimated by ductile-brittle transition temperature(DBTT). The results obtained from the ASP test were compared with those from conventional small punch(CSP) test and CVN impact test for several weldment microstructures. It was found that the ASP test clearly showed the microstructural dependance on the material degradation in the weldment.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.53-58
• /
• 2004

The microstructural changes of Al-Zn-Mg-Cu alloy containing Sc during hot extrusion and post heat treatment were investigated. Two kinds of Al-Sc alloys with different alloying elements (B1, B2) were hot extruded to make T-shape bars at extrusion temperature of $380^{\circ}C$, then the bars were solution treated at $480^{\circ}C$ for 2hrs followed by artificial aging at $120^{\circ}C$ for 24hrs. The interior microstructure of as extruded bar consisted of elongated grains, however, fine equiaxed grains were also observed around surface. The microstructural gradient suggested that different restoration process could proceed during the hot extrusion. For B1 and B2, different grain growth behaviors were found around the surface during the post heat treatment. Rapid grain growth behavior was observed for B1 around the surface, however, it was not observed for B2. Orientation pinning, which was related with the evolution of preferred orientation, and precipitation were thought to be responsible for the rapid grain growth.

• Journal of Biosystems Engineering
• /
• v.40 no.3
• /
• pp.224-231
• /
• 2015

Purpose: Corn is a major commercial crop targeted for genetic modification owing to its high consumer demand as a foodstuff for humans and livestock, as well as its other industrial applications. However, the safety of genetically modified (GM) crops is controversial. Indeed, several countries have banned the importation of GM seeds that can germinate. Therefore, development of effective, convenient, and nondestructive methods to inhibit seed germination is required. Methods: This study aimed to examine the efficacy of microwave heat treatment for inhibition of germination of corn kernels and for optimization of power and exposure time required for effective aging treatment. Artificial inhibition was induced in corn kernels using microwave heat treatment. Seven power levels were examined (400, 500, 600, 700, 800, 900, and 1000 W) at each of the four exposure times (0.5, 1.0, 1.5, and 2.0 min). Results: Corn kernels could be aged effectively after heating for 0.5~1.0 min at powers greater than 800 W, with increasing efficacy observed at higher powers. Further analysis showed that the most effective inhibition of germination was observed at 1000 W for 40 s. This setting did not cause any physical damage to the corn kernels. Conclusions: Optimal inhibition of corn kernel germination was achieved using higher power for shorter times, which may be useful for industrial corn seed treatment.

• Korean Journal of Metals and Materials
• /
• v.46 no.4
• /
• pp.209-216
• /
• 2008

Super austenitic stainless steels shows the high PRE (Pitting Resistance Equivalent) number and the good corrosion resistance. This work controlled the Co contents in Fe-31Cr-1.7Mo-27Ni-0.25N alloys to elucidate the effect of cobalt contents on the biocompatibility and corrosion resistance. Increasing Co contents, the hardness of the annealed alloys tends to be reduced. In aged alloys, cobalt decreased the increments of hardness by aging treatment. Cobalt decreased the critical pitting temperature (CPT) in 6% $FeCl_3$ + 1% HCl solution, but improved the anodic polarization behavior in Hanks' balanced salt solution and artificial saliva solution. Repassivation rate in artificial body solutions was improved by increasing cobalt contents, but didn't show the linear relationship to PRE number of the alloys. The experimental alloys showed the non-cytotoxicity because of its high corrosion resistance.