• Journal of the Korea Concrete Institute
• /
• v.27 no.5
• /
• pp.521-530
• /
• 2015

Design of fiber reinforced ultra-high strength concrete members should be verified with analytical or experimental methods for safety. Members with compressive strength larger than limitation of current design code usually be designed with analytical verification using stress-strain relation of concrete and reinforcements. For this purpose, mechanical characteristics of steel fiber reinforced ultra-high strength concrete were defined under uniaxial compression. Mix proportions of test specimens were based on reactive powder concrete and straight steel fibers were mixed with different volume fraction. Compressive strength of matrix were distributed from 80 MPa to 200 MPa. Effect of fiber inclusion were investigated : increase of compressive strength of concrete, elastic modulus and strain corresponding to peak stress. For the wide range application of investigation, previously tested test specimens were collected and used for investigation and estimation equation. Based on the investigation and evaluation of previous research results and estimation equation of mechanical characteristics of concrete, regression equations were suggested.

• Korean Journal of Construction Engineering and Management
• /
• v.15 no.1
• /
• pp.87-100
• /
• 2014

Environmental problems and the shortage of natural resources are currently gathering more attention in Korea and international countries. With these problems, it is reported that most current domestic buildings are emitting approximately 138 million tons of greenhouse gas. According to a recent report from the investigation of Korean housing population, the total number of households is approximately 12.9 millions, and the apartments that were built more than 15 years ago amounted to 3.1 millions. This shows that the rates of old apartment housings are increasing. Therefore, it is necessary to consider the deteriorated facilities and environmental improvement. Also, the construction industry is benefited by improving these housings which may need either remodeling or reconstruction. Environmental friendly buildings are a rising consideration for remodeling and reconstruction projects; it helps to determine many business matters in construction. The main purpose of this research is to improve environmental condition in apartments with comparison analysis between remodeling and reconstruction alternatives. This research is focused on characteristics of remodeling and reconstruction and it sets up the same condition with each level in order to evaluate the value of environmental friendliness and analyze its definition. The result of this research provides a unique emitting rate at a novel framework and this will cause the reduction of $CO_2$. It is analyzed that the remodeling construction can reduce the great amount of $CO_2$. Therefore, it will be a good decision guideline in selecting the most eco-friendly alternative to improve environment for building construction. Although reconstruction is a popular alternative nowadays in Korea, this research can provide a reason why decision makers should put more emphasis on remodeling as an environment-friendly alternative.

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.515-525
• /
• 2007

In this investigation, results of laboratory tests on four reinforced concrete flat plate interior connections with elongated rectangular column support which has been used widely in tall residential buildings are presented. The purpose of this study is to evaluate an effect of column aspect ratio (${\beta}_c={c_1}/{c_2}$=side length ratio of column section in the direction of lateral loading $(c_1)$ to the direction of perpendicular to $c_1$) on the hysteretic behavior under earthquake type loading. The aspect ratio of column section was taken as $0.5{\sim}3\;(c_1/c_2=1/2,\;1/1,\;2/1,\;3/1)$ and the column perimeter was held constant at 1200mm in order to achieve nominal vertical shear strength $(V_c)$ uniformly. Other design parameters such as flexural reinforcement ratio $(\rho)$ of the slab and concrete strength$(f_{ck})$ was kept constant as ${\rho}=1.0%$ and $f_{ck}=40MPa$, respectively. Gravity shear load $(V_g)$ was applied by 30 percent of nominal vertical shear strength $(0.3V_o)$ of the specimen. Experimental observations on punching failure pattern, peak lateral-load and story drift ratio at punching failure, stiffness degradation and energy dissipation in the hysteresis loop, and steel and concrete strain distributions near the column support were examined and discussed in accordance with different column aspect ratio. Eccentric shear stress model of ACI 318-05 was evaluated with experimental results. A fraction of transferring moment by shear and flexure in the design code was analyzed based on the test results.

• Korean Journal of Heritage: History & Science
• /
• v.50 no.4
• /
• pp.82-103
• /
• 2017

Systems operating construction expenses for preservation and repair of the architectural heritage may be divided into two in the Japanese colonial era. They are preservation cost nd preservation cost-aided constructions, according to the ownership of a building. Preservation cost construction refers to preservation and repair of government-owned buildings that Japanese Government General of Korea had the ownership and the right of management, and preservation cost-aided construction means preservation and repair of private buildings such as Buddhist temples. In the case of preservation and repair of buildings owned by the government, it was done by the Japanese Government General of Korea, so the same agent executed the budget and managed the properties. They included royal tombs and relics, old government offices, Hyanggyo and some Seowon. On the other hand, in the case of preservation and repair of private buildings, they were private properties, so Japanese Government General of Korea had rights only for permission of preservation and repair. If there was a request for .preservation and repair by an owner, the Japanese Government General of Korea decided on whether it would support its expenses or not and played a role of management and supervision. It applied to Buddhist shrines and pagodas owned by Buddhist temples and shrines and temples owned by individuals and families. Hence, in the case of government-owned buildings, because the preservation cost was spent from the Japanese Government General of Korea's budget for investigation expenses of historical remains or repair expenses of Jeolleung and ruins, they were classified into preservation cost constructions. As for private buildings, the cost was spent from their budget for aiding preservation expenses, so they were classified into preservation cost-aided constructions. Because preservation cost construction and preservation cost-aided construction were conducted by two different agents, there were a little difference in procedures for executing a construction. There was no big difference in the general progress of constructions but was an administrative difference in the kinds of documents submitted and the roles of field supervisors. Such dual systems remained unimproved throughout the Japanese colonial era. The Japanese Government General of Korea was the colonial government so much influenced by the Japanese Government. Most Japanese architectural heritage was owned by Buddhist temples and Shinto shrines and there was almost no building owned by the government, resulting in a unitary system unlike Korea. Heritage system by the Japanese Government General of Korea was established under the influence of Japan regardless of the situation in Korea. Accordingly, Japanese Government General of Korea could not present a definite solution in the bisected system of preservation and repair expenses for the heritage. It shows the limits of the Japanese Government General of Korea in the colonial era.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.11
• /
• pp.5-13
• /
• 2015

For the bearing capacity evaluation, dynamic pile tests instead of static pile tests have been commonly used in embedded piles, which are known to have low noise and low vibration construction method. The objective of this study is to analyze the bearing capacity and penetration behaviors of embedded piles, which are constructed in different ground conditions, by using force and velocity signals obtained in the final blows during construction of embedded piles. For the dynamic pile analyses, the CAse Pile Wave Analysis Program (CAPWAP) and Wave Equation Analysis of Piles (WEAP) have been commonly used. In this study, the CAPWAP and WEAP are used for the analyses of the dynamic pile tests, which are conducted on embedded piles. The input values, output values, and force-velocity graphs of CAPWAP determined by analyzing the measured force-velocity signals are investigated. In addition, similar force-velocity singals are obtained from the WEAP by analyzing the input values of the WEAP. Considering the subsurface investigation results around the pile tips, if the N-value increases exponentially along the depth, toe quake value should be small, and therefore large bearing capacity is identified. On the contrary, if the N-value increases linearly, the bearing capacity is small because of large toe quake value. Furthermore, the stiffness of hammer cushion and pile cushion, which is difficult to find correct values, is recommended lower than 500 kN/mm. This study demonstrates that the results of WEAP may be similar to those of CAPWAP and the WEAP can be used to estimate the bearing capacity of embedded piles.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.161-168
• /
• 2006

An experimental investigation was conducted to examine the hysteretic behaviors of ultra-high strength concrete tied columns. The purpose of this study is to investigate the safety of ultra-high strength concrete columns with 100 MPa compressive strength for the requirement of ACI provisions. Eight 1/3 scaled columns were fabricated to simulate an 1/2 story of actual structural members with the cross section $300{\times}300mm$ and the aspect ratio 4. The main variables are axial load ratio, configurations and volumetric ratios of transverse reinforcement. The results show that the deformability of columns are affected by the configurations and volumetric ratios of transverse reinforcement. Especially, it has been found that the behavior of columns are affected by axial load ratio rather than the amounts and the configurations of transverse reinforcement. Consequently, to secure the ductile behavior of 100 MPa ultra-high strength concrete columns, ACI provisions for the requirement of transverse steel may considered axial load level and the details of transverse reinforcement.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.4
• /
• pp.49-57
• /
• 2010

Selecting an appropriate formwork to fit the construction of a high-rise building is an important factor that can influence the success or failure of a construction. Currently, however, the reality is that in domestic high-rise building construction, the selection of an appropriate formwork with consideration of the characteristics of the formwork has not been done in a reasonable manner. To select formwork in a systematic and reasonable fashion, comprehensive consideration is required that must not only include the aspect of construction costs, but also air, quality, safety, and environmental issues. Therefore, this study aims to rationalize the selection process of formwork by applying the scientific method of Analytic Hierarchy Process (AHP) to the selection process of formwork, in terms of construction costs, quality and safety. To do this, the researcher investigated the current status of formwork being used in high-rise residential building construction. Then, based on the results of this investigation, the researcher selected an alternative for the formwork, and taking construction experts as the subjects of this study, conducted a survey on the applicability of the formwork as well as the priority of management thereof when selecting formwork. It is judged that the results of this research will contribute a more scientific and reasonable decision-making process than the existing non-scientific method in selecting formwork for high-rise residential building construction.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.309-316
• /
• 2016

In this study, performance of hardening accelerator types which promote setting and hardening of cement has been reviewed in order to develop early age strength of concrete with compressive strength of 21~27 MPa after examination of strength development of the concrete at early age according to curing temperature and unit cement(binder) content. As results, soluble mineral salt showed better hardening acceleration effect than organic salt in the scope of this study. Also, hydration reaction accelerating effect of $C_3S$ by Soluble mineral salt is effective on development of early age compressive strength and it was shown that the Pt's hydration reaction accelerating effect was the best. Construction duration reduction can be expected by securing compressive strength for prevention of early aged freezing damage in 25hour-curing time under curing temperature at $15^{\circ}C$. Also, it was shown that compressive strength of specimen cured at $5^{\circ}C$ was similar with plain specimen cured at $10^{\circ}C$. Therefore, it is expected that fuel costs and carbon dioxide can be reduced when the same construction duration is considered.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.1
• /
• pp.60-68
• /
• 2012

In this study, the manufacturing process of micro capsulized PCM (phase changing material) for thermal storage performance of latent heat was investigated to save energy during the use of buildings: i.e. use of melamine-type resin as the micro-capsule material and paraffin wax as the inner material that are together used in concrete walls. For the manufacturing process of the micro-capsulized PCM, the amount of SDS addition as surfactant was the key variable and the resulting thermal storage performance depended on the SDS amount. With increasing amount of SDS, the micro capsulation became much easier while the capsule surface became harder. The micro capsules became uniform at an optimum SDS addition. The addition of SDS also affected the thermal capacity: with increasing SDS amount, the heat storage and release tendency at melting point was more clearly manifested. The current investigation is part of a study under progress to explore the use of PCM in concrete walls to save building maintenance cost and energy.

• Journal of the Korea Concrete Institute
• /
• v.21 no.5
• /
• pp.589-597
• /
• 2009

High Performance Fiber-reinforced Cement Composite (HPFRCC) shows the multiple crack and damage tolerance capacity due to the interfacial bonding of the fibers to the cement matrix. For practical application, it is needed to investigate the fractural behavior of HPFRCC and understand the micro-mechanism of cement matrix with reinforcing fiber. This study is devoted to the investigation of the AE signals in HPFRCC under monotonic and cyclic uniaxial compressive loading, and total four series were tested. The major experimental parameters include the type and volume fraction of fiber (PE, PVA, SC), the hybrid type and loading pattern. The test results showed that the damage progress by compressive behavior of the HPFRCC is a characteristic for the hybrid fiber type and volume fraction. It is found from acoustic emission (AE) parameter value, that the second and third compressive load cycles resulted in successive decrease of the amplitude as compared with the first compressive load cycle. Also, the AE Kaiser effect existed in HPFRCC specimens up to 80% of its ultimate strength. These observations suggested that the AE Kaiser effect has good potential to be used as a new tool to monitor the loading history of HPFRCC.