• Communications for Statistical Applications and Methods
• /
• v.11 no.2
• /
• pp.345-353
• /
• 2004

Graphical methods for the specification of the curvature as a function of two predictors are animated to see the effect of an added variable to the model. Through a 3D animated plot it might be difficult to find a sequence of interpretable plots. But examples demonstrate that useful information can be obtained by using rotation technique in 3D plot. Besides 3D plots, an example of 2D animated plot applied to the case of high correlation between predictors and an added predictor is also given. It implies that speed of the convergence to a certain image in a dynamic plot may be understood as an influence of collinearity.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.67-75
• /
• 1998

This study aimed at he experimental and finite element analytic investigation of the effect of preheating on he residual stress of weldment. In this study, an autogenous arc welding was used on type 304 stainless steel and MARC as F.E.M. common code was utilized in analysis The analyses include transient and moving heat source and thermal properties as function of temperature. During welding, the thermal cycles of four locations in the weldment were recorded to investigate of the behavior of thermal stress and residual stress. The experimental and analytic results had good coincidence and show that there are two factors influencing the formation of welding residual stress in preheat process. One is the elevation of welding equilibrium temperature and the other is the increase of amount of heat input. The former decrease welding residual stress and the latter increase welding residual stress. Therefore, the cumulative effects result in the welding residual stress not being improved significantly with preheating in 304 stainless steel.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.7
• /
• pp.98-105
• /
• 1989

To characterize the biological tissue, the new method to measure the ultrasonic velocity is presented in this paper. The influence of the dispersion effect on the estimation of the ultrasonic velocity is mostly neglected. A more efficient method determining the minimum phase spectrum is developed to characterize the frequency dispersion form the spectral magnitude function. To eliminate the frequency dispersion, the signal-decomposition method is also proposed. Computer simulations are performed to verify the algorithms.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.10
• /
• pp.1335-1343
• /
• 1999

This paper presents concrete pattern recognition method to identify the strength of concrete by evidence accumulation with multiple parameters based on artificial intelligence techniques. At first, zero-crossing(ZCR), mean frequency(MEANF), median frequency(MEDF) and autoregressive model coefficient(ARC) are extracted as feature parameters from ultrasonic signal of concrete. Pattern recognition is carried out through the evidence accumulation procedure using distance measured with reference parameters. A fuzzy mapping function is designed to transform the distances for the application of the evidence accumulation method. Results are presented to support the feasibility of the suggested approach for concrete pattern recognition.

• Journal of applied mathematics & informatics
• /
• v.15 no.1_2
• /
• pp.265-275
• /
• 2004

In this paper, multi-objective models for designing 3D trajectory of horizontal wells are developed in a fuzzy environment. Here, the objectives of minimizing the length of the trajectory and the error of entry target point are fuzzy in nature. Some parameters, such as initial value, end value, lower bound and upper bound of the curvature radius, tool-face angle and the arc length of each curve section, are also assumed to be vague and imprecise. The impreciseness in the above objectives have been expressed by fuzzy linear membership functions and that in the above parameters by triangular fuzzy numbers. Models have been solved by the fuzzy non-linear programming method based on Zimmermann [1] and Lee and Li [2]. Models are applied to practical design of the horizontal wells. Numerical results illustrate the accuracy and efficiency of the fuzzy models.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.145-148
• /
• 2003

Thermal characteristics according to the bearing preload arc studied for the four type spindles with high frequency motor. For the analysis. three dimensional models are built considering heat transfer characteristics such as natural and forced convection coefficients, Bearing and motor are main heat generation, and heat generation by ball bearings as a function of load. viscosity and gyroscopic moment effect are considered. Unsteady-state temperature distributions and thermal displacements according to the bearing preload are analyzed by using the finite clement method.

• Journal of ILASS-Korea
• /
• v.5 no.2
• /
• pp.43-52
• /
• 2000

Numerical simulation of steady, non-evaporating hollow-cone sprays interacting with concentric annular air jets is performed using the discrete stochastic particle method in KIVA. The spray characteristics such as SMD, mean droplet velocity, liquid volume flux, air/liquid mass ratio, and droplet number density arc obtained and compared with the measurements involving different air flow rates in large and small annuli. Overall satisfactory agreement is achieved between calculation and experiment except for the deviation in the downstream SMD arising from uncertainty in the size distribution function at injection, and inaccuracy in the averaged spray parameters due to the small volumes of axisymmetric 2-D sector meshes close to the axis.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.158-163
• /
• 1992

This paper describes the estimation of the solid friction in mechanical systems by using the extended Kalman filtering techniques. We proposed two stochastic model for the estimation. The one is the 'parametric model' which represents the friction characteristics by an exponential function with unknown parameters. The other is the 'blind model' which does not assume an explicit model but regard the effect of the friction as an unknown input to a known dynamic system. For both models, we give estimation algorithms to generate the filtered estimate and the smoothed estimate with a fixed lag. The filtered estimate can be generated on-line for compensating the solid friction in mechanical systems. Although on-line applications are impossible, the smoothed estimate is more accurate and can be used to grasp precise friction characteristics. Simulation and experimental results arc presented to show the effectiveness of the proposed techniques.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.171-173
• /
• 1997

This study proposes a method for evaluating composite power system effective load duration curve(CMELDC) al load points. The concept of ELDC in power system planning is very useful and important in HLI as well as HLII. Effective load duration curve of composite power system can be obtained from convolution integral processing or both probability function of unarrival power and load duration curve at load points. The characteristics and effectiveness of this methodology arc illustrated by case studyings of simple system.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.683-687
• /
• 1997

The purpose of this work is to develop a highly reliable solar cell based on the diamond-like carbon(DLC)/silicon heterojunction. Thin films of DLC have been deposited by employing both filtered cathodic vacuum arc(FCVA) and magnetron plasma-enhanced chemical vapor deposition(m-PECVD) systems. Structural, electrical, and optical properties of DLC films deposited are systematically analyzed as a function of deposition conditions, such as magnetic field, substrate bias voltage, gas pressure, and nitrogen content. The I-V measurement has been used to elucidate the mechanism responsible for the conduction process in the DLC/Si junction. Photoresponse characteristics of the junction are measured and its reliability against temperature and light stresses is also analyzed.