• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.267-272
• /
• 1999

In general, printed antennas have a narrow bandwidth characteristic and many people want to find out the method of bandwidth improvement through complicated procedures. So we want to reform the conventional printed antenna characteristic by using the folded dipole's superiority to unit dipole. But it is hard to feed the printed folded dipole antenna, we use the CPW, which is widely used in microwave IC or MMIC applications and have many advantages to the conventional microstrip line, to feed the printed folded slot antenna. It is confirmed that the improvement in the bandwidth characteristic of CPW fed folded slot antenna, as much as 20%, through the measurement of designed and implemented antenna.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.6
• /
• pp.534-538
• /
• 2016

This paper discusses the characteristics and effects of dielectric inner-supports on discone antenna for broadband RF test chamber, and the verification has been performed by simulation. Several design parameters such as the thickness of the gap support, the position of the side support, and the thickness of the side support has been analyzed. The thickness of the gap support affected the reflection coefficient. An effect of the offset of the side support from the center was slight below 3 GHz and significant above 3 GHz. The thickness of the side support did not affect the reflection coefficient or the gain much. The performance of the fabricated discone antenna was in good agreement with the simulated results. This investigation of a dielectric support effects could be used to design a commercial discone antenna for broadband RF test chamber, focusing on electrical performance and mechanical stability.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2019-2024
• /
• 2014

This paper presents a method to optimize the design of a planar-type antenna and reduce the number of design parameters for rapid computation. The electromagnetic characteristics of the structure are analyzed, and Taguchi method is used to identify critical design parameters. Adaptive particle swarm optimization, which has a faster convergence rate than particle swarm optimization, is used to achieve the design goal effectively. A compact dual-band USB dongle antenna is tested to verify the advantage of the proposed method. In this case, we can use only five selected geometrical parameters instead of eighteen to accelerate the optimization of the antenna design. The 10 dB bandwidth for return loss ranges from 2.3 GHz to 2.7 GHz and from 5.1 GHz to 5.9 GHz, covering all the WiBro, Bluetooth, WiMAX, and 802.11 b/g/n WLAN bands in both simulation and measurement. The optimization process enables the antenna design to achieve the required performance with fewer design parameters.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.731-734
• /
• 2002

This paper presents the assessment of input impedance of a sectoral cylindrical cavity-backed slot antenna excited by a probe. This antenna is proposed to be an element of array that can be assembled to be the antenna for UHF TV broadcasting system. The integral equations are derived based on boundary conditions of the proposed structure and are expressed in terms of dyadic Green's functions and unknown currents. The unknown current densities are solved by the Method of Moments and the input impedance is derived subsequently. Numerical results show the variation of input impedance, for the specified dimensions of the antenna, as a function of frequency. This result is validated by measurement and found that the result is sufficiently accurate. The result from this study is useful for the design of a sectoral cylindrical cavity-backed slot antenna excited by a probe.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.9
• /
• pp.2253-2265
• /
• 2012

A novel folded dipole type microstrip patch antenna designed for ultrahigh frequency (UHF) band radio frequency identification (RFID) tag is presented in this paper, which can be used on the metallic objects. The presented antenna is fabricated on a very thin Rogers 5880 substrate with a thickness of 0.508 mm. The structure consists of two folded dipole and two symmetrical shorting pins placed at both sides of feed point. An adjustable frequency response can be easy obtained via modify the location and radius of the shorting pins. The antenna has been analyzed by full wave simulations soft. The simulated bandwidth is about 67.2 MHz, which covers the Europe and North America UHF RFID frequency range. A manufactured prototype has been fabricated and measured to demonstrate the antenna performances. The simulation results agree with the measurement data well. The measured maximum reading range of the prototype can be reached 4.1 m in free space, and 3.2 m on a metal plate whose size is $150{\times}150{\times}8mm^3$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.194-198
• /
• 2004

This paper presents a broadband compact microstrip antenna design with four U slots on the ground plane by using of genetic algorithm. FDTD method is used as fitness function for antenna analysis, and length of rectangular patch, length of ground plane slot, distance from center point to feed point is used as optimization parameter for maximum bandwidth and minimum size. The measurement result of implemented antenna present 10 dB bandwidth of 15.63 ％ and peak gain of 3.61 dBi in the 2.445 GHz, and antenna has a reduced patch size of 54.8 ％ compare with normal microstrip antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.8
• /
• pp.718-729
• /
• 2015

A S / X dual broad band patch antenna with shared aperture structure is fabricated. A $2{\times}2$ perforated patch is used for S-band operation and a $2{\times}2$ patch antenna array is integrated in the $2{\times}2$ perforation for X-band operation. The measurement results of a S / X dual broad band patch antenna with shared aperture structure show the broad band characteristics larger than 20 % in both bands.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.236-244
• /
• 2011

In this paper, we proposed flexible T-DMB dipole-shaped antenna that has strength of glass antenna and also has portability and ease of production. The input impedance of antenna according to vehicle body-effect was considered in order to install the antenna on the top of the front window. Installation position of on-glass antennas are changeable defends on driver, so we proposed Interdigital capacitor in feeding point to achieve matching characteristic with no position limit. The measurement result showed good return loss characteristic-below -6 dB in the T-DMB frequency band and maintained fixed resonant frequency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.628-631
• /
• 2006

This paper explains about the design, fabrication, and measurement of directional dipole antenna for MMDS. The proposed dipole antenna is an electric wave guide with a director at $\lambda/4$ distance and is also designed to have directivity. The high gain antenna is realized by using a reflector at $45^{\circ}degree$. The fabricated antenna shows the return loss of -35dB at the center frequency 2.06GHz and also has the bandwidth of about 310MHz (>15%) under the condition of VSWR<2. The gain of dipole antennas is 11.5dBi.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.5
• /
• pp.519-526
• /
• 2021

In this paper, an array antenna for LOS datalink for mounting UAV(Unmanned Aerial Vehicle) of low-probability of intercept is presented. For low RCS, radome was designed by conformal form, and other components were inserted into the UAV. The antenna of the transmitter and receiver are each composed of 12×12 array antennas, and include a beam steering function by controlling the phase of the unit element for the Uni-directional pattern and the Bi-directional pattern. As a result of the measurement of the manufactured antenna, it was confirmed that all the required specifications were met, and the installing possibility of the UAV platform on low-probability of intercept in the future was confirmed.