• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.331-335
• /
• 2018

This study investigates the directional recrystallization behavior of Ni based oxide dispersion strengthened (ODS) alloy according to the zone annealing velocity. The zone annealing temperature is set as $1390^{\circ}C$, while the zone velocities are set as 2.5, 4, 6, and 10 cm/h, respectively. The initial microstructure observation of the as-extruded sample shows equiaxed grains of random orientation, with an average grain size of 530 nm. On the other hand, the zone annealed samples show a large deviation in grain size depending on the zone velocities. In particular, grains with a size of several millimeters are observed at 2.5-cm/h zone velocity. It is also found that the preferred orientation varies with the zone annealing velocity. On the basis of these results, this study discusses the role of zone velocities in the directional recrystallization of Ni base ODS alloy.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.279-282
• /
• 2002

The effect of field annealing on the velocity changes of magneto surface acoustic wave (MSAW) devices has been investigated for deposited $(Fe_{1-x}Co_x)_{89}Zr_{11}$ (x = 0~1.0) amorphous films. By means of two step field annealing at $195^{\circ}C$ for 10 minute in the magnetic field of 130 Oe, the MSAW device with x=0.4 film among the devices showed the superior velocity change of 0.1 %. This gigantic value was obtained in the DC bias field of 40 Oe at the exciting frequency of 8.7 MHz. It was confirmed that such behavior was due to the variation of differential permeability caused by an optimal stress within the magnetic film.

• Journal of the Korean Magnetics Society
• /
• v.11 no.2
• /
• pp.78-83
• /
• 2001

The thermal characteristics of TMR devices by using Fast Linear Annealing method has been studied. A computer program that employs the finite differential method has been developed to simulate the temperature distribution of a diameter of 4" silicon wafer, which is subjected to radiation heat from the halogen lamp. We adopted the temperature of 350$\^{C}$, which is the highest temperature usually used in annealing for magnetic thin films. We changed moving velocity of the lamp from 0.05 mm/sec to 1 mm/sec. The moving velocity of halogen lamp has less effect on the local peak temperature of the sample only about 40$\^{C}$. Therefore, we may be able to anneal TMR devices in such short time of 1 minute and 40 seconds per one wafer, using the Fast Linear Annealing method.

• Coupled systems mechanics
• /
• v.11 no.4
• /
• pp.285-295
• /
• 2022

Laminated composite plates are utilized extensively in different fields of construction and industry thanks to their advantages such as high stiffness-to-weight ratio. Additionally, they are characterized by their directional properties that permit the designer to optimize their stiffness for specific applications. This paper presents a numerical analysis and optimization study of plates made of composite subjected to low velocity impact. The main aim is to identify the optimum fiber orientations of the composite plates that resist low velocity impact load. First, a three-dimensional finite element model is built using LS DYNA computer software package to perform the impact analyses. The composite plate has been modeled using solid elements. The failure criteria of Tsai-Wu's criterion have been used to control the strength of the composite material. A good agreement has been found between the predicted numerical results and experimental results in the literature which validate the finite element model. Then, an Adaptive Simulated Annealing (ASA) has been used to optimize the response of impacted composite laminate where its objective is to maximize the safety factor by varying the ply angles. The results show that the ASA is robust in the sense that it is capable of predicting the best optimal designs.

• Journal of Information Display
• /
• v.2 no.2
• /
• pp.7-12
• /
• 2001

A viscous Ni solution was coated over amorphous Si thin film for evenly spread of Ni metal source. The Ni s. prepared by dissolving $NiCl_2$ into IN HCI and mixing with propylene glycol. $NiCl_2$ and Ni were deposited on the amorphous film after oven dry and they enabled to obtain a uniform crystallization. The crystallization using the viscous Ni solution was a Ni-silicide mediated process, the same process used with Ni metal layer. The crystallization temperature was lowered to $480^{\circ}C$ by the synergy effect of silicide-mediated crystallization and microwave-induced crystallization. Lateral crystallization was also enhanced such that the velocity of lateral crystallization by microwave annealing became faster than by furnace annealing.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.92-95
• /
• 2003

Asymmetric rolling of AA1050 Al alloy sheets was performed to obtain the shear textures for improving the deep drawability and the grain refinement. The effect of roll velocity ratio on the texture and the grain refinement of 50％ asymmetrically rolled sheets was studied. The textures of the asymmetrically rolled sheets after annealing at 400$^{\circ}C$ for 1 h was also investigated.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.1
• /
• pp.53-57
• /
• 2008

$Pb(ZrTi)O_3$ thin films were prepared on transparent conducting oxides, through sol-gel processing. The processing variables such as spin velocity, spin time and annealing temperature were investigated using a statistical design of experiments. Dielectric properties were determined through capacitance-voltage measurements and electrical characterizations evaluated using current-voltage characteristics. The leakage currents is determined mainly by annealing. The capacitance and breakdown voltage is found to be independent of the processing variables. The sophisticatedly controlled PZT thin films have been confirmed through microscopic images.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.83-87
• /
• 2005

Hardening Constant Velocity joint increases hardness near the surface and the surface improves fatigue life. Although case depth and chemical composition are same, the prior structure of induction hardened Constant Velocity Joint affects the fatigue strength and life during hardening. Therefore torsional fatigue tests of specimens from vaere conducted on induction hardened automotive Constant Velocity joint with various case depths and lrious prior structures, which are obtained by nomalizing, spheriodized annealing and tempering after quenching, woads applied in order to evaluate the relation between prior structure and fatigue strength.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.112-112
• /
• 2009

In this study, the effect of a long post-deposition thermal annealing(600 and 1000 $^{\circ}C$) on the surface acoustic wave (SAW) properties of polycrystalline (poly) aluminum-nitride (AlN) thin films grown on a 3C-SiC buffer layer was investigates. The poly-AlN thin films with a (0002) preferred orientation were deposited on the substrates by using a pulsed reactive magnetron sputtering system. Experimental results show that the texture degree of AlN thin film was reduced along the increase in annealing temperature, which caused the decrease in the electromechanical coupling coefficient ($k^2$). The SAW velocity also was decreased slightly by the increase in root mean square (RMS) roughness over annealing temperature. However, the residual stress in films almost was not affect by thermal annealing process due to small lattice mismatch different and similar coefficient temperature expansion (CTE) between AlN and 3C-SiC. After the AlN film annealed at 1000 $^{\circ}C$, the insertion loss of an $IDT/AlN/3C-SiC/SiO_2/Si$ structure (-16.44 dB) was reduced by 8.79 dB in comparison with that of the as-deposited film (-25.23 dB). The improvement in the insertion loss of the film was fined according to the decrease in the grain size. The characteristics of AlN thin films were also evaluated using Fourier transform-infrared spectroscopy (FT-IR) spectra and X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) images.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.216-221
• /
• 2001

The equivalent source method(ESM) is used for the calculation of the internal pressure field for an enclosure which can have arbitrary boundary conditions and may include internal objects which scatter the sound field. The advantage of using ESM is that it requires relatively low computing cost and is easy to model the internal diffracting objects. In the ESM modelling, some of the equivalent positions are chosen to be the same as the first order images of the source inside the enclosure, some are positioned on a spherical surface some distance outside the enclosure. The normal velocity on the surfaces of the enclosure walls is evaluated at a larger number of positions than there are equivalent sources. The sum of the squared difference between this velocity and the expected is minimized by adjusting the strength of the equivalent sources. This study is on the optimal equivalent source positions, the far field sources. Typically, the far field sources are evenly distributed on a surface of a virtual sphere which is centered at the enclosure with a sufficiently large radius. In this study, optimal far field source locations are searched using simulated annealing method and simulation results showed that optimally located sources gave better accuracy even with a smaller number of far field sources.