• Journal of Microbiology and Biotechnology
• /
• 제31권7호
• /
• pp.967-977
• /
• 2021

A total of 37 bacterial isolates were obtained from dye-contaminated soil samples at a textile processing factory in Nakhon Ratchasima Province, Thailand, and the potential of the isolates to decolorize and biotransform azo dye Reactive Red 141 (RR141) was investigated. The most potent bacterium was identified as Paenibacillus terrigena KKW2-005, which showed the ability to decolorize 96.45% of RR141 (50 mg/l) within 20 h under static conditions at pH 8.0 and a broad temperature range of 30-40℃. The biotransformation products were analyzed by using UV-Vis spectrophotometry and Fourier-transform infrared spectroscopy. Gas chromatography-mass spectroscopy analysis revealed four metabolites generated from the reductive biodegradation, namely sodium 3-diazenylnaphthalene-1,5-disulfonate (I), sodium naphthalene-2-sufonate (II), 4-chloro-1,3,5-triazin-2-amine (III) and N¹-(1,3,5-triazin-2-yl) benzene-1,4-diamine (IV). Decolorization intermediates reduced phytotoxicity as compared with the untreated dye. However, they had phytotoxicity when compared with control, probably due to naphthalene and triazine derivatives. Moreover, genotoxicity testing by high annealing temperature-random amplified polymorphic DNA technique exhibited different DNA polymorphism bands in seedlings exposed to the metabolites. They compared to the bands found in seedlings subjected to the untreated dye or distilled water. The data from this study provide evidence that the biodegradation of Reactive Red 141 by P. terrigena KKW2-005 was genotoxic to the DNA seedlings.

• 대한금속재료학회지
• /
• 제56권12호
• /
• pp.915-920
• /
• 2018

With the development of modern microelectronics technologies, the power density of electronic devices is rapidly increasing, due to the miniaturization or integration of device elements which operate at high frequency, high power conditions. Resulting thermal problems are known to cause power leakage, device failure and deteriorated performance. To relieve heat accumulation at the interface between chips and heat sinks, thermal interface materials (TIMs) must provide efficient heat transport in the through-plane direction. We report on the enhanced thermal conduction of $Al_2O_3-based$ polymer composites, fabricated by the surface wetting and texturing of thermally conductive hexagonal boron nitride(h-BN) nanoplatelets with large anisotropy in morphology and physical properties. The thermally conductive polymer composites were prepared with hybrid fillers of $Al_2O_3$ macro beads and surface modified h-BN nanoplatelets. Hexagonal boron nitride (h-BN) has high thermal conductivity and is one of the most suitable materials for thermally conductive polymer composites, which protect electronic devices by efficient heat dissipation. In this study, we synthesized hexagonal boron nitride nanoparticles by the pyrolysis of cost effective precursors, boric acid and melamine. Through pyrolysis at $900^{\circ}C$ and subsequent annealing at $1500^{\circ}C$, hexagonal boron nitride nanoparticles with diameters of ca. 50nm were synthesized. We demonstrate that the addition of a small amount of calcium fluoride ($CaF_2$) during the preparation of the melamine borate adduct significantly enhanced the crystallinity of the h-BN and assisted the growth of nanoplatelets up to 100nm in diameters. The addition of a small amount of h-BN enhanced the thermal conductivity of the $Al_2O_3-based$ polymer composites, from 1.45W/mK to 2.33 W/mK.

• 대한금속재료학회지
• /
• 제47권8호
• /
• pp.482-487
• /
• 2009

In order to investigate the effects of intermediate heat treatment between cold rolling passes on the hardness and corrosion properties of a Zr alloy incorporating Nb (Zr-1.49Nb-0.38Sn-0.20Fe-0.11Cr) strip, three different intermediate heat treatment processes ($580^{\circ}C{\times}4hrs$, $600^{\circ}C{\times}2hrs$ and $620^{\circ}{\times}1hrs$) were designed based on a recrystallization map and an accumulated annealing parameter. Test samples from the different processes were investigated by a hardness test, corrosion test, and microstructure analysis and appropriate heat-treatment conditions were thereupon proposed. The sample subjected to an intermediate heat treatment of $580^{\circ}C{\times}4hrs$ was harder than that undergoing $600^{\circ}C{\times}2hrs$ and $620^{\circ}C{\times}1hr$ while the corrosion resistance of the sample that received an intermediate heat treatment of $580^{\circ}C{\times}4hrs$ was superior to that of the other specimens. Considering the trade-off of hardness and corrosion resistance, an intermediate heat treatment process of $600^{\circ}C{\times}2hrs$ is proposed to improve the manufacturing process of the alloy strip.

• 산업경영시스템학회지
• /
• 제44권2호
• /
• pp.58-65
• /
• 2021

Meta-heuristic algorithms have been developed to efficiently solve difficult problems and obtain a global optimal solution. A common feature mimics phenomenon occurring in nature and reliably improves the solution through repetition. And at the same time, the probability is used to deviate from the regional optimal solution and approach the global optimal solution. This study compares the algorithm created based on the above common points with existed SA and HS to show advantages in time and accuracy of results. Existing algorithms have problems of low accuracy, high memory, long runtime, and ignorance. In a two-variable polynomial, the existing algorithms show that the memory increases and the accuracy decrease. In order to improve the accuracy, the new algorithm increases the number of initial inputs and increases the efficiency of the search by introducing a direction using vectors. And, in order to solve the optimization problem, the results of the last experiment were learned to show the learning effect in the next experiment. The new algorithm found a solution in a short time under the experimental conditions of long iteration counts using a two-variable polynomial and showed high accuracy. And, it shows that the learning effect is effective in repeated experiments.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.163-163
• /
• 2000

In this research, we used the ion irradiation technique which has an advantae in improving intentionally the properties of surface and interface in a non-equilibrium, instead of the conventional annealing method which has been known to improve the material properties in the equilibrium stat. Cu/Co multilayered films were prepared on SiN4/SiO2/Si substrates by the electron-beam evaporation for the Co layers and the thermal evaporation for the Cu layers in a high vacuum. The ion irradiation with a 80keV Ar+ was carried out at various ion doses in a high vacuum. Hysteresis loops of the films were investigated by magneto-optical polar Kerr spectroscopy at various experimental conditions. The change of atomic structure of the films before and after the ion irradiation was studied by glancing angle x-ray diffraction, and the intermixing between Co and Cu sublayers was confirmed by Rutherford backscattering spectroscopy. The surface roughness and magneto-resistance were measured by atomic force microscopy and with a four-point probe system, respectively. During the magneto-resistance measurement, we changed temperature and the direction of magnetization. From the results of experiments, we found that the change at the interfaces of the Cu/Co multilayered film induced by ion irradiation cause the change of magnetic properties. According to the change in hysteresis loop, the surface inplane component of magnetic easy axis was isotropic before the ion irradiation, but became anisotropic upon irradiation. It was confirmed that this change influences the axial behavior of magneto-resistance. Especially, the magneto-resistance varied in accordance with an external magnetic field and the direction of current, which means that magneto-resistance also shows the uniaxial behavior.

• 생명과학회지
• /
• 제25권8호
• /
• pp.903-909
• /
• 2015

LAMP (Loop-mediated Isothermal Amplification)법은 PCR를 기반으로 등온에서 autocycling 가닥 변위 DNA 합성에 의존하며, Bst polymerase를 사용하여 진단하는 방법이다. 이것은 대상 DNA의 여섯 개의 배열을 인식하는 4개의 특정 primer의 도움을 받아 단시간 안에 병원체를 식별하는 높은 특이성을 지니고 있다. 본 연구에서는 LAMP로 수생에서 위험한 병원체인 Vibrio alginolyticus의 특별한 LAMP primer를 제작하였으며, 신속한 진단을 위해 MgSO₄, dNTP, Betaine, Bst polymerase의 최적 반응 조건의 특이성 및 기존의 PCR보다 10배 정도의 민감하다는 것을 확인하였다. 또한, 디자인 되어진 LAMP primer가 다른 Vibrio 종들 중 오직 V. alginolyticus에서만 반응한 것을 확인 할 수 있었다. 본 논문에서는 병원체 세균인 V. alginolyticus의 빠르고 민감한 효과적인 진단으로 양식 질병들을 조기에 발견할 수 있도록 개발하였다.

• Korean Chemical Engineering Research
• /
• 제49권5호
• /
• pp.541-547
• /
• 2011

$MnSO_45H_2O$와 $(NH_4)S_2O_8$의 수열반응으로 1차원 나노로드들이 침상으로 클러스터화된 구조의 $MnO_2$를 제조하고 그 모폴로지와 결정성을 분석하였다. 수열반응의 조건에 따라 ${\alpha}$-, ${\beta}$-, ${\gamma}-MnO_2$ 등의 전구체가 제조될 수 있는데, 고농도 반응물 및 높은 수열합성 온도($150^{\circ}C$)에서 전기화학적 활성이 우수한 나노로드 클러스터 ${\beta}-MnO_2$의 생성을 확인하였다. 또한 리튬화제 $LiC_3H_3O_2{\cdot}2H_2O$의 농도와 열처리 온도를 변화시키면서 $MnO_2$를 리튬화하여 스피넬계 $LiMn_2O_4$를 제조하고 리튬이온전지 양전극으로서의 특성을 조사하였다. 결과적으로 나노로드 클러스터형 ${\beta}-MnO_2$로부터 고농도 리튬화제와 $800^{\circ}C$ 열처리를 통해 제조한 $LiMn_2O_4$가 정방형 스피넬에 가장 가까운 구조임을 확인하였으며, 120 mAh/g의 우수한 초기 방전용량을 나타내었다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.235-235
• /
• 2003

The development of a buffer layer is an important issue for the second -generation wire, YBCO coated metal wire. The buffer layer demands not only on the prohibition of the reaction between YBCO and metal substrate, but also the proper lattice match and conductivity for high critical current density (Jc) of YBCO superconductor, In order to satisfy these demands, we suggested CaRuO3 as a useful candidate having that the lattice mismatches with Ni (200) and with YBCO are 8.2% and 8.0%, respectively. The CaRuO3 thin films were deposited on Ni substrates using various methods, such as e-beam evaporation and DC and RF magnetron sputtering. These films were investigated using SEM, XRD, pole-figure and AES. In e-beam evaporation, the deposition temperature of CaRuO3 was the most important since both hi-axial texturing and NiO formation between Ni and CaRuO3 depended on it. Also, the oxygen flow rate had i[n effect on the growth of CaRuO3 on Ni substrates. The optimal conditions of crystal growth and film uniformity were 400$^{\circ}C$, 50 ㎃ and 7 ㎸ when oxygen flow rate was 70∼100sccm In RF magnetron sputtering, CaRuO3 was deposited on Ni substrates with various conditions and annealing temperatures. As a result, the conductivity of CaRuO3 thin films was dependent on CaRuO3 layer thickness and fabrication temperature. We suggested the multi-step deposition, such as two-step deposition with different temperature, to prohibit the NiO formation and to control the hi-axial texture.

• 한국재료학회지
• /
• 제8권10호
• /
• pp.961-968
• /
• 1998

상변화형 광디스크의 보호막으로 사용되는 $ZnS-SiO_2$ 유전체막을 RF magnetron 스퍼트링방법에 의하여 제조하는 경우에 기판 바이어스전압의 영향을 조사하기 위하여, 알곤가스 분위기에서 ZnS(80mol%)-$SiO_2$(20mol%)타겟을 사용하여 Si Wafer와 Corning flass 위에 박막을 증착시켰다. 본 실험에서는 여러 실험 변수를 효과적으로 조절하면서 실험의 양을 줄이고 도시의 산포를 동시에 만족시키는 최적조건으로 타겟 RF 출력 200W, 기판 RF 출력 20W, 아르곤 압력 5mTorr과 증착시간 20분을 얻을 수 있었으며, 신뢰구간 95%에서 확인실험을 수행하였다. 증착된 박막의 열적 저항성을 측정하기 위해 $300^{\circ}C$와 $600^{\circ}C$에서 열처리시험을 수행하였고, Spectroscopic Ellipsometry 측정을 통한 광학적 데이터를 바탕으로 Bruggeman EMA(Effective Medium Approximation)방법을 이용하여 기공(void)분률을 측정하였다. 본 연구결과에 의하면 특성치 굴절률에 대하여 기판 바이어스인자와 증착시간 사이에는 서로 교호작용이 강하게 존재함을 확인할 수 있었다. TEM분석과 XRD 분석 결과에 의하면 기판 바이어스를 가한 최적조건에서 증착된 미세조직은 기존의 바이어스를 가하지 않을 조건에서 증착시킨 박막보다 미세한 구조를 가지며, 또한 과도한 바이어스전압은 결정구조의 조대화를 야기시켰다. 그리고 적절한 바이어스전압은 박막의 밀도를 증가시키며, 기공분률을 약 3.7%정도 감소시킴을 확인할 수 있었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.107-108
• /
• 2008

The spectacular development of AMLCDs, been made possible by a-Si:H technology, still faces two major drawbacks due to the intrinsic structure of a-Si:H, namely a low mobility and most important a shift of the transfer characteristics of the TFTs when submitted to bias stress. This has lead to strong research in the crystallization of a-Si:H films by laser and furnace annealing to produce polycrystalline silicon TFTs. While these devices show improved mobility and stability, they suffer from uniformity over large areas and increased cost. In the last decade we have focused on microcrystalline silicon (${\mu}c$-Si:H) for bottom gate TFTs, which can hopefully meet all the requirements for mass production of large area AMOLED displays [1,2]. In this presentation we will focus on the transfer of a deposition process based on the use of $SiF_4$-Ar-$H_2$ mixtures from a small area research laboratory reactor into an industrial gen 1 AKT reactor. We will first discuss on the optimization of the process conditions leading to fully crystallized films without any amorphous incubation layer, suitable for bottom gate TFTS, as well as on the use of plasma diagnostics to increase the deposition rate up to 0.5 nm/s [3]. The use of silicon nanocrystals appears as an elegant way to circumvent the opposite requirements of a high deposition rate and a fully crystallized interface [4]. The optimized process conditions are transferred to large area substrates in an industrial environment, on which some process adjustment was required to reproduce the material properties achieved in the laboratory scale reactor. For optimized process conditions, the homogeneity of the optical and electronic properties of the ${\mu}c$-Si:H films deposited on $300{\times}400\;mm$ substrates was checked by a set of complementary techniques. Spectroscopic ellipsometry, Raman spectroscopy, dark conductivity, time resolved microwave conductivity and hydrogen evolution measurements allowed demonstrating an excellent homogeneity in the structure and transport properties of the films. On the basis of these results, optimized process conditions were applied to TFTs, for which both bottom gate and top gate structures were studied aiming to achieve characteristics suitable for driving AMOLED displays. Results on the homogeneity of the TFT characteristics over the large area substrates and stability will be presented, as well as their application as a backplane for an AMOLED display.