• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.1
• /
• pp.7-13
• /
• 2010

We have investigated effects of the rapid thermal annealing of GaN epilayers by molecular beam epitaxy in nitrogen atmosphere. The improvement of structural properties of the samples was observed after rapid thermal annealing under optimum conditions. This improvement in crystal quality is due to a reduction of the spread in the lattice parameter in epilayers. The annealing has been performed in a rapid thermal annealing furnace at $950^{\circ}C$. The effect of rapid thermal annealing on the structural properties of GaN was studied by x-ray diffraction. The Bragg peak shifts toward larger angle as the annealing time increases. As the thermal treatment time increases, FWHM(full width at half maximum) of the peak slightly increase with its decreases followed and it increases again. Results demonstrate that rapid thermal annealing did not always promote qualities of GaN epilayers. However, rapid thermal annealing under optimum conditions improve structural properties of the samples, elevating their crystal quality with a reduction of inaccuracy in the lattice parameter of the epilayers.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.704-709
• /
• 2019

In this paper, the electrical characteristics of tunneling field effect transistor(TFET) was studied for different annealing conditions. The TFET samples annealed using hydrogen forming gas(4 %) and Deuterium($D_2$) forming gas(4 %). All the measurements were conducted in noise shielded environment. The results show that subthreshold slope(SS) decreased by 33 mV/dec after annealing process compared to before annealing. Under various temperature range, the noise is improved by average of 31.2 % for 10 atm Deuterium gas at $V_G=3V$ condition. It is also noticed that, post metal annealing with $D_2$ gas reduces the noise by average of 30.7 % at $I_D=100nA$ condition.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1277-1280
• /
• 2007

Isothermal activation annealing was carried out using boron doped SLS poly-using an RTA system. We observed different behavior of reverse annealing depending on the implantation conditions.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3B
• /
• pp.333-339
• /
• 1999

$RuO_2$ thin films were prepared with various deposition conditions by rf magnetron sputtering. The films were annealed in vacuum, air, and air-vacuum, after that, the structural and electrical properties of the films were investigated. As the substrate temperature increases, the preferred orientation of the films changes from (101) to (200), and the grain size increases; especially, at $500^{\circ}C$, the size considerably increases. The preferred orientation of the films changes from (200) to (101) and the roughness of surface increase with the increase in oxygen partial pressure. The lowest value of resistivity of $RuO_2$ we prepared is $1.5\times 10^{-5}\Omega\codt\textrm{cm}$ at the conditions of $400^{\circ}C$ and 10% of oxygen partial pressure. After the processes of annealing, the films deposited at $400^{\circ}C$ and a oxygen partial pressure of 10% were relatively stable. The films deposited at $500^{\circ}C$ have denser structure and smoother surface when the films are annealed in vacuum after annealing in air.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.168-171
• /
• 2002

We have demonstrated ramp-edge Josephson junctions using high temperature superconductors without depositing artificial barriers. We fabricated a surface barrier formed naturally during an ion beam etching process and the annealing under the oxygen atmosphere. The experimental results imply that the barrier natures such as the resistivity are varied by the annealing conditions and the ion milling conditions including the beam voltages. Thus, the ann eating and etching conditions should be optimized to obtain excellent junction properties. In optimizing the fabricating factors, the interface-controlled junctions showed resistively shunted junctions like current-voltage characteristics and an excellent uniformity. These junctions exhibited a spread ($1\sigma$) of $I_{c}$ is 10% fur chips containing 7 junctions at 50K.K.

• Korean Journal of Materials Research
• /
• v.18 no.9
• /
• pp.486-491
• /
• 2008

The effect of annealing treatment conditions on the interfacial adhesion energy between electrolessplated Ni film and polyimide substrate was evaluated using a $180^{\circ}$ peel test. Measured peel strength values are $26.9{\pm}0.8,\;22.4{\pm}0.8,\;21.9{\pm}1.5,\;23.1{\pm}1.3,\;16.1{\pm}2.0\;and\;14.3{\pm}1.3g/mm$ for annealing treatment times during 0, 1, 3, 5, 10, and 20 hours, respectively, at $200^{\circ}C$ in ambient environment. XPS and AES analysis results on peeled surfaces clearly reveal that the peeling occurs cohesively inside polyimide. This implies a degradation of polyimide structure due to oxygen diffusion through interface between Ni and polyimide, which is also closely related to the decrease in the interfacial adhesion energy due to thermal treatment in ambient conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.30-33
• /
• 2004

Shallow p+-n junctions were formed by low-energy ion implantation and dual-step annealing processes The dopant implantation was performed into the crystalline substrates using $BF_2$ ions. The annealing was performed with a rapid thermal processor and a furnace. FA+RTA annealing sequence exhibited better junction characteristics than RTA+FA thermal cycle from the viewpoint of junction depth. A new simulator is designed to model boron diffusion in silicon, which is especially useful for analyzing the annealing process subsequent to ion implantation. The model which is used in this simulator takes into account nonequilibrium diffusion, reactions of point defects, and defect-dopant pairs considering their charge states, and the dopant inactivation by introducing a boron clustering reaction. Using a resonable parameter values, the simulator covers not only the equilibrium diffusion conditions but also the nonequilibrium post-implantation diffusion. Using initial conditions and boundary conditions, coupled diffusion equation is solved successfully. The simulator reproduced experimental data successfully.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.2
• /
• pp.99-102
• /
• 2015

Thin film transistors (TFTs) with amorphous 2 wt% silicon-doped zinc tin oxide (a-2SZTO) channel layer were fabricated using an RF magnetron sputtering system, and the effect of post-annealing treatment time on the structural and electrical properties of a-2SZTO systems was investigated. It is well known that Si can effectively reduce the generation of oxygen vacancies. However, it is interesting to note that prolonged annealing could have a bad effect on the roughness of a-2SZTO systems, since the roughness of a-2SZTO thin films increases in proportion to the thermal annealing treatment time. Thermal annealing can control the electrical characteristics of amorphous oxide semiconductor (AOS) TFTs. It was observed herein that prolonged annealing treatment can cause bumpy roughness, which led to increase of the contact resistance between the electrode and channel. Thus, it was confirmed that deterioration of the electrical characteristics could occur due to prolonged annealing. The longer annealing time also decreased the field effect mobility. The a-2SZTO TFTs annealed at 500℃ for 2 hours displayed the mobility of 2.17 cm²/Vs. As the electrical characteristics of a-2SZTO annealed at a fixed temperature for long periods were deteriorated, careful optimization of the annealing conditions for a-2SZTO, in terms of time, should be carried out to achieve better performance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.966-972
• /
• 2010

Single-phase $Sr_2FeMoO_6$ thin films were produced by RF magnetron sputtering for use as electrodes in integrated sensors and found to be good conductors at room temperature. The films were deposited from a powder-type sputtering target under various conditions, and were crystallized by annealing. Elimination of $O_2$ gas during deposition, by the use of a solely Ar sputtering gas under a working pressure as low as possible, and vacuum annealing were important to promote the $Sr_2FeMoO_6$ phase. However, oxygen exclusion from sputtering and annealing was not enough to yield single-phase $Sr_2FeMoO_6$: hydrogen annealing was also required. Film production was optimized by varying the deposition parameters and hydrogen annealing conditions. The film had good electrical conduction, with a low resistivity of $1.6{\times}10^{-2}\Omega{\cdot}cm$ at room temperature.

• Industry Promotion Research
• /
• v.1 no.1
• /
• pp.7-11
• /
• 2016

It was the electrical properties of IGZO prepared by the annealing in a vaccum and an atmosphere conditions to research the current-voltage characteristics. The IGZO film annealed in a vaccum became an amorphous structure but films annealed in an atmosphere condition had a crystal structure. Because of the content of oxygen vacancies during the annealing processes was changed, and the annealing in an atmosphere condition increased the oxygen vacancy in IGZO. Oxygen vacancy in IGZO increased the current and then it was observed the Ohmic contact at IGZO annealed in an atmosphere conditions. However, the IGZO prepared in a vaccum showed the Schottky contact.