• 대한기계학회논문집
• /
• 제19권10호
• /
• pp.2678-2689
• /
• 1995

In this study, a new hot-wire anemometer which has greater sensitivity than that of a constant temperature anemometer (CTA) was proposed. In contrast to CTA, the wire working resistance of the new anemometer increases with flow velocity, that is, the operating mode of the wire becomes variable temperature. The variable temperature anemometer(VTA) was made by substituting a voltage controlled variable resistor such as photoconductive cell or transistor for one of the resistors in the bridge. By positively feeding back the bridge top signal to the input side of these electronic components, the wire overheat ratio could be increased with velocity automatically. Static response analyses of the VTA, constant voltage anemometer (CVA) and CTA were made in detail and calibration experiments were performed to validate the proposed operating principle. The wire operating resistance of the CVA decreases with velocity and this leads to lower sensitivity than that of a CTA. But the sensitivity of the newly proposed VTA is superior to that of a CTA, since the wire overheat ratio increases with velocity. Consequently, it is found that the major factor that is responsible for large sensitivity of a VTA is not the working resistance itself but the change of the wire working resistance with velocity.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.171-172
• /
• 2006

The anemometer on the radar mast of the vessel is equipped to measure wind direction and speed. This project was carried out to verify the position of anemometer which makes anemometer measure exact wind direction and speed. FLUENT was used to perform this analysis.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2001년도 춘계종합학술대회
• /
• pp.672-675
• /
• 2001

본 논문에서 Interpolation Methods를 이용하여 보다 정화한 풍속을 계산하는 방법과 보다 정확한 풍향을 계산하기 위하여 Interpolation Polynomial을 찾는 방법을 제안하였고, 이렇게 제안된 방법을 이용하여 3-Cup Anemometer의 성능을 개선하였다. 우리는 풍향, 풍속의 관측을 위해 기구부는 3-cup Type Anemometer로, 전자부는 Photo Sensor를 이용하여 구현하였다. 정확한 풍속과 풍향의 측정을 위해서는 시스템의 메모리 한계 및 성능을 고려한 시스템 설계와 8비트 Gray Code Film으로 256(= 2$^{8}$ )개의 각도 Data로 360$^{\circ}$를 표현하는 방법이다.

• 센서학회지
• /
• 제26권1호
• /
• pp.66-72
• /
• 2017

The three dimensional ultrasonic anemometer was constructed to reduce the disadvantages of the two-dimensional anemometer and to be free from the use environment. Three pairs of transmitting and receiving ultrasonic sensors were designed to face each other at an angle of $45^{\circ}$ to the upper and lower surfaces at intervals of $120^{\circ}$. 200 kHz ultrasonic sensor Oscillation, transmission and reception, level detection, power supply circuit were designed and U, V, W wind speed vector components were obtained by measuring the time of first received ultrasonic pulse by transmitting pulse ultrasound. It is implemented as firmware in ARM Coretex-M3 processor so that horizontal and vertical wind direction and wind speed can be converted into digital signal by vector calculation. In this study, The three-dimensional ultrasonic anemometer can complement the disadvantages of the two-dimensional anemometer (mechanical and ultrasonic), and it is expected to gradually replace the two-dimensional anemometer due to its high utilization rate by collecting additional information such as vertical wind.

• 풍력에너지저널
• /
• 제9권4호
• /
• pp.9-15
• /
• 2018

In a previous study, a technique for measuring wind speed and direction by using a roll-rotating three-axis ultrasonic anemometer was proposed and verified by wind tunnel tests. In the tests, instead of a roll sensor, roll angle was trimmed to make no up flow in the transformed wind speeds. Verification was done in point of the residual error of the rotation effect treatment. In this study, roll angle was measured from the roll motor encoder and the transformed wind speed and direction on the test section axis were compared with the ones provided to the test section. As a result, up to yaw $20^{\circ}$ at a wind speed of 12 m/sec or over, the RMS error of wind speed was within the double of the ultrasonic anemometer error. But at yaw $30^{\circ}$, it was over the double of the ultrasonic anemometer error. Regardless of wind speed, at yaw $20^{\circ}$ and $30^{\circ}$, the direction error was within the double of the ultrasonic anemometer error. But at yaw $10^{\circ}$ or less, it was within the error of the ultrasonic anemometer itself. This is a very favorable characteristic to be used for wind turbine yaw control.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.1109-1110
• /
• 2011

• 한국생산제조학회지
• /
• 제8권6호
• /
• pp.92-97
• /
• 1999

This paper reports by simple method that is quickly corrected the effects of fluid temperature for the hot wire anemometer. We are concerned with a variable output of hot wire anemometer on arbitrary fluid temperature. Hot wire by measuring boundary layer of turbulent flow has been calibrated by arbitrary temperature lower than 10$0^{\circ}C$, and velocity lower than 20m/s. As a result, we could pick up the temperature factor affected by output of hot wire anemometer from related in output of arbitrary temperature to output of room temperature. By using temperature factor on the output of hot wire anemometer, we also obtained that the relationship of velocity was of no effect by temperature of fluids. About results of calibrated hot wire, uncertainly of velocity is 2.15% at room temperature and 3.1% at arbitrary temperature.

• 센서학회지
• /
• 제25권2호
• /
• pp.86-90
• /
• 2016

A 3D ultrasonic anemometer measures the direction and velocity of wind in a 3D space. The 2D ultrasonic anemometers developed by different manufacturers do not differ significantly in terms of their form or structure. The 3D ultrasonic anemometers, on the other hand, have more diverse forms than their 2D counterparts depending on the measurement algorithms and methods. Designing and reviewing the structure at the initial stage and defining its performance objectives are time-consuming processes. The process can be made cost-effective and time-saving if the validity is tested by model design and structural interpretation, and the structure is designed to withstand high wind velocities. This study presents the results of a 3D ultrasonic anemometer on real sample data by using a 3D modeling program, CATIA, for ultrasonic anemometer modeling.

• 신재생에너지
• /
• 제9권1호
• /
• pp.12-16
• /
• 2013

The nacelle anemometer mounted behind the blade roots of a wind turbine measures distorted wind speed comparable with free-stream wind because of the wake effects caused dependent upon the operation of the wind turbine and the rotation of its blades. The field campaign was carried out to measure free-stream wind speed at a height identical to the height of the nacelle anemometer by deploying a ground-based remote-sensing equipment, LIDAR. It is derived that a third-order polynomial equation for correcting wind speed measured by the nacelle anemometer to undistorted free-stream wind speed incident to a wind turbine. It is anticipated that the derived correction equation enables wind speed measured by the nacelle anemometer to be used as a precise input for a wind turbine performance test and for developing an active control logic.

• 대기
• /
• 제31권1호
• /
• pp.101-112
• /
• 2021

The long-term trend of surface wind speed in Korea is examined for 31 KMA weather stations from 1985 to 2019. Most stations, except Daegwallyeong, have several times of anemometer height changes from tens of centimeters to several meters. To minimize such height change effect on long-term wind trend, the present study adjusts anemometer height in each station to the standard height of 10 m using the power-law wind profile. This adjustment results in non-negligible trend change. For instance, the increasing surface wind speed at Suwon station, which has six times of anemometer height changes in a range of 0.8 m to 20 m, is weakened up to 67% and becomes statistically insignificant. Likewise, the decreasing trend at Andong station, with three times of anemometer height changes in a range of 10 m to 15.5 m, is weakened up to 66%. A similar weakening in long-term trend is observed in most stations regardless of positive and negative trends. However, due to the cancellation between weakened negative trends and weakened positive trends, the station-averaged wind speed trend in Korea does not change much. This result suggests that anemometer height adjustment is crucial for evaluating local wind speed trend but its impact on nation-wide wind speed trend is rather minor.