• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.50-56
• /
• 2002

When the plasma panel is used as a display, frequent discharging are made to occur by alternatively charging each side of the panel to a critical voltage, which causes repeated gas discharges to occur. In this paper, an efficient sustain driver is proposed to achieve a faster rise-time in order to be suitable to widely used ADS driving method. The proposed circuit increases an operational margin up to 20 % compared with conventional approaches improving the recovery efficiency regardless of the variation of panel capacitance. Thanks to the increased operational margin, the brightness decrease problem can be solved without a limitation to sustain pulse width. The principle of operation, and features are illustrated, and verified on a 7.5 inch diagonal panel at 200 kHz operating frequency - based on experimental prototype.

• Journal of Power Electronics
• /
• v.5 no.1
• /
• pp.67-75
• /
• 2005

A high efficiency ZVS PWM asymmetrical half bridge converter for a plasma display panel (PDP) sustaining power modules is proposed in this paper. To achieve the ZVS of power switches for the wide load range, a small additional inductor L/sub 1kg/, which also acts as an output filter inductor, is serially inserted into the transformer's primary side. At that point, to solve the problem of ringing in the secondary rectifier caused by L/sub 1kg/, the proposed circuit employs a structure without the output filter inductor, which helps the voltages across rectifier diodes to be clamped at the output voltage. Therefore, no dissipative RC (resistor capacitor) snubber for rectifier diodes is needed and a high efficiency as well as low noise output voltage can be realized. In addition, since it has no large output inductor filter, the asymmetrical half bridge converter features a simpler structure, lower cost, less mass, and lighter weight. In addition, since all energy stored in L/sub 1kg/ is transferred to the output side, the circulating energy problem can be effectively solved. The operational principle, theoretical analysis, and design considerations are presented. To confirm the operation, validity, and features of the proposed circuit, experimental results from a 425W, 385Vdc/170Vdc prototype are presented.

• Journal of Information Display
• /
• v.6 no.1
• /
• pp.22-27
• /
• 2005

Auxiliary address pulse driving scheme is proposed for controlling and improving the color temperature of the 42-inch WVGA ac-plasma display panel (ac-PDP) without sacrificing total luminance. Under a white-background, the color temperature of 42-inch ac-PDP is improved by about 1,700 K, whereas under a black-background, the color temperature of 42-inch ac-PDP is improved by about 3,200 K. In addition, by properly controlling the luminance in the R, G, and B cells, the color temperature of 42-inch ac-PDP can be raised from 5,827K to 10,705K.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1120-1124
• /
• 2004

Recently, Plasma Display Panel(PDP) has been in the spotlight as one of the next generation flat-panel-display device. However, it has several drawbacks like the low contrast ratio and the low luminance. In this study, a new address waveform is suggested to improve the priming effect and contrast ratio at the address period in the Address Display period Separated(ADS) method. We modified waveform, instead of a conventional waveform, to an address period, for operating on the Plasma Display Panels, which used the conventional gas [He-Ne-Xe〕. When the ramp pulse is added to the address period at the sustain electrode, it is improved on the priming effect and contrast ratio.

• Journal of Information Display
• /
• v.3 no.2
• /
• pp.13-18
• /
• 2002

Numerical simulation is one of the most useful tools to study gas discharge phenomena that occur in alternating current plasma display panel (AC-PDP) cell. Most PDP cell simulations have been performed for two-dimensional cell, is cross-section along the address electrode. We developed a three-dimensional PDP simulator and applied it to a T-shaped electrode cell in order to show the effects of sustain electrode shape that cannot be included in two-dimensional simulation. The dependence of power consumption on electrode shape and area in the simulation showed the same trend as experiment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.8
• /
• pp.704-710
• /
• 2000

Metal electrode materials for plasma display panel should have low electrical resistivity in order to maintain stable gas discharge and have fast response time. They should also hae good film uniformity adhesion and thermal stability. In this study Cr/Cu/Cr metal electrode structure is formed by DC magnetron sputtering. Cr and Cu films were deposited on ITO coated glasses with various DC power density and main pressures as the major parameters. After metal electrodes were formed a heat treatment was followed at 55$0^{\circ}C$ for 20 min in a vacuum furnace. The intrinsic stress of the sputtered Cr film passed a tensile stress maximum decreased and then became compressive with further increasing DC power density. Also with increasing the main pressure stress turned from compression to tension. After heat the treatment the electrical resistivity of the sputtered Cu film of 2${\mu}{\textrm}{m}$ in thickness prepared at 1 motor with the applied power density of 3.70 W/cm$^2$was 2.68 $\mu$$\Omega$.cm With increasing the main pressure the DC magnetron sputtered Cu film became more open structure. The heat treatment decreased the surface roughness of the sputtered Cr/Cu/Cr metal electrodes.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.2
• /
• pp.121-128
• /
• 2002

A new high-efficient energy-recovery circuit is proposed to drive a plasma display panel (PDP) and compared with the conventional circuit. The proposed circuit uses only two inductors and no auxiliary circuit to recover the energy stored in the equivalent intrinsic capacitance of PDP. Therefore it features a simpler structure, less mass, lower cost of production, higher efficiency, and fewer power devices. The very stable and uniform light emitted from PDP proves the high quality of screen. It is suitable for wall-hanging color TVs. The proposed circuit, operating at 200kHz, is verified to be applicable on a 42-inch PDP by experimental results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.2
• /
• pp.45-52
• /
• 2009

This study is related to the realization of high speed address driving method for Full-HD PDP. The new self-priming addressing(SPA) driving scheme was proposed to improve an address discharge time lag, which utilizes the priming effect maintaining the priming discharge during an address period. In this study, the basic characteristics of the priming ramp discharge were investigated and optimize the reset pulse and priming pulse. It is noted that the address discharge time lag is significantly improved from 1.2[${\mu}s$] to 0.8[${\mu}s$] when the slope of the priming ramp pulse is below 0.1[$V/{\mu}s$].

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1089-1092
• /
• 2007

New display technologies including LCD and plasma panels and Digital Light Projection (DLP) systems all offer large screens and impressive picture quality. However, flat-panel displays require a sophisticated picture processing to let these panels perform at their optimum levels. This paper explains why motion compensating techniques combined with frame rate conversion and quasi-impulse driving reduces motion blur and film judder for flat panel displays and presents the IC and its system application using this technique.

• Journal of Information Display
• /
• v.2 no.1
• /
• pp.10-13
• /
• 2001

The addressing time can be reduced by modifying cell structure and/or driving circuits in order to replace the dual scan system by single scan in large ac plasma display panel(PDP). Moreover, the luminance of the PDP can also be increased by decreasing the addressing time. In this paper, various shapes of bus and address electrodes have been investigated with the aim of reducing the addressing time in ADS driving method. The experimental results show that the addressing time can be reduced by more than 30% compared with the conventional type by modifying the electrodes without reducing the luminance of the PDP.