• Progress in Medical Physics
• /
• v.27 no.4
• /
• pp.213-219
• /
• 2016

The position verification of the radiation source utilized in brachytherapy forms a critical factor in determining the therapeutic efficiency. Currently, films are used to verify the source position; however, this method is encumbered by the lengthy time interval required from film scanning to analysis, which makes real-time position verification difficult. In general, the source position accuracy is usually tested in a monthly quality assurance check. In this context, this study investigates the feasibility of the real-time position verification of the radiation source in high dose rate (HDR) brachytherapy with the use of scintillating fibers. To this end, we construct a system consisting of scintillating fibers and a silicon photomultiplier (SiPM), optimize the dosimetric software setup and radiation system characteristics to obtain maximum measurement accuracy, and determine the relative ratio of the measured signals dependent upon the position of the scintillating fiber. According to the dosimetric results based on a treatment plan, in which the dwell time is set at 30 and 60 s at two dwell positions, the number of signals is 31.5 and 83, respectively. In other words, the signal rate roughly doubles in proportion to the dwell time. The source position can also be confirmed at the same time. With further improvements in the spatial resolution and scintillating fiber array, the source position can be verified in real-time in clinical settings with the use of a scintillating fiber-based system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.757-762
• /
• 2010

Owing to the high specific strength and stiffness of composite materials, they are extensively used in mechanical systems and in vehicle industries. However, most mechanical structures experience repeated load and fatigue. Therefore, it is important to perform fatigue analysis of fiber-reinforced composites. The properties of composite laminates vary depending upon the stacking sequence and stacking direction. Fatigue damage of composite laminates occurs according to the following sequence: matrix cracking, delamination, and fiber breakage. In this study, fatigue tests were performed for damage analysis. Fatigue damages, which have to be considered in fatigue analysis, are determined by using the stiffness values calculated from hysteresis loops, and the obtained fatigue damage curve is examined using Mao's equation and Abdelal's equation.

• Composites Research
• /
• v.35 no.2
• /
• pp.53-60
• /
• 2022

This study uses Diglycidyl ether of terephthalylidene-bis-(4-amino-3-methylphenol) (DGETAM), an amine hardener 4,4'-diaminodiphenylethane (DDE) and cationic catalyst N-benzylpyrazinium hexafluoroantimonate (BPH) to make epoxy film. For analysis, ¹H_NMR and FT-IR were used to verify proper synthesis, and the liquid crystallinity of DGETAM was checked using Differntial Scanning Calorimetry and Polarized Optical Microscopy. Thermal conductivity of the sample was measured using Laser Flash Apparatus. Thermal stability as well as thermal conductivity is important when used as a packaging material. Activated energy is the energy needed to generate a response, which can be used to estimate the energy required to maintain physical properties. It was obtained using the Arrhenius equation based on the data measured by isothermal decomposition using Thermogravimetric Analysis. Measurement of the thermal conductivity of epoxy films showed higher thermal conductivity when DDE was used, and it was found that thermal conductivity had an effect on thermal stability, given that it represented an activation energy similar to a film with BPH upon 5% decomposition.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.1899-1909
• /
• 1994

This work presents the experimental and FEM results for the free vibration of cantilevered, symmetrically and antisymmetrically laminated composite rectangular plates. The natural frequencies, mode shapes and contour plots of a number of CFRP, GFRP, DFRP-Aluminum, GFRP-Aluminum and DFRP-GFRP hybrid composite plates are experimentally obtained. Determination of Young's modulus and test procedures are described. The natural frequencies are determined for a wide range of parameters : e.g. , composite material constants, fiber angles and stacking sequences. Natural frequency and nondimensional frequency parameter results are compared with the finite element analysis and existing literatures. Agreement between experimental and calculated frequencies is excellent. The effects of varing the parameters upon the free vibration frequencies and mode shapes are discussed.

• Korean Journal of Rural Living Science
• /
• v.6 no.1
• /
• pp.11-24
• /
• 1995

The new textile materials may be defined as textile materials different from already existing ones in the physical and chemical structure, manufacturing process, or end-use property. The present time what is called the post-industrial society is characterized by rapid change and new technology. Also, textile materials have been changed rapidly and diversely in the post-industrial society than in any other periods. The study aimed to analyze the trend of new tektite materials development in Korea and to forecast the development trend in the future. To investigate the trend of new textile materials, various written materials and informations were collected from the manufacturers, textile related periodicals, and research journals, and they were analyzed. The period of analysis was from January 1992 to May 1995. The results of this research are as followings : (1) Mixed textile materiasl such as bicomponent fiber, blended yam and blended fabric were increased. (2) High technology has an important effect upon new textile material development. (3) functional textile materials were increased (4) The high value-added products were increased. (5) The naturalized textile materials were increased.

• Fashion & Textile Research Journal
• /
• v.19 no.4
• /
• pp.493-503
• /
• 2017

This study investigated water vapor permeability of the 73 breathable fabrics for sports-wear according to the materials, finishing methods and fabric structural parameters. The water vapor permeability by KS K 0594 method of PET breathable fabric was superior than that of nylon one, in addition, water vapor permeability of coated or laminated breathable fabrics were higher than those of hot melt or dot laminated fabrics. The water vapor permeability of breathable fabric was dependent on the thickness, weight and density, which was consistent with measuring method. However, water vapor permeability according to materials and finishing method showed different results according to measuring method. The correlation coefficient of WVP of PET breathable fabrics between ISO and KS K measuring methods was -0.83 and the correlation coefficient of WVP of coated breathable fabrics was -0.72 and -0.71 for KS K and ASTM and -0.72 for KS K and ISO in hot melt laminated breathable fabrics. According to regression analysis, WVP of PET breathable fabric by both KSK and ISO measuring methods was highly dependent upon on the density and weight. In addition, WVP of hot melt laminated breathable fabric was highly dependent upon thickness, weight and density. Therefore, relevant measuring method for WVP of breathable fabrics has to be adopted to measure precise breathability.

• Transactions of Materials Processing
• /
• v.19 no.8
• /
• pp.517-522
• /
• 2010

Selective laser melting (SLM) is emerged as a new manufacturing technique to directly fabricate precise parts using metallic materials. The final characteristics of a component fabricated through the SLM process are strongly dependent upon various parameters such as laser power, scan rate and pulse duration, etc. This paper, therefore, focuses on the dimensional characteristics of melted $20{\mu}m$ Fe-Cr-Ni powder by fiber laser for the selective laser melting process. With energy density decrease, the height and depth were decreased. Although the conditions are of the same energy density, the shape is different by laser power and scan rate. The shapes at various laser parameters were divided into 3 groups based on depth over height. The smooth regular shape is obtained under the conditions of $50{\mu}m$ of powder height and $15-20{\mu}s$ of pulse duration. And the laser power influenced the variation of shape more significantly than the scan rate.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.2
• /
• pp.242-251
• /
• 2010

Experiential marketing focuses on the experience of customers to connect a company and a brand with the lifestyle of customers that influences buying behavior. This study investigates how the persons who experienced brand ambassadors for public relations as experiential marketing recognized brand equity, how personal satisfaction accomplished as a brand ambassador influenced brand equity, and how the effects are different based upon demographic information. The research methodology was a questionnaire distributed to individuals who experienced work as a public relations brand ambassador. A total of 104 returned questionnaires were analyzed by internal validity, t-test, and regression analysis with SPSS 12.0. The results of this study are as follows: Experiential marketing through a public relations brand ambassador positively influenced brand equity. The satisfaction at the company while working as brand ambassador positively influenced brand equity. Experiential marketing influenced more men than women regarding perceived quality and brand loyalty among brand equity. There is no significant differences regarding career (bank or apparel) among brand awareness, brand image, perceived quality, and brand loyalty.

• Nuclear Engineering and Technology
• /
• v.42 no.3
• /
• pp.319-328
• /
• 2010

Bonded tendons have been used in reactor buildings at some operating nuclear power plants in Korea. Assessing prestress force on these bonded tendons has become an important pending problem in efforts to assure continued operation beyond their design life. The System Identification (SI) technique was thus developed to improve upon the existing indirect assessment technique for bonded tendons. As a first step, this study analyzed the sensitivity of the key parameters to prestress force, and then determined the optimal parameters for the SI technique. A total of six scaled post-tensioned concrete beams with bonded tendons were manufactured. In order to investigate the correlation of the natural frequency and the displacement to prestress force, an impact test, a Single Input Multiple Output (SIMO) sine sweep test, and a bending test using an optical fiber sensor and compact displacement transducer were carried out. These tests found that both the natural frequency and the displacement show a good correlation with prestress force and that both parameters are available for the SI technique to predict prestress force. However, displacements by the optical fiber sensor and compact displacement transducer were shown to be more sensitive than the natural frequency to prestress force. Such displacements are more useful than the natural frequency as an input parameter for the SI technique.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.809-819
• /
• 2004

In this paper, in order to exclude the expansion of M/W relay frequency or its new frequency assignment possibly, we analyzed a possibility of substituting M/W system by B-WLL or optical fiber network regarding service quality and economical points. To define the target of service quality, pre-condition and analysis method for the selected media have been derived to compare each other. E1 transmission with BER 10$^{-1}$ was chosen as a reference capacity, and service distance was calculated f3r the selected media as a function of availability. Also from the economical point we considered 3 systems such as optical fiber, M/W, and B-WLL based upon basic system structure, and analyzed them for various line configurations of fiber optic and B-WLL according to service period, system capacity, transmission distance, and data rate. It was confirmed that B-WLL can provide quality of service with 99.999 % availability within 1.6 km cell radius, and for optical fiber substitution, the leased fiber conduit on an electric pole is more economical than M/W system irrespective of service period, but in case of directly digging for underground conduit, it turned out ineffective regardless of cabling duct types.