• 한국생물환경조절학회:학술대회논문집
• /
• 한국생물환경조절학회 2001년도 봄 학술발표논문집
• /
• pp.41-42
• /
• 2001

The objectives of this study were to investigate the effect of the physical properties of wick on the water absorption of substrate. Physical properties of wick in this study were cotton composition, width and length. The water Infiltration rate through the wick was 0.24 ㎝/s at 90 -95% cotton content, which was faster than at 80-85% (0.13 cm/s) and 70-75% (0.08 cm/s). As the cotton content increased, the water absorption of substrate became greater : the amount of absorbed water was about 5-7g higher at 90-95% than at 80-85% and 70-75% at a wick width of 1 ㎝, the velocity of water absorption through the wick was fastest with 0.25 ㎝ㆍs/sup -1/. The amount of absorbed water was higher at 3 ㎝ than at 1 and 2 ㎝. However, the water absorption rate through the cross - sectional area of wick (g H₂O /㎠/hr) was higher at a wick width of 2 ㎝ than at those of 1 and 3 ㎝. The amount of absorbed water in the substrate was higher at 2 : 1 than at 1 : 1 (length in substrate : length out of substrate). Absorbed water amount was larger at 30-40% initial moisture content than any other treatment.

• 생물환경조절학회지
• /
• 제10권2호
• /
• pp.125-131
• /
• 2001

순환식 펄라이트 재배에서 오이의 양액흡수는 일사량 변화와 관계없이 단위일사량당 흡수량이 80~100 mg.MJ$^{-1}$까지 증가 후 일정하게 유지되어 양액흡수 지표는 전체 양액흡수량보다 단위일사량당 양액흡수량이 더 적합하였다. NO￣$_3$-N의 흡수량은 초기에 3 mg.MJ$^{-1}$에서 후기 16 mg.MJ$^{-1}$로 상승하였고 Ca는 초기에 3mg.MJ$^{-1}$에서 후기에 14 mg.MJ$^{-11}$ 로, Mg는 초기에 1 mg.MJ$^{-1}$에서 후기에 5 mg.MJ$^{-1}$로 증가되었으나, 정식 후 62일 이후의 증가세로 둔화되었다. K는 초기에 5.0 mg.MJ$^{-1}$에서 후기 18 mg.MJ$^{-1}$로 증가되었으나 지속적인 증가를 보여주지 못하였는데 이것은 오이의 하엽 제거로 인한 결과로 생각되어진다. 그러나 P는 초기에 0.5 mg.MJ$^{-1}$에서 후기의 3.2mg.MJ$^{-1}$로 지속적으로 증가되었다. S는 초기에 0.5 mg.MJ$^{-1}$에서 증가에 6.5 mg.MJ$^{-1}$까지 증가되다가 후기에 2.7 mg.MJ$^{-1}$로 감소되었다. 오이의 각각의 무기이온 흡수량과 가장 상관이 높았던 요소는 정식일수와 엽면적이었으나 이 두 요소와 단위일사량당 양액흡수량과는 $r^2$=0.92, 0.97로 높은 상관을 보였다. 단위일사량당 양액흡수량을 이용한 각각의 무기이온 흡수량 회귀식은 $r^2$=0.9 이상으로 높은 상관관계를 보여 실용적 이용이 가능할 것으로 보였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권5호
• /
• pp.68-75
• /
• 2021

본 연구에서는 콘크리트의 균열조건에 따른 수분 흡수 현상을 해석적으로 분석하였다. 흡수 시간의 증가에 따라 콘크리트 표면을 통해 흡수되는 수분의 양을 실험적으로 분석한 기존 연구 결과들을 바탕으로 2차원 유한요소해석 모델을 개발하였다. 고려된 균열조건은 균열 폭(0.1 mm, 0.3 mm), 균열 깊이(0 ~ 250 mm), 균열 간격(0 ~ 200 mm)이며 총 30개 모델에 대한 유한요소해석을 수행하였다. 유한요소해석을 수행한 결과, 콘크리트 균열부의 수분 흡수량 증가에 중요한 영향을 미치는 조건은 균열 폭 및 균열 깊이의 변화로 확인되었다. 또한 비균열 조건의 콘크리트에 비해 균열부에서 추가로 흡수되는 물의 양을 정량적으로 분석하기 위하여, 균열부 수분 흡수계수(S_crack) 개념을 도입하고 이를 추정하기 위한 예측 식을 제안하였다. 균열 깊이에 대한 분석 결과, 콘크리트 균열 폭과 관계없이 균열 깊이 150 mm 이하에서는 균열로 인한 수분 흡수가 활발하게 발생할 수 있음을 확인하였다. 따라서 외부에 노출된 철근콘크리트 구조물은 제설제와 같은 수용액 등의 흡수로 인하여 철근 부식이 발생할 수 있음을 고려하면, 실제 시설물의 균열 조건을 파악하기 위해서는 시설물의 점검 및 진단 시에 기존 균열 폭에 대한 조사뿐만 아니라 균열 깊이에 대한 조사도 함께 수행되어야 할 것으로 판단된다.

• 전기화학회지
• /
• 제1권1호
• /
• pp.55-59
• /
• 1998

방식도막의 수명에 가장 큰 영향을 미치는 물의 흡수과정을 quartz crystal microbalance법 및 임피던스 원리를 이용하여 연구하였다. 도막에 있어서 물의 흡수량과 전해질 농도 변화에 따른 도막의 capacitance를 조사하였다 방식도막에 대한 물의 흡수는 삼투압 작용에 의해서 이루어지고, 흡수 초기단계에서는 도막두께가 얇을수록 흡수량이 많은 것을 알 수 있었다 그리고 도막을 구성하고 있는 수지의 종류 및 결합 가교밀도에 따라서 흡수성이 큰 영향을 받는다는 것을 알 수 있었다. 또한 방식도막에 있어서는 접촉하는 전해질 용액의 농도 변화에 따라 흡$\cdot$탈수 현상이 발생하였으며, 같은 종류의 도막이라도 도막두께가 얇을수록 탈수현상에 따른 capacitance의 증가폭이 큰 것으로 나타났다

• Journal of Plant Biology
• /
• 제22권1_2호
• /
• pp.5-14
• /
• 1979

In several leguminous plants such as acasia, arrowroot and bushclover, growth rate and contents of nitrogen, phosphorus and potassium in the tissues and the variation in the culture media were determined. In water cultrue which was free of added nutrients, nitrogen was found to be largely in the form of nitrate(NO3-N). This NO3-N is believed to be the result of nitrification from NH4-N which was apparently released form the plants. From the studies of organ culture with root segments, the amount of nitrogen released and absorbed was found to be proportional to the amount added to the mediuim. Especially, in the N-plot, the amount of nitrogen absorbed by the tissue reached more than 90% of the amount supplied to the medium already in early stage. On the contrary, in the amount free plot, the amount of nitrogen released from the tissue was lower than the minimum level in the N-plot. The amount of total N and P in the cultured tissue was found to be influenced by the amount of nitrogen addedin the medium. However, the amount of K in the tissue was not related to the nitrogen level in the medium, but rather it was influenced by the amount of added potassium. These findings present little difference in the metabolic pattern among the three species plants studied, and suggest that the woody leguminous plants have some common features in tehir metabolic pattern.

• Corrosion Science and Technology
• /
• 제4권1호
• /
• pp.15-18
• /
• 2005

Hydroxyapatite(HAp) was synthesized using the waste sludge from semiconductor process and used as an anticorrosive pigment. The water absorption of coating pigmented with anticorrosive pigment and the corrosion at interface between coating and substrate were monitored using AC impedance techniques. The anticorrosive performance of HAp was compared with those of red lead(RL) and zinc potassium chromate(ZPC), which have been known as representative anticorrosive pigments. The amount of absorbed water in ZPC- and HAp- pigmented coatings was much higher compared to that in RL-pigmented and unpigmented film. However, it seems that the water absorbed into HAp- or ZPC-pigmented film is beneficial to anticorrosive function. The anticorrosive performance of HAp is superior or at least comparable to those of ZPC and RL. The excellent anticorrosive properties of HAp can be explained by its passivating ability, caused by the reaction of the soluble component of HAp with Fe to form iron phosphate in the presence of water.

• 복식
• /
• 제55권5호
• /
• pp.101-107
• /
• 2005

In this article, mordant absorption rate by the Change of temperature and fabric, discharge level by water washing, mordant density and method in mordant dye are going to be handled. Besides, how treatment method will have an effect on absorption rate and color, is also going to be covered. An atom extinction photometer was used to measure the amount of mordant absorbed in fabric at each temperature and mordant type. It turned out that absorption rate differs according to the type of mordant and sample or temperature. Also it turned out that the mordant input amount has little influence on absorption rate, that is to say, if though you use more mordants, just tiny amount of mordant is going to be absorbed in cloth. It is true that the higher temperature goes up, the better mordant absorption gets. It is found that the type of mordant and sample, treatment period affects the discharge rate. Normally $15{\~}98\%$ mordant comes off the fabric by water washing, to be specific, $17{\~}47\%$ Iron by water washing and it has better performance on cotton and nylon than silk, $1\%{\~}52\%$ Aluminum by water washing and better absorption on silk, $36{\~}89\%$ Chrome by water washing and better absorption on silk, $50{\~}89\%$ copper by water washing and better absorption on silk, poor on cotton. The examination of the K/S values and colors between before and after soaping has been conducted under the circumstance that the test fabrics had been treated at $80^{\circ}C$ for 30 minutes with $0.2\%$ soaping solution. In case of pre-mordanted fabrics, the K/S value nosedived after soaping, meanwhile densely mordanted fabric's K/S value soared but after soaping, it dropped sharply. It turned out that soaping treatment deteriorates absorption much more than water washing. It's considered that $0.1 \%$ (W/V) of mordant density is appropriate.

• 한국자원식물학회지
• /
• 제27권6호
• /
• pp.635-641
• /
• 2014

Scutellaria baicalensis $G_{EORGI}$ (Scutellariae Radix) has been used to clear heat and to dry dampness in the stomach or intestines, which manifests as diarrhea or dysenteric disorder. In this study, we investigated the effective preparation of active components in Scutellariae Radix using the methods of solvent extraction and absorption fractionation for the development of new functional food or pharmaceuticals. The marker substances, baicalin, baicalein, wogonoside, and wogonin were directly isolated from the Scutellariae Radix. There chemical structures were elucidated by spectroscopic analysis. The Scutellariae Radix was extracted with hot water. To enhance yield of flavonoids in Scutellariae Radix, the hot water extract was dissolved in ethanol with concentration dependent manner. The precipitates were separated using centrifugal techniques at 10,000 rpm. Supernatant liquid was applied to the HPLC for quantification of major compounds. Separately, the hot water extract was absorbed on Diaion HP-20 resin. And then, the absorbed fraction was eluted with methanol for HPLC. The contents of baicalin, baicalein, wogonoside and wogonin in different treatment methods were analyzed by HPLC. Total amount of four major components were 16.9% in 50% ethanol extract, 21.7% in 70% ethanol extract, 20.5% in 90% ethanol extract, and 39.3% in absorbed fraction of Diaion HP-20 resin. In these results, we found that resin absorption method is suitable for the extraction of enriched flavonoids from Scutellariae Radix.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3215-3224
• /
• 2022

Latest studies found that for 316LN austenitic stainless steel (ASS), its LCF life decreased noticeably in high temperature water containing a great amount of dissolved oxygen (DO) (2 ppm DO), compared with that in the water containing 50 or 100 ppb DO. This finding is different from previous studies about ASSs. This study confirmed that the 316L had similar behavior to 316LN. The LCF life of 316L in water containing 1000 ppb DO water was considerably shorter than that in the water containing 50 ppb DO. Addition of boric acid & lithium hydroxide and pre-soaking did not display noticeable effects on the LCF life of this material in the water with 1000 ppb DO, indicating the discrepancy between the latest studies and previous studies was not caused by the boric acid & lithium hydroxide and pre-soaking. This study also confirmed that similar to 316LN, when a certain amount of DO was added into the water, the amount of hydrogen absorbed into the material decreased significantly compared with that when the DO was less than 5 ppb.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.317-318
• /
• 2023

This study is part of the carbonation degree DB accumulation through quantitative analysis of carbonation depth, Ca(OH)₂ and CO₂ according to the type of finish and years of use of old concrete structures in order to predict the amount of CO₂ that can be absorbed through carbonation of concrete. To this end, the depth of carbonation of the concrete core specimen is measured using an indicator, and the dry amount of water combined with CO₂ in the sample is measured using a differential thermal gravimetric analyzer for samples in the carbonation area and non-carbonated area classified by the indicator, and the absorption compared to the weight of the sample. The amount of absorbed CO₂ was calculated. In addition, the degree of carbonation was calculated through quantitative comparison of Ca(OH)₂ in the carbonation section and non-carbonation section. In the future, we will continue to add the survey and analysis data of dismantled structures and use them as basic data for estimating the amount of carbon dioxide that can be absorbed according to the exposure conditions and years of use by concrete mix.