• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.188.1-188.1
• /
• 2015

For present investigation Fe/MgO/Fe/Co multilayer stack is grown on Si substrate using e-beam evaporation in ultrahigh vacuum. This stack is irradiated perpendicularly by 120 MeV $Ag^{8+}$ at different fluences ranging from $1{\times}10^{11}$ to $1{\times}10^{13}ions/cm^2$ in high vacuum using 15UD Pelletron Accelerator at Inter University Accelerator Centre, New Delhi. Magnetic measurements carried out on pre and post irradiated stacks show significant changes in the shape of perpendicular hysteresis which is relevant with previous observation of re-orientation of magnetic moment along the direction of ion trajectory. However increase in plane squareness may be due to the modification of interface structure of stacks. X-ray reflectivity measurements show onset of interface roughness and interface mixing. X-ray diffraction measurements carried out using synchrotron radiation shows amorphous nature of MgO and Co layer in the stack. Peak corresponding body centered Fe [JCPDS-06-0696] is observed in X-ray diffraction pattern of pre and post irradiated stacks. Peak broadening shows granular nature of Fe layer. Estimated crystallite size is $22{\pm}1nm$ for pre-irradiated stack. Crystallite size first increases with irradiation then decreases. Structural quality of these stacks was further studied using transmission electron microscopic measurements. Thickness from these measurements are 54, 36, 23, 58 and 3 nm respectively for MgO, Fe, MgO, Fe+Co and Au layers in the stack. These measurements envisage poor crystallinity of different layers. Interfaces are not clear which indicate mixing at interface. With increase fluence mixing and diffusion was increased in the stack. X-ray absorption spectroscopic measurements carried out on these stacks show changes of Fe valence state after irradiation along with change of O(2p)-metal (3d) hybridized state. Valence state change predicts oxide formation at interface which causes enhanced in-plane magnetization.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.157-157
• /
• 2015

Recently, the growing interest in organic microelectronic devices including OLEDs has led to an increasing amount of research into their many potential applications in the area of flexible electronic devices based on plastic substrates. However, these organic devices require a gas barrier coating to prevent the permeation of water and oxygen because organic materials are highly susceptible to water and oxygen. In particular, high efficiency OLEDs require an extremely low water vapor transition rate (WVTR) of $1{\times}10^{-6}g/m^2day$. The Key factor in high quality inorganic gas barrier formation for achieving the very low WVTR required ($1{\times}10^{-6}g/m^2day$) is the suppression of defect sites and gas diffusion pathways between grain boundaries. In this study NBAS process was introduced to deposit enhanced film density single gas barrier layer with a low WVTR. Fig. 1. shows a schematic illustration of the NBAS apparatus. The NBAS process was used for the $Al_2O_3$ nano-crystal structure films deposition, as shown in Fig. 1. The NBAS system is based on the conventional RF magnetron sputtering and it has the electron cyclotron resonance (ECR) plasma source and metal reflector. $Ar^+$ ion in the ECR plasma can be accelerated into the plasma sheath between the plasma and metal reflector, which are then neutralized mainly by Auger neutralization. The neutral beam energy is controlled by the metal reflector bias. The controllable neutral beam energy can continuously change crystalline structures from an amorphous phase to nanocrystal phase of various grain sizes. The $Al_2O_3$ films can be high film density by controllable Auger neutral beam energy. we developed $Al_2O_3$ high dense barrier layer using NBAS process. We can verified that NBAS process effect can lead to formation of high density nano-crystal structure barrier layer. As a result, Fig. 2. shows that the NBAS processed $Al_2O_3$ high dense barrier layer shows excellent WVTR property as a under $2{\times}10^{-5}g/m^2day$ in the single barrier layer of 100nm thickness. Therefore, the NBAS processed $Al_2O_3$ high dense barrier layer is very suitable in the high efficiency OLED application.

• Journal of Periodontal and Implant Science
• /
• v.29 no.1
• /
• pp.51-63
• /
• 1999

Exposure of the root surface due to gingival recession after periodontal surgery, elicit pain response when exposed to mechanical, heat, chemical or osmotic irritation. Especially patients treated with periodontal surgery, show high frequency. There have been reports that the 1 out of 7 patients complains of dentinal hypersensitivity. There have been many studies on the clinical effects of various materials on the treatment of dentinal hypersensitivity. The purposes of this study were to evaluate the effect of sodium chloride and potassium oxalate and to observe the relationship between the dentinal hypersensitivity and surface characteristics such as dentinal tubule size and number. This study included 20 teeth which were scheduled for extraction and had no pulpal disease. These teeth were divided into Root planing group, EDTA group, NaCl group and Oxalate group. Dentinal hypersensitivity is measured by tactile, pressured air and cold water using NRS (Numerical Rating Scales). Teeth were extracted under local anesthesia and each specimen was sectioned to a size about 3 X 5 mm and was examined under the scanning electron microscope (X2,000) The results were as follows, 1. The EDTA group exhibited significantly increased dentinal hypersensitivity comparing with the other groups. 2. The NaCl and Oxalate groups showed significantly reduced dentinal hypersensitivity comparing with the EDTA group. 3. As a method for dentinal hypersensitivity measurement, it was presumed thet tactile sensitivity test was not sensitive method but air blast test and cold water test were adequate method. 4. In a SEM study, the root planing group exhibited amorphous smear layer and showed no dentinal tubule orifice, but the EDTA group showed the large number of dentinal tubules. On the other hand, the NaCl and Oxalate groups did not show exposed dentinal tubules. The NaCl group showed more rough root surface than the EDTA group, and the Oxalate group showed many participates to be presumed as calcium oxalate particle. As the results from this study, root planing couldn't expose the dentinal tubule and NaCl and potassium oxalate occluded exposed dentinal tubule effectively. Dentinal hypersensitivity has close relationship with the exposure of dentinal tubules, especially with it's size and number.

• Economic and Environmental Geology
• /
• v.45 no.2
• /
• pp.157-167
• /
• 2012

This study aimed to interpret the provenance and firing temperature of pottery from Chipyeongdong site in Gwangju, Korea though mineralogical and geochemical methods and also investigated the post-depositional alteration of pottery in burial environments. It is also presumed that they were made of soils near the site because they have similar mineralogical composition and same geochemical evolution path. Based on the results of mineralogical analysis, the pottery samples are largely divided into 2 groups; $700^{\circ}C$ to $1,000^{\circ}C$ and 1,000 to $1,100^{\circ}C$. At some pottery fired at over $1,000^{\circ}C$, it is thought that the refinement of raw materials were processed to remove macrocrystalline fragments. However, it was found that phosphate in soil environments formed amorphous aggregates with Al and Fe within the pores and voids on pottery fired at the low temperature. It indicates the contamination of pottery after burial.

• Journal of Pharmaceutical Investigation
• /
• v.32 no.3
• /
• pp.185-190
• /
• 2002

To improve the solubility of poorly water-soluble drug and to develop a sustained release tablets, the need for the technique, the formation of solid dispersion with polymeric materials that can potentially enhance the dissolution rate and extent of drug absorption was considered in this study. The 1:1, 1:4, and 1:5 solid dispersions were prepared by spray drying method using PVP K30, ethanol and methylene chloride. The dissolution test was carried out at in phosphate buffer solution at $37^{\circ}C$ in 100 rpm. Solid dispersed drugs were examined using differential scanning calorimetry and scanning electron microscopy, wherein it was found that felodipine is amorphous in the PVP K30 solid dispersion. Felodifine SR tablets were prepared by direct compressing the powder mixture composed of solid dispersed felodipine, lactose, Eudragit and magnesium stearate using a single punch press. In order to develop a sustained-release preparation containing solid dispersed felodipine, a comparative dissolution study was done using commercially existing product as control. The dissolution rate of intact felodipine, solid dispersed felodipine and its physical mixture, respectively, were compared by the dissolution rates for 30 minutes. The dissolution rates of felodipine for 30 minutes from 1:1, 1:4, 1:5 PVP K30 solid dispersion were 70%, 78% and 90%. However, dissolution rate offelodipine from the physical mixture was 5% of drug for 30 minutes. Our developed product Felodipine SR Tablet showed dissolution of 17%, 50% and 89% for 1, 4, and 7 hours. This designed oral delivery system is easy to manufacture, and drug releases behavior is highly reproducible and offers advantages over the existing commercial product. The dissolution rate of felodipine was significantly enhanced, following the formation of solid dispersion. The solid dispersion technique with water-soluble polymer could be used to develop a solid dispersed felodipine SR tablet.

• The Journal of the Korea Contents Association
• /
• v.10 no.6
• /
• pp.329-335
• /
• 2010

Digital imaging detectors can use a variety of detection materials to convert X-ray radiation either to light or directly to electron charge. Many detectors such as amorphous silicon flat panels, CCDs, and CMOS photodiode arrays incorporate a scintillator screen to convert x-ray to light. The digital radiography systems based on semiconductor detectors, commonly referred to as flat panel detectors, are gaining popularity in the clinical & hospital. The X-ray detectors are described between a-Silicon based indirect type and a-Selenium based direct type. The DRS of detectors is used to convert the x-ray to electron hole pairs. Image processing is described by specific image features: Latitude compression, Contrast enhancement, Edge enhancement, Look up table, Noise suppression. The image features are tuned independently. The final enhancement result is a combination of all image features. The parameters are altered by using specific image features in the different several hospitals. The image in a radiological report consists of two image evaluation processes: Clinical image parameters and MTF is a descriptor of the spatial resolution of a digital imaging system. We used the edge test phantom and exposure procedure described in the IEC 61267 to obtain an edge spread function from which the MTF is calculated. We can compare image in the processing parameters to change between original and processed image data. The angle of the edge with respect to the axes of detector was varied in order to determine the MTF as a function of direction. Each MTF is integrated within the spatial resolution interval of 1.35-11.70 cycles/mm at the 50% MTF point. Each image enhancement parameters consists of edge, frequency, contrast, LUT, noise, sensitometry curve, threshold level, windows. The digital device is also shown to have good uniformity of MTF and image parameters across its modality. The measurements reported here represent a comprehensive evaluation of digital radiography system designed for use in the DRS. The results indicate that the parameter enables very good image quality in the digital radiography. Of course, the quality of image from a parameter is determined by other digital devices in addition to the proper clinical image.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.1
• /
• pp.114-120
• /
• 2020

In this study, we analyzed the structural characteristics of soot, which is one of the anticipated regulatory substances of the IMO, and used a novel classification method to distinguish between exhaust soot and engine soot in marine engines. As an extension of a recent study on exhaust soot recycling, annealing was performed at 2,000 ℃ on engine soot to determine whether it could be recycled. Soot samples before and after annealing were analyzed using HR-TEM and Raman spectroscopy. The HR-TEM results showed that exhaust soot and engine soot had similar nanostructures; the exhaust soot has a spherical primary particle with a chain-like structure, whereas engine soot particles have amorphous structures. The Raman spectroscopy showed a D-peak and a G-peak for both exhaust soot and engine soot. However, the G/D ratio indicated that the value of exhaust soot was relatively higher than that of engine soot, which implies that the exhaust soot has a more graphitized structure. The analysis of annealed engine soot confirmed that graphitization proceeded without any problems, similar to the exhaust soot. This confirmed that both exhaust soot and engine soot generated by marine diesel engines could be recycled as graphite materials.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.3
• /
• pp.181-191
• /
• 2007

The gemological charateristics of Gwangdong tektites and Baikdusan obsidians were investigated, using microscopy, density and refractive index measurements, X-ray fluorescence spectrometry, Inductively Coupled Plasma Mass spectrometry, X-ray powder diffraction, and electron microprobe analysis. The Gwangdong tektites and Baikdusan obsidians are both black in colour and slightly trans-lucent with various shades of brown when cut into a few mm thick. Both the materials yield conchoidal fracture on broken surface. The tektites occur as tear-drop shapes, ranging from 4 to 10 cm long, and in spheres, from 3 to 5 cm in diameter. On the surface numerous shallow pits up to 3 mm in diameter are present. Mohs' hardness and specific gravity are 5 to 5.5 and 2.66, respectively. The tektites are singly refractive, with an refractive index of 1.51. Numerous spherical air bubbles are randomly scattered throughout the tektites, and silica-rich glass inclusions are occasionally seen. X-ray powder diffraction analysis verifies that they are non-crystalline. The Baikdusan obsidians show very similar properties to those of the Gwangdong tektites, especially in hardness, amorphous nature and fracture. Nevertheless, the Baikdusan obsidian can readily be distinguished from the Gwangdong tektites by refractive index ($1.49{\sim}1.50$), specific gravity (2.67 to 2.68), and inclusions (absence of bubbles and presence of sanidine and magnetite crystals).

• Journal of the Korean Magnetics Society
• /
• v.10 no.3
• /
• pp.123-132
• /
• 2000

Cerium substituted YIG thin films were grown by rf magnetron sputter techniques. We investigated the effects of post-deposition heat-treatment as well as various deposition parameters such as substrate materials, substrate temperature. sputter power, and sputter gas types on the crystallinity, chemical composition, microstructure and magnetic characteristics of the films. Post-deposition heat treatment over 750 $\^{C}$ was applied to crystallize as-prepared amorphous films, and a strong tendency of particular crystallographic planes tying parallel to substrate surface was observed for the post-deposition heat-treated films on GGG substrate. The chemical composition of the films exhibited a wide range of chemical stoichiometry depending on the oxygen fraction of sputter gas, and in particular the composition of the film deposited in sputter gas with an oxygen fraction of R = 10% was Ce$\_$0.23/Y$\_$1.30/Fe$\_$3.50/O$\_$12/. With raising the temperature of post-deposition heat-treatment from 900 $\^{C}$ to 1100 $\^{C}$, the surface roughness of the film on GGG substrates increased from about 3 nm to 40 nm, but their coercive force and ferromagnetic resonance line width decreased from 0.477 kA/m to 0.369 kA/m and from 12.5 kA/m to 8.36 kA/m, respectively.

• Journal of Information Display
• /
• v.11 no.1
• /
• pp.8-11
• /
• 2010

In this study, a new thin films passivation technique using Zn with high electronegativity and $MgF_2$, a fluorine material with better optical transmittance than the sealing film materials that have thus far been reported was proposed. Targets with various ratios of $MgF_2$ to Zn (5:5, 4:6 and 3:7) were fabricated to control the amount of Zn in the passivation films. The Mg-Zn-F films were deposited onto the substrates and Zn was located in the gap between the lattices of $MgF_2$ without chemical metathesis in the Mg-Zn-F films. The thickness and optical transmittance of the deposited passivation films were approximately 200 nm and 80%, respectively. It was confirmed via electron dispersive spectroscopy (EDS) analysis that the Zn content of the film that was sputtered using a 4:6 ratio target was 9.84 wt%. The Zn contents of the films made from the 5:5 and 3:7 ratio targets were 2.07 and 5.01 wt%, respectively. The water vapor transmission rate (WVTR) was determined to be $38^{\circ}C$, RH 90-100%. The WVTR of the Mg-Zn-F film that was deposited with a 4:6 ratio target nearly reached the limit of the equipment, $1\times10^{-3}\;gm^2{\cdot}day$. As the Zn portion increased, the packing density also increased, and it was found that the passivation films effectively prevented the permeation by either oxygen or water vapor. To measure the characteristics of gas barrier, the film was applied to the emitting device to evaluate their lifetime. The lifetime of the applied device with passivation was increased to 25 times that of the PLED device, which was non-passivated.