• Journal of Conservation Science
• /
• v.5 no.1 s.5
• /
• pp.94-104
• /
• 1996

This study was carried on paper mulberry bast fibers, which were cut in the length of it's chip by three kinds. And they cooked by sodium hydroxide (NaOH) and ammonium oxalate (AMOX), and pulping process was studied to inquire some properties of hand made papers. The results were as follows. AMOX pulps had $10\~17\%$ higher than NaOH, but amounts of the residual lignin of it's pulps and residual ash were high, and it surely can't be superior. In the freeness of pulps, AMOX pulps were higher than that of NaOH, but they showed tendency to opposite in view of relation of chip's length kinds. For the AMOX pulps, the physical characteristics test results were higher long fiber pulps than short fiber pulps. Specially, in folding endurance long fiber pulps were a very strong. NaOH pulp's physical characteristics test had shown results that were opposite of there of the AMOX pulps, if the length of the fiber is longer, the strengthts generally decreased. To get the optimum fiber's length according to use of paper and pulping method, they must be fractionate chip's length. The long fibers in NaOH pulps affected the paper quality greatly to length of chips.

• Applied Chemistry for Engineering
• /
• v.3 no.2
• /
• pp.288-295
• /
• 1992

The reduction of nitrobenzene by triirondodecacarbonyl over phase transfer catalysts was investigated. The phase transfer catalysts showed a good yield of aniline at room temperature. Benzyltriethylammonium chloride, tricaprylmethyl ammonium chloride, 18-crown-6 and polyethyleneglycol-400 were good phase transfer catalysts in this reaction. The effect of reaction temperature, concentration of sodium hydroxide and organic solvents on the reaction rate and yield of aniline were studied in this work.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.4
• /
• pp.503-510
• /
• 2011

Ammonia in water which is toxic to human, its concentration is regulated below 0.5 mg/L in drinking water. Current study aimed to develop appropriate models for ammonia stripping using hollow fiber membrane contactor. Two different models were developed during the study. Model 1 was assumed only free ammonia ($NH_3$) transfer in stripping process, whereas the Model 2 was assumed with total ammonia ($NH_3+{NH_4}^+$) transfer. Ammonium chloride ($NH_4CI$), sodium hydroxide(NaOH) were used to make ammonia solution, which was concentration of 25 mg as N/L at a pH of 10.5. The experimental conditions were such that, the liquid flow was in tube-side in upward direction and t he gas flow was on shell-side in downward direction a t room temperature. The experimental and modeling results showed that marginal difference were observed at low gas flux. However the difference between the both models and experimental value were increased when the gas flux was increased. The study concludes that the Model 1 with free ammonia is more appropriate when both models were compared and useful in ammonia stripping process at low gas flux.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.584-584
• /
• 2012

결정형 실리콘 태양전지 공정 중 표면 texturing 공정은 표면에 요철을 형성시켜 반사되는 빛 손실을 줄여서, 증가된 빛 흡수 양에 의해 단락전류(Isc)를 증가시키는데 그 목적이 있다. 표면 texturing 공정은 습식 식각과 건식 식각에 의한 방법으로 나눌 수 있다. 습식 식각은 KOH, TMAH, HNA 등의 실리콘 식각 용액을 사용하여 공정상의 위험도가 크고, 사용 후 용액의 폐기물에 의한 환경오염 문제가 있다. 건식 식각은 습식 식각과 달리 폐기물의 처리가 없고 미량의 가스를 이용한다. 그리고 다결정 실리콘 웨이퍼처럼 불규칙적인 결정방향에도 영향을 받지 않는 장점을 가지고 있어서 건식 식각을 이용한 표면 texturing 공정에 관한 많은 연구가 진행되고 있으며, 특히 RIE(reactive ion etching)를 이용한 태양전지 texturing 공정이 가장 주목을 받고 있다. 하지만 기존의 RIE를 이용하여 표면 texturing 공정을 하게 되면 500 nm 이하의 needle-like 구조의 표면이 만들어진다. Needle-like 구조의 표면은 전극을 형성할 때에 접촉 면적이 좁기 때문에 adhesion이 좋지 않은 것과 단파장 대역에서 광 손실이 많다는 단점이 있다. 본 논문에서는 기존의 RIE texturing의 단점을 보완하기 위해 챔버 내부에 metal-mesh를 장착한 후 RIE를 이용하여 $1{\mu}m$의 피라미드 구조를 형성하였고, RIE 공정 시 ion bombardment에 의한 표면 손상을 제거(RIE damage remove etching)하기 위하여 10초간 TMAH(Tetramethyl -ammonium hydroxide, 25 %) 식각 공정을 하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.2
• /
• pp.27-32
• /
• 2020

Robust and hydrophobic tetraethoxysilane (TEOS) based silica aerogel was synthesized by supercritical alcohol drying with surface modification using the phenyl based silica co-precursor (PTMS). The aerogels were synthesized by hydrolysis and polycondensation reaction in which TEOS and PTMS in methanol were reacted together in presence of oxalic acid and ammonium hydroxide as the catalysts. Supercritical alcohol dried PTMS/TEOS composite silica aerogel were examined for the hydrophobicity, chemical interaction, surface morphology, and textural characteristics. The hydrophobic silica-based aerogels were characterized by Fourier transform infrared spectroscopy to investigate the presence of functional groups and chemical bonds. The prepared silica demonstrates hydrophobicity (76°-149°), a high specific surface area (398 ㎡/g to 739 ㎡/g). The present investigation provides a simple approach to synthesize hydrophobic and thermally stable silica aerogels.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.10
• /
• pp.884-889
• /
• 2009

Recently, the control of size, morphology and dimensionality in inorganic materials has been rapidly developed into a promising field in materials chemistry. 3D nanostructured flower-like ZnO architecture with different size and shapes have been simply synthesized by hydrothermal process, using zinc acetate and ammonium hydroxide as reactants. In this study, the ZnO thin-films were deposited by RF magnetron sputtering in other to get high adhesion and uniformity of 3D nanostructured flower-like ZnO architecture on a $SiO_2$ substrate. The XRD patterns identified that the obtained the nanocrystallized ZnO architecture exhibited a wurtzite structure. SEM images illustrated that the flower-like ZnO bundles consisted of flower-like or chestnut bur, which were characterized by polycrystalline and (002) preferential orientation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.317-317
• /
• 2010

This paper reports syntheses of $TiO_2$ nanocubes and theirs application to DSSC. We synthesized $TiO_2$ nanocubes via solvothermal method using titanium isopropoxide (TTIP) and tetramethylammoiumhydroxide (TMAH). By adding longer alkyl chain ammonium hydroxide that slowed down the growth rate of the crystal, $TiO_2$ nanocubes were obtained with average particle size in the range of 40 nm to 70 nm. By TEM investigation, each particle was found to be single crystal of anatase having six-faces of (001) and {100} crystallographic planes truncated by {101} series of planes, which are clearly distinguishable from spherical nanoparticles. Among various application, utilizing nanocubes as photo-electrode in dye-sensitized solar cell, we investigated photo-electron conversion performances in comparison with spherical shaped $TiO_2$ nanoparticles by I-V characteristics and IPCE measurements, etc.. Photocurrent-transient analysis revealed that $TiO_2$ nanocubes have a higher transient electron transfer rate by more than 10 times compared with spherical particles of similar size. Fast electron transport along the cube edges having small curvature was suggested as a plausible origin of high diffusion coefficient of electron in nanocube $TiO_2$.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.1
• /
• pp.61-68
• /
• 2019

Well aligned $SnO_2$-doped ZnO nanorods were prepared by single step or 2-step electrochemical depositions in a mixture solution of zinc nitrate hexahydrate, ammonium hydroxide solution and 0.1 M tin chloride pentahydrate. The morphologies of electrochemically deposited $SnO_2$-doped ZnO were transformed from plain (or network) structures at low reduction potential to needles on hills at high reduction potential. Well aligned ZnO was prepared at intermediate potential ranges. Reduction reagent and a high concentration of Zn precursor were required to fabricate $SnO_2$ doped ZnO nanorods. When compared to results obtained by single step electrochemical deposition, 2-step electrochemical deposition produced a much higher density of nanorods, which was ascribed to less potential being required for nucleation of nanorods by the second-step electrochemical deposition because the surface was activated in the first-step. Mechanisms of $SnO_2$ doped ZnO nanorods prepared at single step or 2-step was described in terms of applied potential ranges and mass-/charge- limited transfer.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.617-622
• /
• 2010

We have studied methods to save Si source during the fabrication process of crystalline Si solar cells. One way is to use a thin silicon wafer substrate. As the thickness of the wafers is reduced, mechanical fractures of the substrate increase with the mechanical handling of the thin wafers. It is expected that the mechanical fractures lead to a dropping of yield in the solar cell process. In this study, the mechanical properties of 220-micrometer-solar grade Cz p-type monocrystalline Si wafers were investigated by varying saw-damage etching conditions in order to improve the flexural strength of ultra-thin monocrystalline Si solar cells. Potassium hydroxide (KOH) solution and tetramethyl ammonium hydroxide (TMAH) solution were used as etching solutions. Etching processes were operated with a varying of the ratio of KOH and TMAH solutions in different temperature conditions. After saw-damage etching, wafers were cleaned with a modified RCA cleaning method for ten minutes. Each sample was divided into 42 pieces using an automatic dicing saw machine. The surface morphologies were investigated by scanning electron microscopy and 3D optical microscopy. The thickness distribution was measured by micrometer. The strength distribution was measured with a 4-point-bending tester. As a result, TMAH solution at $90^{\circ}C$ showed the best performance for flexural strength.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.7 no.1
• /
• pp.1-6
• /
• 1974

Meretrix lusoria is one of the most favorite edible bivalves inhabiting wide inter-tidal flats along the western coast of Korea. Over the period of July to September 1973, some specimens from a tidal flat near AnMyun Island were submerged in sea water with various concentrations of ammo-mum hydroxide added and careful observations were made on their fertilization, early development, and metamorphosis of the larvae. The highest rate of fertilization was demonstrated by individuals treated with 1/1000 normal solution of ammonium hydroxide, and their fertilized eggs followed normal development, i. e., two cell stage in 1.2 hours after fertilization, gastrula stage after 4.7 hours, and trochophore stage after 5.6 hours. Within 24 hours after fertilization M. lusoria larvae have acquired the form of early straight-hinge veliger with the mean prodissoconch I length of $112\mu$. It takes seven days to get the umbo stage with the mean shell length of $172\mu$ and twenty days to get the metamorphosing stage with the mean shell length of $232\mu$. The larvae were cultured to the metamorphosing stage with the shell length of $272\mu$ in the laboratory condition. The relationship between the shell length (L) and the shell height (H) in veliger stage is shown as H=1.02325L-24.46425 with a significant difference.