• 대한예방의학회:학술대회논문집
• /
• 2005.10a
• /
• pp.362-362
• /
• 2005

• Tribology and Lubricants
• /
• v.18 no.6
• /
• pp.377-383
• /
• 2002

The tribological role of mass transfer layer was studied with silver coatings under various ranges of load and sliding speed. Silver coating was performed with a functionally gradient coating method. Tests were per-formed in dry sliding conditions, using a ball-on-disk contact configuration, at the load of 0.0196-17.64 N and the sliding speed of 20-1,000 mm/s in ambient air. Optical microscope and EPMA analyses showed that contact surfaces were covered with the mass transfer layers of agglomerated wear particles depending upon the contact conditions, and they greatly influenced the tribological characteristics of the surfaces. However, the formation of mass transfer layer was suppressed as the sliding speed increased, and above a critical sliding speed, no mass transfer layer was able to form. For building up a general framework of triboiogical behavior of the coated silver films, all test data were summarized on a map whose axes are contact pressure and sliding speed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.2
• /
• pp.288-298
• /
• 1999

In spark ignited engines, the electrical spark not only sets the time for the onset of combustion but also is able to greatly influence the character of the initial flame growth and the subsequent combustion, and thereby can influence engine performance. The relative importance of the ignition energy is particularly high under lean or high residual gas or exhaust gas recirculation (EGR). In this study, a modeling of flame Initiation and its development is proposed. Submodels consist in representing of cylinder pressure and temperature, heat transfer to cylinder wall, and flame kernel heat transfer to ambient air and to spark plug electrodes. The breakdown process and the subsequent electrical power input initially control the kernel growth while intermediate growth is mainly dominated by diffusion or conduction. Then, the flame propagates by the chemical energy, and laminar and turbulent flame velocity.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.2
• /
• pp.206-212
• /
• 2009

The pressurized spray system with nitrogen gas was designed to fabricate the spherical AN(ammonium nitrate) particles. When AN melt was sprayed from a nozzle with equivalent diameter of 0.28mm into an ambient dry air, the ligament breakup mechanism of the molten AN was found to be responsible for the droplet formation(or disintegration) of AN melt. In the experimental range of spray temperature with $170{\sim}200^{\circ}C$ and atomization pressure with $0.1{\sim}0.4MPa$, the spherical AN particles with mean diameter of $130{\sim}250{\mu}m$ were obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.97-100
• /
• 1989

Thermistor is the semiconducting material whose electrical resistance is varied with its self heating. In this paper, the improvement of resistance-temperature characteristics of NTC thermistor devices based on NiO was experimented. The specimens were prepared by mixing NiO and Mn$_2$O$_3$(1:1 mole %) and by addition of CuO(1 wt %, 2 wt %, 4 wt %). The specimens were compacted at the pressure of 1000 kg/$\textrm{cm}^2$ and sintered for 1 hour in air ambient at 120$0^{\circ}C$. Reducing CuO additions not only resistance-temperature characteristics, but also increased room temperature resistance.

• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.181-183
• /
• 2012

Syngas laminar flame speed measurements were carried out at atmospheric pressure and ambient temperature using the Bunsen flame configuration with nozzle burner as a fundamental study on flame stability of syngas. Representative syngas mixture compositions ($H_2:CO$) such as 25:75%, 50:50% and 70:25% and equivalence ratios from 0.5 to 1.4 were investigated. The measured laminar flame speeds were in good agreement with the previous numerical data as well as experimental data available in the literatures over a wide range of equivalence ratio tested. It was reconfirmed that the laminar flame speed gradually increased with the increase in $H_2$ content in a fuel mixture. In particular, the significant increasing rate of flame speed was observed with the increase in equivalence ratio.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.94-100
• /
• 1999

The friction and wear behavior of MoS$_2$Coatings were investigated using a pin and disk type tester. The experiment was conducted using silicon nitride as pin material and MoS$_2$-on-bearing steel as disk material under different operating conditions that include linear sliding speeds in the range of 22~66mm/sec, normal loads varying from 9.8~29.4N, corresponding to maximum contact pressure of 1.78~2.830GPa and atmospheric conditions of high vacuum, medium vacuum, ambient air. The results showed that low friction coefficient of the coating has been identified when running in high vacuum and that friction coefficient and wear volume increased with increasing normal load. Also at high load conditions, the friction coefficient and wear volume increased with increasing sliding velocity.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.710-715
• /
• 1994

The program name TOLAPS is an acronym for Take-Off LAnding Profile Simulation. Some of the interesting features of this program is the ability to detect flight performance effects of airport altitude, ambient temperature, air pressure and wind. TOLAPS can also handle effects of TOW and LW. The program user can also calculate profiles by user difined flaps and thrust settings deviating from recommended standard settings for each aircraft. Wind effects on straight out flying as well as turns can also be demonstrated. Output form TOLAPS are either screen graphics of profiles (altitude, speed or thrust versus flight distance) or flight track. Profiles can also be made in a tabular form, ready for use in most airport noise calculation programs. In this way, TOLAPS is a valuable tool to evaluate effects of noise abatement procedures.

• Journal of the Korean institute of surface engineering
• /
• v.22 no.4
• /
• pp.185-196
• /
• 1989

The surface modification of a mild and stainless steel by alumina sprayed coating were studied. The effects of surface roughness and bond coating layer on the adhesive strengthy and durability of sprayed specimens were also investiated. The adhesive strength of ceramic coating was affected by surface roughness and bond coating layer thinkness. That showed excellent undergrit blast time and bond coating layer; 60 sec and 0.15-0.33mm, respectively. The adhesive strength and densification of sprayed coating with air pressure were superior to those of without and fracture was mainly occured at alumina-bond coating interface. Under ambient atmosphere at $800^{\circ}C$, the oxides existed within bond coating layer promote diffusion of oxygen to lower durability of sprayed specimens. In this case, fracure was occured at sudstrate-bond coating interface.

• KIEAE Journal
• /
• v.16 no.3
• /
• pp.95-101
• /
• 2016

Purpose: Recently, high-rise buildings are popular in korea due to high rate of land usage and cost performance in urban area. However, high-rise building causes several problems such as safety issues, cooling/heating load, stack effect, disaster prevention etc. The stack effect is one of the representative problems. Even though there are many researches on stack effect, there are few studies on design guideline considering local condition. Method: This study focuses on the change of pressure distribution according to the design factors which affects the airflow in high-rise residential buildings by simulation analysis. In this study, city, building floor, stairwell door leakage area, elevator door leakage area and changes of layout were considered ad the design factor. Result: The simulation results indicate that building height and ambient air temperature are significant design factor for stack effect.