• 한국안전학회지
• /
• 제15권4호
• /
• pp.28-34
• /
• 2000

Copper clad aluminum composite materials are being used for economic and structural purposes, The development of an efficient production method of copper clad aluminum composite material rods by extrusion is very important. This paper describes experimental investigations in the direct extrusion of copper clad aluminum rods through conical dies. There are several parameters that have an influence on determining a sound clad extrusion. These variables are extrusion temperature, extrusion ratio, semi-cone angle of die, extrusion force, extrusion velocity, friction of between the container and billet, percentage of copper used and ratio of flow stress of copper to aluminum. In order to investigate the influence of extrusion temperature, extrusion ratio, semi-cone angle of die on the hot direct extrudability of the copper clad aluminum composite material rods, the experimental study have been performed with these variation.

• 전자공학회논문지A
• /
• 제31A권10호
• /
• pp.108-113
• /
• 1994

The characteristics of the oxidation prevention layers for the copper metallization were investigated. The thin films such as Cr, TiN and Al were used as the oxidation prevention layers for copper. Ultra thin aluminum films were found to prevent the oxidation of copper up to the highest oxidation annealing temperature among the barrier layers examined in this study. It was found that oxygen did not diffuse into copper through aluminum films because of the aluminum oxide layer formed on the aluminum surface and the ultra thin aluminum film could be a good oxidation barrier layer for the copper metallization.

• 한국정밀공학회지
• /
• 제21권7호
• /
• pp.179-184
• /
• 2004

In this work, a copper-clad aluminum composite was fabricated using hot hydrostatic extrusion with various extrusion ratios (8.5, 19, 49) and semi-die angles (30, 45, 60 degree) at a temperature of 32$0^{\circ}C$, Material characteristics of copper-clad aluminum composites were determined from compression tests and hardness tests The results showed that for ER of 8.5, the optimum semi-die angle was below or equal to 30 degree and a pressure drop was about 31%. For ER of 19, the optimum semi-die angle was in the range of 40 to 50 degree and a pressure drop was about 38%. In the case of ER=49, the optimum semi-die angle was above or equal to 60 degree and a pressure drop was about 36%. Compressive yield strength was maximum for ER of 8.5 and semi-die angle of 30 degree and the value of maximum was 155 MPa. Uniform hardness distribution was obtained as the extrusion ratio increases and the semi-die angle decreases. In the case of ER=8.5 and semi-die angle of 30 degree, the lowest extrusion pressure and the maximum compressive yield strength was obtained. Therefor, it was concluded that the optimum extrusion condition for fabricated copper-clad aluminum composites under hydrostatic pressure environment was ER of 19 and semi-die angle of 30 degree.

• 대한의생명과학회지
• /
• 제16권4호
• /
• pp.323-330
• /
• 2010

Although copper and zinc are essential metals for human health, excessive level of these metals is toxic. Besides, aluminum is known to induce various adverse health effects including neurological disorders. Therefore, monitoring the human body burden of these metals is important in preventing adverse health effects. In this study, we assessed the exposure to copper, zinc, and aluminum among an adult population residing in Daegu and Kyungbuk areas. Based on data from 171 participants, we found that the geometric mean copper, zinc, and aluminum concentrations in hair were $15.1\;{\mu}g/g$ [95% confidence interval (CI): 13.1~17.5], 76.9 (95% CI: 70.4~84.1), and $1.11\;{\mu}g/g$ (95% CI: 0.81~1.51), respectively. The copper concentrations in hair were significantly related to age, education, and residence area. In addition, zinc concentrations in hair were significantly related to age, whereas higher hair aluminum concentrations were related to alcohol drinking. Correlations between copper and zinc in hair had a significant positive correlation. Our findings suggest that the body burden of copper, zinc, and aluminum varies according to demographic factors, and hair could be used as a valuable biological medium for metal exposure.

• 한국군사과학기술학회지
• /
• 제21권5호
• /
• pp.591-598
• /
• 2018

The reaction characteristics of aluminum-copper(II) oxide composites initiated by the electrostatic discharge were studied as changing the aluminum particle size. Three different sizes of aluminum particles with nano-size copper(II)-oxide particle were used in the study. These composites were manufactured by two methods i.e. a shock-gel method and a self-assembly method. The larger aluminum particle size was, the less sensitive and less violent these composites were based on the electrostatic test. On the analysis of high speed camera about ignition appearances and burning time, the burning speed was faster when aluminum particle size was smaller.

• 한국정밀공학회지
• /
• 제18권6호
• /
• pp.166-173
• /
• 2001

Composite materials consists of two or more different material layers. The usefulness of clad metal rods forms the possibilities of combination of properties of different metals. Copper clad aluminum composite materials are being used for economic and structural purpose. In this study, composite billet consists of commercially pure copper and aluminum(A6061) and experimental conditions consist of the combinations of clad thickness, extrusion ratio, and semi-cone angle of die. In order to investigate the influence of these parameters on the hot direct extrudability of the copper clad aluminum composite material rods, the experimental study have been performed with various extrusion temperatures, extrusion ratios, semi-cone angles of die, and composition rate of Cu:Al.

• 소성∙가공
• /
• 제29권1호
• /
• pp.49-54
• /
• 2020

The influence of electric current on the joining properties of aluminum and copper was investigated. Various pulsed electric current conditions were set to the joining specimens followed by pressure. The shear strength of the joint area between aluminum and copper was measured by the lab shear test. In addition, the microstructures of the joint area were observed through a field emission scanning electron microscope, energy dispersive X-ray, and electron backscatter diffraction. The mechanical properties of each phase in the joint region were measured by nano-indentation. As a result, it was confirmed that electrically assisted solid state joining of copper and aluminum could be applied in various industrial fields.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.759-765
• /
• 2000

A composite material consists of two or more different material layers. Copper clad aluminum composite materials are being used for economic and structural reasons. This study is concerned with experimental investigation in the direct extrusion of copper clad aluminum rods through conical dies. The suggestion are given for the proper extrudability of copper clad aluminum rods via hot direct extrusion. This paper presents the variation of flow state and hardness at a variable of extrusion ratio and semi-angle of die. By measuring after and before extrusion radius ratio of Cu sleeve and Al core, proportional flow state has been considered. And also by measuring hardness, through extrusion way, a variation of hardness has been considered.

• 한국환경보건학회지
• /
• 제3권1호
• /
• pp.13-16
• /
• 1976

Authors investigated the analyse trace elements in vegetables and Ginseng which indicated as follows: 1. Garlic, ginger, and onion has considerably large amounts of magnesium, garlic has in proper sequence as copper, aluminum, magnesium, bromine and mercury. Ginseng has in proper sequence as aluminum, magnesium, copper, bromine and mercury, and onion has in proper sequence as copper, manganese, aluminum, bromine and mercury. 2. Carrot has considerably large amounts of magnesium and has in proper sequence as copper, magnesium, aluminum, bromine and mercury. 3. Ginseng also has large amounts of magnesium and has in proper sequence as magnesium, aluminum, copper, bromine, and mercury.

• 대한기계학회논문집A
• /
• 제25권10호
• /
• pp.1541-1550
• /
• 2001

This paper describes experimental investigations in the direct extrusion of copper clad aluminum rods through conical dies. Composite materials consist of two or more different material layers. Copper clad aluminum composite materials are being used fur economic and structural purposes and the development of an efficient production method of copper clad aluminum composite material rods by extrusion is very important, It is necessary to know the conditions in which successful uniform extrusion ,and sound cladding may be carried out without any defects in the direct extrusion. There are several variables that have an influence on determining a sound clad extrusion. In order to investigate the influence of these parameters on the hot direct extrudability of the copper clad aluminum composite material rods, the experimental study have been performed with various extrusion temperatures, extrusion ratios and semi-cone angles of die. Subsequently, the microscopic inspection of interface bonding is carried out for extruded products. By measuring hardness, along extrusion way of products, a variation of hardness has been discussed. Proportional flow state has been considered by measuring radius ratio of Cu sleeve and Al core before and after extrusion.